iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM D912-81(1999)

(Specification)

Standard Specification for Cuprous Oxide for Use in Antifouling Paints (Withdrawn 2004)

Standard Specification for Cuprous Oxide for Use in Antifouling Paints (Withdrawn 2004)

SCOPE
1.1 This specification covers cuprous oxide for use in antifouling paints.
WITHDRAWN RATIONALE
DESIG: D912 81 (Reapproved 1999)
This specification covers cuprous oxide for use in antifouling paints.
Formerly under the jurisdiction of Committee D01 on Paint and Related Coatings, Materials, and Applications, this specification was withdrawn in November 2004. This standard is being withdrawn without replacement due to its limited use by industry.

General Information

Status
Withdrawn
Publication Date
09-May-1999
Withdrawal Date
08-Nov-2004
ICS
87.060.99 - Other paint ingredients
Technical Committee
D01 - Paint and Related Coatings, Materials, and Applications
Drafting Committee
D01.31 - Pigment Specifications
Current Stage
Ref Project

Buy Standard

ASTM D912-81(1999) - Standard Specification for Cuprous Oxide for Use in Antifouling Paints (Withdrawn 2004)ASTM D912-81(1999) - Standard Specification for Cuprous Oxide for Use in Antifouling Paints (Withdrawn 2004)
PreviousNext
Technical specification
ASTM D912-81(1999) - Standard Specification for Cuprous Oxide for Use in Antifouling Paints (Withdrawn 2004)
English language
1 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)


NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: D 912 – 81 (Reapproved 1999)
Standard Specification for
Cuprous Oxide for Use in Antifouling Paints
This standard is issued under the fixed designation D 912; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope
Coarse particles (total residue retained on a No. 325 (45-μm) 0.5
sieve), max, %
1.1 This specification covers cuprous oxide for use in
Total nitric acid insoluble residue on a No. 200 (75-μm) sieve, 0.1
antifouling paints.
max, %
4. Sampling
2. Referenced Documents
4.1 Two samples shall be taken at random from different
2.1 ASTM Standards:
packages from each lot, batch, day’s pack, or other unit of
D 185 Test Methods for Coarse Particles in Pigments,
production in a shipment. When no markings distinguishing
Pastes, and Paints
between units of production appear, samples shall be taken
D 283 Test Methods for Chemical Analysis of Cuprous
from different packages in the ratio of two samples for each
Oxide and Copper Pigments
10 000 lb (5000 kg), except that for shipments of less than
3. Composition
10 000 lb two samples shall be taken. At the option of the
purchaser, the samples may be tested separately or after
3.1 The pigment shall consist essentially of finely divided
cuprous oxide and shall conform to the following require- blending in equal quantities the samples from the same
production unit to form a composite sample.
ments:
Cuprous oxide, min, % 97
5. Test Methods
Total copper, calculated as Cu, min, % 86
Total reducing power as Cu O, min, % 97
5.1 Tests shall be conducted in accordance with the follow-
Metals other than copper, max, % 0.5
ing ASTM test methods. Test procedures not covered by ASTM
Combined chlorides, calculated as Cl, and sulfates, calculated 0.5
as SO , max, %
4 test methods shall be mutually agreed upon between the
Acet
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM D564-87(2023)(Test Method)
Standard Test Methods for Liquid Paint Driers

SIGNIFICANCE AND USE
3.1 Driers accelerate the drying of oil, paint, printing ink, and varnish.  
3.2 These test methods are applicable to liquid driers manufactured for use in paints and related coatings.  
3.3 The tests for metallic content using ethylenediaminetetraacetic acid dihydrate (EDTA) are intended for concentrated solutions of single metals; two or more metals may cause interference.
SCOPE
1.1 These test methods cover the test procedures to be applied to liquid paint driers used in paints and related coatings. Typical paint driers, listed in Specification D600, are carboxylates of lead, cobalt, manganese, zinc, iron, calcium, and zirconium.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM D3988-05(2023)(Test Method)
Standard Test Method for Vanadium in Paint Driers by EDTA Method

SIGNIFICANCE AND USE
4.1 This test method may be used to confirm the stated content of a pure liquid vanadium drier manufactured for use by the coatings industry.
SCOPE
1.1 This test method covers the titrimetric determination of vanadium in liquid vanadium driers and utilizes the disodium salt of ethylenediaminetetraacetic acid dihydrate (EDTA).  
1.2 This test method is limited to the determination of the vanadium content of a liquid vanadium drier that does not contain other drier elements. This test method is not applicable to drier blends.  
1.3 All cations that can be titrated with EDTA in alkaline media interfere and must not be present in the sample.  
1.4 This test method has been tested for concentrations of 3 % and 4 % vanadium, but there is no reason to believe that it is not suitable for higher or lower vanadium concentrations provided specimen size is adjusted proportionately.  
1.5 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM D3970-05(2023)(Test Method)
Standard Test Method for Cerium in Paint Driers by Oxidimetric Determination

