ASTM D4115-02(2008)

Standard Performance Specification for Women's and Girls' Knitted and Woven Dress Glove Fabrics

SIGNIFICANCE AND USE
Upon agreement between the purchaser and the supplier, fabrics intended for this end use should meet all of the requirements listed in Table 1 of this performance specification.
It is recognized that for purposes of fashion or aesthetics the ultimate consumer of articles made from these fabrics may find acceptable fabrics that do not conform to all of the requirements in Table 1. Therefore, one or more of the requirements listed in Table 1 may be modified upon agreement between the purchaser and the supplier.
In such cases, any references to the specification shall specify that. “This fabric meets ASTM Specification D 4115 except for the following characteristic(s).”
Where no prepurchase agreement has been reached between the purchaser and the supplier, and in case of controversy, the requirements listed in Table 1 are intended to be used as a guide only. As noted in 5.2, ultimate consumer demands dictate varying performance parameters for any particular style of fabric.
The significance and use of particular properties and methods are discussed in the appropriate sections of the specified methods.
SCOPE
1.1 This performance specification covers woven and knitted fabrics comprised of any textile fiber or mixture of fibers to be used in women's and girls' dress gloves.
1.2 This performance specification is not applicable to fabrics used for interlinings and industrial-protective clothing.
1.3 These requirements apply to the length and width directions for those properties where each fabric direction is pertinent.  
1.4 The following precautinary statement pertains only to the test methods portion, Section 7, of this performance specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

General Information

• Status: Historical
• Publication Date: 31-Jul-2008
• ICS: 61.040 - Headgear. Clothing accessories. Fastening of clothing
• Technical Committee: D13 - Textiles
• Drafting Committee: D13.61 - Apparel

Relations

• Replaces: ASTM D4115-02 - Standard Performance Specification for Women's and Girls' Knitted and Woven Dress Glove Fabrics
• Effective Date: 01-Aug-2008
• Replaced By: ASTM D4115-14 - Standard Performance Specification for Women’s and Girls’ Knitted and Woven Dress Glove Fabrics
• Effective Date: 01-Feb-2014

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:D4115 −02(Reapproved 2008)
Standard Performance Specification for
Women’s and Girls’ Knitted and Woven Dress Glove
1
Fabrics
This standard is issued under the fixed designation D4115; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
3
1. Scope Traverse Tensile Testing Machine) (Withdrawn 1995)
D2724 Test Methods for Bonded, Fused, and Laminated
1.1 This performance specification covers woven and knit-
Apparel Fabrics
ted fabrics comprised of any textile fiber or mixture of fibers to
D3786 Test Method for Bursting Strength of Textile
be used in women’s and girls’ dress gloves.
Fabrics—Diaphragm Bursting Strength Tester Method
1.2 This performance specification is not applicable to
D3787 Test Method for Bursting Strength of Textiles—
fabrics used for interlinings and industrial-protective clothing.
Constant-Rate-of-Traverse (CRT) Ball Burst Test
D5034 TestMethodforBreakingStrengthandElongationof
1.3 These requirements apply to the length and width
directions for those properties where each fabric direction is Textile Fabrics (Grab Test)
4
2.2 AATCC Test Methods:
pertinent.
8 Colorfastness to Crocking: AATCC Crockmeter Method
1.4 The following precautinary statement pertains only to
16 Colorfastness to Light
the test methods portion, Section 7, of this performance
23 Colorfastness to Burnt Gas Fumes
specification. This standard does not purport to address all of
61 Colorfastness to Washing, Domestic, and Laundering,
the safety concerns, if any, associated with its use. It is the
Commercial: Accelerated
responsibility of the user of this standard to establish appro-
116 Colorfastness to Crocking: Rotary Vertical Crockmeter
priate safety and health practices and determine the applica-
Method
bility of regulatory limitations prior to use.
124 Appearance of Durable Press Fabrics After Repeated
Home Launderings
2. Referenced Documents
132 Colorfastness to Drycleaning
2
2.1 ASTM Standards:
135 Dimensional Changes in Automatic Home Laundering
D123 Terminology Relating to Textiles
of Woven or Knit Fabrics
D434 Test Method for Resistance to Slippage of Yarns in
172 Colorfastness to Non-chlorine Bleach in Home Laun-
Woven Fabrics Using a Standard Seam (Withdrawn
dering
3
2003)
188 Colorfastness to Sodium Hypochlorite Bleach in Home
D1424 Test Method for Tearing Strength of Fabrics by
Laundering
Falling-Pendulum (Elmendorf-Type) Apparatus
Evaluation Procedure No. 1 Gray Scale for Color Change
D2261 Test Method for Tearing Strength of Fabrics by the
Evaluation Procedure No. 2 Gray Scale for Staining
Tongue (Single Rip) Procedure (Constant-Rate-of-
Evaluation Procedure No. 3 AATCC Chromatic Transfer-
Extension Tensile Testing Machine)
ence Scale.
D2262 Test Method for Tearing Strength of Woven Fabrics
5
2.3 Federal Standard:
by the Tongue (Single Rip) Method (Constant-Rate-of-
16 CFR, Chapter II—Consumer Product SafetyCommission
Subchapter D—Flammable Fabrics Act Regulations
6
2.4 Military Standard:
1
This performance specification is under the jurisdiction of ASTM Committee
MIL-STD-105D Sampling Procedures and Tables for In-
D13 on Textiles and is the direct responsibility of Subcommittee D13.61 on
Apparel.
spection by Attributes
Current edition approved Aug. 1, 2008. Published October 2008. Originally
approved in 1982. Last previous edition approved in 2002 as D4115 – 02. DOI:
4
10.1520/D4115-02R08. Available from American Association of Textile Chemists and Colorists
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or (AATCC), P.O. Box 12215, Research Triangle Park, NC 27709, http://
contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM www.aatcc.org.
5
Standards volume information, refer to the standard’s Document Summary page on Available from Superintendent of Documents, Government Printing Office,
the ASTM website. Washington, DC 20402.
3
6
The last approved version of this historical standard is referenced on AvailablefromStandardizationDocumentsOrderDesk,Bldg.4SectionD,700
www.astm.org. Robbins Ave., Philadelphia, PA 19111-5094, Attn: NPODS.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
D4115−02 (2008)
NOTE 1—Reference to test methods in this standard give only the
5.2 Itisrecognizedthatforpurposesoffashionoraesthetics
permanent part of the designation of ASTM, AATCC, or other test
the ultimate consumer of articles made from these fabrics may
methods. The currrent edition of each test method cited shall prevail.
find acceptable fabr
...

