iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM F969-96

(Practice)

Standard Practice for Construction of Chain-Link Tennis Court Fence

Standard Practice for Construction of Chain-Link Tennis Court Fence

SCOPE
1.1 This practice covers fencing around tennis courts, built from various types of chain-link fabric and framework materials, and installation practices for same.  
1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

General Information

Status
Historical
Publication Date
09-Jan-2001
ICS
97.220.10 - Sports facilities
Technical Committee
F14 - Fences
Drafting Committee
F14.10 - Specific Applications and Other Fence Systems and Components
Current Stage
Ref Project

Relations

Replaced By
ASTM F969-01 - Standard Practice for Construction of Chain-Link Tennis Court Fence
Effective Date
10-Jan-2001
Referred By
ASTM F1553-11(2022) - Standard Guide for Specifying Chain Link Fence
Effective Date
10-Jan-2001

Buy Standard

ASTM F969-96 - Standard Practice for Construction of Chain-Link Tennis Court FenceASTM F969-96 - Standard Practice for Construction of Chain-Link Tennis Court Fence
PreviousNext
Standard
ASTM F969-96 - Standard Practice for Construction of Chain-Link Tennis Court Fence
English language
4 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)


NOTICE: This standard has either been superseded and replaced by a new version or discontinued.
Contact ASTM International (www.astm.org) for the latest information.
Designation: F 969 – 96
AMERICAN SOCIETY FOR TESTING AND MATERIALS
100 Barr Harbor Dr., West Conshohocken, PA 19428
Reprinted from the Annual Book of ASTM Standards. Copyright ASTM
Standard Practice for
Construction of Chain-Link Tennis Court Fence
This standard is issued under the fixed designation F 969; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
1. Scope 4. Summary of Practice
1.1 This practice covers fencing around tennis courts, built 4.1 This practice is intended primarily to guide those
from various types of chain-link fabric and framework mate- responsible for or concerned with the design and installation of
rials, and installation practices for same. chain-link fencing around tennis courts.
1.2 This standard does not purport to address all of the 4.2 This practice does not intend to preclude any practice
safety concerns, if any, associated with its use. It is the that has proven equal to or given better performance under
responsibility of the user of this standard to establish appro- varying conditions such as location, weather, intended use, etc.
priate safety and health practices and determine the applica-
5. Significance and Use
bility of regulatory limitations prior to use.
5.1 The intended use of this practice is for 10- or 12-ft high
2. Referenced Documents
chain-link fencing as complete enclosures around single or
2.1 ASTM Standards: multiple tennis courts, or as backstops at either end of tennis
A 392 Specification for Zinc-Coated Steel Chain-Link courts.
Fence Fabric 5.2 This practice is not intended for applications where
A 491 Specification for Aluminum-Coated Steel Chain- fencing higher than 12 ft is desired for a special application.
Link Fence Fabric 5.3 Caution Regarding Windscreens— If wind screens are
A 824 Specification for Metallic-Coated Steel Marcelled to be installed at the time of fence erection or at a later time, it
Tension Wire for Use with Chain-Link Fence is advisable to use stronger framework and parts and closer
F 552 Definitions of Terms Relating to Chain Link Fencing spacing of posts or back bracing depending upon the type of
F 567 Practice for Installation of Chain-Link Fence screening material to be used, area of fence to be covered, and
F 626 Specification for Fence Fittings local wind conditions.
F 668 Specification for Poly (Vinyl Chloride) (PVC)-
6. Classification
Coated Steel Chain-Link Fence Fabric
6.1 The four types of chain-link fencing described in this
F 900 Specification for Industrial and Commercial Swing
Gates practice are classified as follows:
6.1.1 Type I—Built with aluminum-coated steel chain-link
F 934 Specification for Standard Colors for Polymer-
Coated Chain Link Fence Materials fence fabric as specified in Specification A 491.
F 1043 Specification for Strength and Protective Coatings 6.1.2 Type II—Built with zinc-coated steel chain-link fence
fabric as specified in Specification A 392, Class 1 coating only.
on Metal Industrial Chain Link Framework
F 1083 Specification for Pipe, Steel, Hot-Dipped Zinc 6.1.3 Type III—Built with zinc-5% aluminum-mischmetal
alloy-coated steel chain-link fence fabric as specified in Speci-
Coated (Galvanized) Welded for Fence Structures
F 1345 Specification for Zinc-5% Aluminum-Mischmetal fication F 1345, in a choice of Class 1 or Class 2 coating, as
selected.
Alloy-Coated Steel Chain-Link Fence Fabric
F 1664 Specification for Poly (Vinyl Chloride) (PVC) 6.1.4 Type IV—Built with poly(vinyl chloride) (PVC)-
coated steel chain-link fence fabric as specified in Specification
Coated Steel Tension Wire Used with Chain-Link Fence
F 668, in a choice of Class 1, Class 2a, or Class 2b coating, as
3. Terminology
selected.
3.1 Definitions—See Definitions F 552 for definitions of
7. Ordering Information
terms used in this practice.
7.1 Purchase orders, construction specifications, or detailed
drawings should include the following information:
This practice is under the jurisdiction of ASTM Committee F-14 on Fences and
7.1.1 Quantity or total measurements in lineal feet of fence
is the direct responsibility of Subcommittee F14.10 on Specific Applications.
and gates.
Current edition approved November 10, 1996. Published December 1997.
7.1.2 Type of fence (Type I, II, III or IV) (see 6.1).
Originally published as F 969 – 86. Last previous edition F 969 – 92.
Annual Book of ASTM Standards, Vol 01.06.
F 969
7.1.3 Class of fence if Type III (Class 1 or 2) (see 6.1.3). 8.6.1 All gates shall be fabricated in accordance with
7.1.4 Class of fence if Type IV (Class 1, 2a, or 2b) (see Specification F 900.
6.1.4) and color (see 8.1.2) 8.6.2 Minimum width of gate opening shall be 3 ft.
7.1.5 If framework, fittings and gates are to be color coated, 8.6.3 All single walk gates shall be 7 ft high with a transom
select color from Specification F 934. panel above the gate extending to full height of the fence.
7.1.6 Height of fence (10 or 12 ft). 8.6.4 Gates shall have hinges to provide a full 180° swing
7.1.7 Number of horizontal rails and
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM F3558-24(Guide)
Standard Guide for Chain-Link Pickleball Court Fences

