ASTM D2751-05
(Specification)Standard Specification for Acrylonitrile-Butadiene-Styrene (ABS) Sewer Pipe and Fittings (Withdrawn 2014)
Standard Specification for Acrylonitrile-Butadiene-Styrene (ABS) Sewer Pipe and Fittings (Withdrawn 2014)
ABSTRACT
This specification covers acrylonitrile-butadienestyrene (ABS) sewer pipe, produced by single extrusion or simultaneous multiple coextrusion. This specification also covers fittings. The requirements of this specification are intended to provide pipe and fittings suitable for nonpressure drainage of sewage, surface water, and certain other liquid wastes, in applications outside the building limits. Pipe produced by simultaneous multiple coextrusion shall be classified as “Coex.” Flattening, impact resistance, joint tightness, and pipe stiffness tests shall be performed to conform with specified requirements.
SCOPE
1.1 This specification covers acrylonitrile-butadienestyrene (ABS) sewer pipe, produced by single extrusion or simultaneous multiple coextrusion. This specification also covers fittings. Included are requirements and test methods for materials, dimensions, workmanship, chemical resistance, water resistance, and joint tightness. A form of marking to indicate compliance with this specification is also included.
1.2 The text of this specification references notes, footnotes, and appendixes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification.
The following precautionary caveat pertains only to the test methods portion, Section , of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
WITHDRAWN RATIONALE
This specification covers acrylonitrile-butadienestyrene (ABS) sewer pipe, produced by single extrusion or simultaneous multiple coextrusion. This specification also covers fittings. Included are requirements and test methods for materials, dimensions, workmanship, chemical resistance, water resistance, and joint tightness. A form of marking to indicate compliance with this specification is also included.
Formerly under the jurisdiction of Committee F17 on Plastic Piping Systems, this specification was withdrawn in January 2014 in accordance with section 10.6.3 of the Regulations Governing ASTM Technical Committees, which requires that standards shall be updated by the end of the eighth year since the last approval date.
General Information
Relations
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:D2751 −05 AnAmerican National Standard
Standard Specification for
Acrylonitrile-Butadiene-
1
Styrene(ABS)SewerPipeandFittings
This standard is issued under the fixed designation D2751; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope D2412 Test Method for Determination of External Loading
Characteristics of Plastic Pipe by Parallel-Plate Loading
1.1 This specification covers acrylonitrile-butadienestyrene
D2444 Test Method for Determination of the Impact Resis-
(ABS) sewer pipe, produced by single extrusion or simultane-
tance of Thermoplastic Pipe and Fittings by Means of a
ous multiple coextrusion. This specification also covers fit-
Tup (Falling Weight)
tings.Includedarerequirementsandtestmethodsformaterials,
D3212 Specification for Joints for Drain and Sewer Plastic
dimensions, workmanship, chemical resistance, water
Pipes Using Flexible Elastomeric Seals
resistance, and joint tightness. A form of marking to indicate
D3965 ClassificationSystemandBasisforSpecificationsfor
compliance with this specification is also included.
Rigid Acrylonitrile-Butadiene-Styrene (ABS) Materials
1.2 The text of this specification references notes, footnotes,
for Pipe and Fittings
and appendixes which provide explanatory material. These
F412 Terminology Relating to Plastic Piping Systems
notesandfootnotes(excludingthoseintablesandfigures)shall
F477 Specification for Elastomeric Seals (Gaskets) for Join-
not be considered as requirements of the specification.
ing Plastic Pipe
1.3 The following precautionary caveat pertains only to the
2.2 Federal Standard:
3
test methods portion, Section 8, of this specification: This
Fed. Std. No. 123 Marking for Shipment (Civil Agencies)
standard does not purport to address all of the safety concerns,
2.3 Military Standard:
3
if any, associated with its use. It is the responsibility of the user
MIL-STD-129 Marking for Shipment and Storage
of this standard to establish appropriate safety and health
3. Terminology
practices and determine the applicability of regulatory limita-
tions prior to use.
3.1 Definitions:
3.1.1 Definitions are in accordance with Terminology F412,
2. Referenced Documents
and abbreviations are in accordance with Terminology D1600,
2
2.1 ASTM Standards:
unless otherwise specified. The abbreviation for acrylonitrile-
D618 Practice for Conditioning Plastics for Testing
butadiene-styrene plastic is ABS.
D1600 Terminology forAbbreviatedTerms Relating to Plas-
3.1.2 acrylonitrile-butadiene-styrene (ABS) pipe and fitting
tics
plastics—plastics containing polymers or blends of polymers,
D2122 Test Method for Determining Dimensions of Ther-
or both, in which the minimum butadiene content is 6 %, the
moplastic Pipe and Fittings
minimum acrylonitrile content is 15 %, the minimum styrene
D2235 Specification for Solvent Cement for Acrylonitrile-
or substituted styrene content, or both, is 15 %, and the
Butadiene-Styrene (ABS) Plastic Pipe and Fittings
maximum content of all other monomers is not more than 5 %,
D2321 PracticeforUndergroundInstallationofThermoplas-
plus lubricants, stabilizers, and colorants.
tic Pipe for Sewers and Other Gravity-Flow Applications
4. Significance and Use
1
4.1 The requirements of this specification are intended to
This specification is under the jurisdiction ofASTM Committee F17 on Plastic
Piping Systems and is the direct responsibility of Subcommittee F17.62 on Sewer.
provide pipe and fittings suitable for nonpressure drainage of
Current edition approved May 1, 2005. Published May 2005. Originally
sewage, surface water, and certain other liquid wastes, in
approved in 1968. Last previous edition approved in 1996 as D2751 – 96a. DOI:
applications outside the building limits.
10.1520/D2751-05.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
3
Standards volume information, refer to the standard’s Document Summary page on Available from Standardization Documents Order Desk, Bldg. 4 Section D, 700
the ASTM website. Robbins Ave., Philadelphia, PA 19111-5094, Attn: NPODS.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
D2751−05
NOTE 1—Industrial waste disposal lines should be installed only with
between layers, during testing performed under the require-
the specific approval of the cognizant building code authority, since
ments of this specificat
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.