This document is not anASTM standard and is intended only to provide the user of anASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:D4115–95a Designation: D 4115 – 02 (Reapproved 2008)
Standard Performance Specification for
Women’s and Girls’ Knitted and Woven Dress Glove
1
Fabrics
This standard is issued under the fixed designation D 4115; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This performance specification covers woven and knitted fabrics comprised of any textile fiber or mixture of fibers to be
used in women’s and girls’ dress gloves.
1.2 This performance specification is not applicable to fabrics used for interlinings and industrial-protective clothing.
1.3 These requirements apply to the length and width directions for those properties where each fabric direction is pertinent.
1.4 The following precautinary statement pertains only to the test methods portion, Section 7, of this performance specification.
This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the
user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations
prior to use.
2. Referenced Documents
2
2.1 ASTM Standards:
D 123 Terminology Relating to Textiles
D 434 Test Method for Resistance to Slippage of Yarns in Woven Fabrics Using a Standard Seam
D 1424 Test Method for Tear ResistanceTearing Strength of Woven Fabrics by Falling-Pendulum Type (Elmendorf)Apparatus
D 2261 Test Method for Tearing Strength of Woven Fabrics by the Tongue (Single Rip) MethodProcedure (Constant-Rate-of-
Extension Tensile Testing Machine)
D 2262 Test Method for Tearing Strength of Woven Fabrics by the Tongue (Single Rip) Method (Constant-Rate-of-Traverse
Tensile Testing Machine)
D 2724 Test Methods for Bonded, Fused, and Laminated Apparel Fabrics
D 3786Test Method for Hydraulic Bursting Strength of Knitted Goods and Nonwoven Fabrics—Diaphragm Bursting Strength
Tester Method Test Method for Bursting Strength of Textile FabricsDiaphragm Bursting Strength Tester Method
D 3787 Test Method for Bursting Strength of Knitted Goods—Constant-Rate-of-Traverse TextilesConstant-Rate-of-Traverse
(CRT) Ball Burst Test
D 5034 Test Method for Breaking ForceStrength and Elongation of Textile Fabrics (Grab Test)
3
2.2 AATCC Test Methods:
8 Colorfastness to Crocking: AATCC Crockmeter Method
16 Colorfastness to Light
23 Colorfastness to Burnt Gas Fumes
61 Colorfastness to Washing, Domestic, and Laundering, Commercial: Accelerated
116 Colorfastness to Crocking: Rotary Vertical Crockmeter Method
124 Appearance of Durable Press Fabrics After Repeated Home Launderings
132 Colorfastness to Drycleaning
135 Dimensional Changes in Automatic Home Laundering of Woven or Knit Fabrics
172 Colorfastness to Non-chlorine Bleach in Home Laundering
188 Colorfastness to Sodium Hypochlorite Bleach in Home Laundering
Evaluation Procedure No. 1 Gray Scale for Color Change
1
This specification is under the jurisdiction of ASTM Committee D-13 on Textiles and is the direct responsibility of Subcommittee D13.61 on Apparel.
Current edition approved Dec. 10, 1995. Published May 1996. Originally published as D4115–82. Last previous edition D4115–95.
1
This performance specification is under the jurisdiction of ASTM Committee D13 on Textiles and is the direct responsibility of Subcommittee D13.61 on Apparel.
Current edition approved Aug. 1, 2008. Published October 2008. Originally approved in 1982. Last previous edition approved in 2002 as D 4115 – 02.
2
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at [e-mail]. For Annual Book of ASTM Standards
, Vol 07.01.volume information, refer to the standard’s Document Summary page on the ASTM website.
3
Annual Book of ASTM Standards, Vol 07.02.
3
Available from American Association of Textile Chemists and Colorists (AATCC), P.O. Box 12215, Research Triangle Park, NC 27709, http://www.aatcc.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
D 4115 – 02 (2008)
Evaluation Procedure No. 2 Gray Scale for Staining
Evaluation Procedure No. 3 AATCC Chromatic Transference Scale.
4
2.3 Federal Standard:
16 CFR, Chapter II—Consumer Product Safety Commission Subchapter D—F
...