SIGNIFICANCE AND USE
5.1 The Intended Use of This Guide is to identify the specific functions and qualities desired of a pickleball fence and offer recommendations on how to achieve them with a chain link fence for different types of pickleball courts.  
5.2 The Primary Function of a Pickleball Court Fence is to keep pickleball balls in and uninvited traffic out. It also serves as a barrier to prevent players from colliding with fixed objects and spectators. It also prevents players from running onto irregular or slippery surfaces or into dangerous adjacent areas. Fences need to respond to secondary functional requirements, including: spectator viewing, screening the court from wind and visual distractions outside the court, and being as open and welcoming as security conditions permit. In cases where security or dangerous adjacent conditions are an issue, a uniformly high type of enclosure can still be called for, but in most cases, pickleball fences are a variety of heights and may accommodate lights, shade shelters, gates for players and maintenance, and can have completely open (no fence) portions of the perimeter that lead to decks, grandstands, or landscaping
SCOPE
1.1 The purpose of this guide is to inform the builder, designer, facility manager, or owner, or a combination thereof, of a pickleball court or facility about the many details and features of pickleball court fence. It focuses on what to consider when designing a pickleball fence, offers some recommendations, and points the user to where they could find additional useful information regarding the design, construction, and maintenance of pickleball courts.  
1.2 Units—The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    5 pages
    English language
    sale 15% off
  • Guide
    5 pages
    English language
    sale 15% off
ASTM
ASTM F2000-19(Specification)
Standard Safety Performance Specification for Fences for Baseball and Softball Fields

SCOPE
1.1 This specification provides recommended minimum requirements for various types of fences used in softball and baseball ballfields and other sports facilities, and practices for installation.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    6 pages
    English language
    sale 15% off
  • Technical specification
    6 pages
    English language
    sale 15% off
ASTM
ASTM F2699-08(2018)(Guide)
Standard Guide for Fences for Commercial and Public Outdoor Water Spray/Play Areas

SIGNIFICANCE AND USE
5.1 This guide sets forth minimum standard requirements for use in local codes and ordinances relating to commercial and public water spray/play areas.  
5.2 This guide does not have the effect of law, nor is it intended to supersede local codes and ordinances of a more restrictive nature.  
5.3 This guide provides certain recommendations to assist those who intend to provide protection against injuries or fatalities associated with any possible vehicle passage into, or pedestrian passage to or from a water spray/play area environment by children. This would include, but not be limited to, state and local governments, model code organizations, building code groups, and consumers. It is understood that the format will vary depending upon the specific use and local conditions.
SCOPE
1.1 This guide provides the recommended minimum requirements for various types of fences for commercial and public outdoor water spray/play areas.  
1.2 This guide provides for the safety of occupants in water spray/play areas or zones as it pertains to vehicular intrusion as well as other participant intrusion, and for children containment or entry/exit.  
1.3 This guide does not choose the product components for the fence system, the choice of which should be made by the operators of the water spray/play area space and their specification writers or drafters based upon their determination of the merits of the products that could be used.  
1.4 The values stated in inch-pound units are to be regarded as the standard. The SI values stated in parentheses are provided for information purposes only.  
1.5 This guide does not purport to address the aspect of safety within a water spray/play area or zone. It is the responsibility of the user of this guide to establish appropriate safety practices as related to the water spray/play area and determine the applicability of regulatory requirements prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    3 pages
    English language
    sale 15% off
ASTM
ASTM F2698-08(2018)(Guide)
Standard Guide for Fences for Above-Ground and In-ground Skate Park Facilities

SIGNIFICANCE AND USE
5.1 This guide sets forth minimum standard requirements for use in local codes and ordinances relating to fences/barriers separating pedestrian circulation and traffic areas from skate park and related venue enclosures to prevent collision, contain the skateboards and prevent falls into such in-ground venue areas.  
5.2 This guide sets forth minimum standard requirements for use in local codes and ordinances relating to enclosing skate parks and preventing unfamiliar use of the facilities creating falls from hazards.  
5.3 This guide does not have the effect of law, nor is it intended to supersede local codes and ordinances of a more restrictive nature.  
5.4 Studies have been the basis for certain recommendations in this guide and will assist those who intend to provide protection against unfamiliar access by restricting access to children under the age of five years who have no training and others unfamiliar with the equipment and features in skateboards. This would include, but is not limited to, state and local governments, model code organizations, building code groups, and consumers. It is understood that the format will vary depending upon the specific use and local conditions.
SCOPE
1.1 This guide provides recommended minimum requirements for denoting the various types of fences/barriers for skate parks and for inline skating or roller hockey rinks and extreme performance areas.  
1.2 This guide provides the minimum requirements for the protection of the participants from intrusion of other activity users; from unauthorized and unsupervised use by users that could be harmed by unanticipated entry into the area and from falls into in-ground skate park area.  
1.3 This guide provides for the safety of spectators from errant skateboard use.  
1.4 The values stated in inch-pound units are to be regarded as the standard. The SI values in parentheses are provided for information purposes only.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    3 pages
    English language
    sale 15% off
ASTM
ASTM F969-11(2016)(Practice)
Standard Practice for Construction of Chain-Link Tennis Court Fence

SIGNIFICANCE AND USE
5.1 The intended use of this practice is for 10- or 12-ft (3050 or 3660 mm) high chain-link fencing as complete enclosures around single or multiple tennis courts, or as backstops at either end of tennis courts.  
5.2 This practice is not intended for applications where fencing higher than 12 ft (3660 mm) is desired for a special application.  
5.3 Caution Regarding Windscreens—If wind screens are to be installed at the time of fence erection or at a later time, it is advisable to use stronger framework and parts and closer spacing of posts or back bracing depending upon the type of screening material to be used, area of fence to be covered, and local wind conditions. The Chain Link Fence Manufacturers Institute’s (CLFMI), Guide WLG 2445, provides the designer with the process to select the post size and post spacing.
SCOPE
1.1 This practice covers fencing around tennis courts, built from various types of chain-link fabric and framework materials, and installation practices for same.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

  • Standard
    5 pages
    English language
    sale 15% off
ASTM
ASTM F3558-24(Guide)
Standard Guide for Chain-Link Pickleball Court Fences

SIGNIFICANCE AND USE
5.1 The Intended Use of This Guide is to identify the specific functions and qualities desired of a pickleball fence and offer recommendations on how to achieve them with a chain link fence for different types of pickleball courts.  
5.2 The Primary Function of a Pickleball Court Fence is to keep pickleball balls in and uninvited traffic out. It also serves as a barrier to prevent players from colliding with fixed objects and spectators. It also prevents players from running onto irregular or slippery surfaces or into dangerous adjacent areas. Fences need to respond to secondary functional requirements, including: spectator viewing, screening the court from wind and visual distractions outside the court, and being as open and welcoming as security conditions permit. In cases where security or dangerous adjacent conditions are an issue, a uniformly high type of enclosure can still be called for, but in most cases, pickleball fences are a variety of heights and may accommodate lights, shade shelters, gates for players and maintenance, and can have completely open (no fence) portions of the perimeter that lead to decks, grandstands, or landscaping
SCOPE
1.1 The purpose of this guide is to inform the builder, designer, facility manager, or owner, or a combination thereof, of a pickleball court or facility about the many details and features of pickleball court fence. It focuses on what to consider when designing a pickleball fence, offers some recommendations, and points the user to where they could find additional useful information regarding the design, construction, and maintenance of pickleball courts.  
1.2 Units—The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    5 pages
    English language
    sale 15% off
  • Guide
    5 pages
    English language
    sale 15% off
ASTM
ASTM F1551-23(Test Method)
Standard Test Methods for Comprehensive Characterization of Synthetic Turf Playing Surfaces and Materials

SIGNIFICANCE AND USE
5.1 These test methods constitute a standard for obtaining data in research and development, quality control, acceptance and rejection under specifications, and for special purposes.  
5.2 The data obtained from use of these test methods are applicable to the system and its components under conditions of the particular test procedures and are not necessarily the same as the data that might be obtained in other environments or use conditions.  
5.3 The selection of test methods or tests should be limited to those appropriate to the system or material(s) being evaluated.
SCOPE
1.1 These test methods establish a recommended list from which suitable test methods shall be selected for the identification of physical property characteristics and comparison of the performance properties of synthetic turf systems or components for athletic and recreational uses, or both.  
1.2 Some of the test procedures are suitable only for the laboratory characterization of either components or the complete system; others are suitable for tests on installed sports fields; and some tests may be applied in both the laboratory and the field.  
1.3 The test procedures included in these test methods apply as a group to the description of synthetic turf playing surfaces.  
1.4 Test methods outlined herein cover system components as well as fully assembled synthetic turf systems. Most of the methods measure material and performance properties of turf components. Component properties are not intended to represent the performance of a fully assembled turf system. Component results provide data for quality control, specification compliance, and component performance used in product design.  
1.5 Reference to the methods for testing the synthetic turf playing surface and its components contained herein should state specifically the particular test or tests desired and not refer to this list of test methods as a whole.  
1.6 Several new standards have been added since the last revision of this standard. Other standards, for which more appropriate standards exist, have been removed from this standard. A list of the standards that have been removed and their replacements are listed in Table X1.1 in Appendix X1.  
1.7 This is a physical property characterization standard, and it shall not be construed as a safety standard.  
1.8 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.  
1.9 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.10 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    15 pages
    English language
    sale 15% off
  • Standard
    15 pages
    English language
    sale 15% off
ASTM
ASTM F1346-23(Specification)
Standard Performance Specification for Safety Covers and Labeling Requirements for All Covers for Swimming Pools, Spas and Hot Tubs

SCOPE
1.1 This specification establishes requirements for safety covers for swimming pools, spas, hot tubs, and wading pools (hereinafter referred to as pools, unless otherwise specified). When correctly installed and used in accordance with the manufacturer's instructions, this specification is intended to reduce the risk of drowning by inhibiting the access of children under five years of age to the water.  
1.2 This specification includes performance tests to demonstrate the compliance or noncompliance to requirements herein stated for safety covers. It also includes marking requirements for all covers.  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 The following safety hazards caveat pertains only to the test methods section, Section 9, of this specification:  This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    7 pages
    English language
    sale 15% off
  • Technical specification
    7 pages
    English language
    sale 15% off
ASTM
ASTM F2959-23a(Practice)
Standard Practice for Aerial Adventure Courses

SIGNIFICANCE AND USE
4.1 The rational for developing a separate standard practice for Aerial Adventure Courses is based on the unique functional, operational and patron participation requirements when compared to amusement rides and devices.  
4.2 The purpose of this practice is to provide designers, manufacturers, constructors, system integrators, owners/operators, and auditors with criteria and references for use in the design, manufacture, construction, installation, integration, operation, maintenance, auditing, and major modification of Aerial Adventure Courses.  
4.3 Unless this practice expressly provides otherwise in a particular provision, the term “Aerial Adventure Course” is to be used in place of “Amusement Rides and Devices” herein.
SCOPE
1.1 This practice establishes criteria for the Design, Manufacture, Installation, Operation, Maintenance, Auditing and Major Modification of Aerial Adventure Courses.  
1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    28 pages
    English language
    sale 15% off
  • Standard
    28 pages
    English language
    sale 15% off
ASTM
ASTM F2461-23(Practice)
Standard Practice for Manufacture, Construction, Operation, and Maintenance of Aquatic Play Equipment

SCOPE
1.1 This practice covers information for manufacture, construction, operations and maintenance of aquatic play equipment and provides safety performance standards for various types of public aquatic play components and aquatic play composite structures.  
1.2 Inclusions:  
1.2.1 Climbable and climb-resistant aquatic play components, composite aquatic play structures, user controls, water sprays, fountains, and slides that occur on wet decks and wading, swimming or leisure pools. The play components specified herein occur for use in aquatic play areas.  
1.2.2 Play equipment, fall zones, use zones for wet decks, wading pools, swimming pools and leisure pools.  
1.2.3 This standard is intended to apply to Aquatic Play Equipment that is located in and around re- circulated and potable water recreational facilities. Such facilities include but are not limited to amusement parks, theme parks, water parks, family entertainment centers, municipal swimming pools and municipal parks.  
1.2.4 Waterslides 6 ft in height or smaller.  
1.3 Exclusions:  
1.3.1 Playground equipment that does not have an entry or an exit onto or into a wet deck, wading pool, swimming pool or aquatic recreation pool.  
1.3.2 Home playground or home pool equipment or play equipment as scoped in Consumer Safety Performance Specification F1148-21 and ANSI/NSPI-5.  
1.3.3 Waterslides as scoped in Practice F2376-22.  
1.3.4 Flotation devices used on water slides or in swimming pools.  
1.3.5 Swimming pools as specified by ANSI/NSPI-1 or ANSI/IAF-9.  
1.3.6 Products or facility elements specifically designed to provide access to and from pools for people with disabilities.  
1.3.7 Water rides such as log flumes, raft rides, inner tube rides, waterslides or other attractions where the participant sits in a vehicle or is physically propelled or moved by or with water.  
1.3.8 Sports equipment, fitness equipment, and diving equipment.  
1.4 Compliance:  
1.4.1 Where water is indirectly or directly added or applied to Consumer Safety Performance Specification F1487-21 play equipment, the equipment shall comply with this standard. Where a requirement for compliance to a section of the Consumer Safety Performance Specification F1487-21 standard is required by this standard, the section number is preceded with the standard's designation.  
1.4.2 Soft contained play structures with aquatic play components shall comply with Safety Performance Specification F1918-21 except as modified by this standard.  
1.4.3 Aquatic play components and composite play structures represented, as complying with this safety performance standard shall meet all applicable requirements specified herein. Anyone representing compliance with this standard shall keep such essential records as are necessary to document any claim that the requirements within this standard have been met.  
1.5 This standard includes the following sections:    
Scope  
Section 1  
Referenced Documents  
Section 2  
Terminology  
Section 3  
Manufacturing and Materials  
Section 4  
Design  
Section 5  
Performance Requirements  
Section 6  
Operator Responsibilities  
Section 7  
Manufacturer/Designer
Responsibilities  
Section 8  
Installer Responsibilities  
Section 9  
1.6 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. (The conversion factor from inch-pound to metric units is 1 in. = 25.4 mm, and 1 lb = 4.4482 N.)  
1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.8 This international standard was developed in accordance with intern...

  • Standard
    13 pages
    English language
    sale 15% off
  • Standard
    13 pages
    English language
    sale 15% off