SIGNIFICANCE AND USE
4.1 This test method may be used to confirm in the presence of rare earths the stated cerium content of liquid pure cerium or rare earth driers manufactured for use in the coatings industry.
SCOPE
1.1 This test method covers the titrimetric determination of cerium in liquid cerium and rare earth paint driers and utilizes ferrous ammonium sulfate.  
1.2 This test method is not applicable to dryer blends.  
1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For a specific hazard statement, see Section 7.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM D2613-01(2023)(Test Method)
Standard Test Method for Calcium or Zinc in Paint Driers by EDTA Method

SIGNIFICANCE AND USE
4.1 This test method may be used to confirm the stated calcium or zinc content of pure liquid calcium or zinc driers soluble in toluene-alcohol and manufactured for use by the coatings industry.
SCOPE
1.1 This test method covers a titrimetric determination of calcium in liquid calcium driers and zinc in liquid zinc driers that can be dissolved in a toluene-alcohol mixture and utilizes the disodium salt of ethylenediaminetetraacetic acid dihydrate (EDTA).  
1.2 This test method is not applicable to drier blends.  
1.3 All cations that can be titrated with EDTA in alkaline media interfere and must not be present in the sample.  
1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM D3804-02(2021)(Test Method)
Standard Test Method for Iron in Paint Driers by EDTA Method

SIGNIFICANCE AND USE
4.1 This test method may be used to confirm the stated content of a liquid iron drier soluble in isopropyl alcohol and manufactured for use in the coatings industry. The content determines activity level.
SCOPE
1.1 This test method covers the titrimetric determination of iron in liquid iron driers soluble in isopropyl alcohol and utilizes the disodium salt of ethylenediaminetetraacetic acid dihydrate (EDTA).  
1.2 This test method is limited to the determination of the iron content of a liquid drier that does not contain other drier elements. This method is not applicable to drier blends.  
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM D964-03(2020)(Specification)
Standard Specification for Metallic Copper Powder for Use in Antifouling Paints

ABSTRACT
This specification covers metallic copper powder for use in antifouling paints. The pigment shall consist essentially of finely divided copper metal. The copper, and coarse particle shall be tested to meet the requirements prescribed.
SCOPE
1.1 This specification covers copper powder for use in antifouling paints.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    1 page
    English language
    sale 15% off
ASTM
ASTM D267-82(2020)(Specification)
Standard Specification for Gold Bronze Powder

ABSTRACT
This specification covers the materials commercially known as gold bronze, pale gold bronze, and rich gold bronze powders. The gold bronze powder shall be made from new ingot metals, shall consist of fine polished flakes containing the prescribed percentage of fatty or oily matter (polishing lubricant), shall have the specified residue content and leafing properties, and shall be suitable for making gold bronze paint. The sampling and test methods to determine conformance to the specified composition and properties are given.
SCOPE
1.1 This specification covers the materials commercially known as gold bronze, pale gold bronze, and rich gold bronze powders.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off
ASTM
ASTM D3989-01(2019)e1(Test Method)
Standard Test Method for Total Rare Earth Metals in Paint Driers by EDTA Method

SIGNIFICANCE AND USE
4.1 This test method may be used to confirm the stated content of a pure, liquid rare earth metal drier manufactured for use in the coatings industry.
SCOPE
1.1 This test method covers the titrimetric determination of rare earth metals in liquid rare earth metal driers and utilizes the disodium salt of ethylenediaminetetraacetic acid dihydrate (EDTA).  
1.2 This test method is limited to the determination of the rare earth metal content of a liquid rare earth metal drier that does not contain other drier elements. The method is not applicable to drier blends.  
1.3 This test method has been tested in concentrations of 6 % cerium and 6 % rare earth metals, but there is no reason to believe that it is not suitable for higher or lower drier metal concentrations provided specimen size is adjusted accordingly.  
1.4 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM D3969-01(2019)e1(Test Method)
Standard Test Method for Zirconium in Paint Driers by EDTA Method

SIGNIFICANCE AND USE
4.1 The amount of zirconium drier used in oxidizing-type coatings significantly affects their drying properties. This test method may be used to confirm the stated content of a pure liquid zirconium drier manufactured for use by the coatings industry.
SCOPE
1.1 This test method covers the titrimetric determination of zirconium in zirconium driers used in the coatings industry and utilizes the disodium salt of ethylenediaminetetraacetic acid dihydrate (EDTA).  
1.2 This test method is limited to the determination of the zirconium content of a liquid zirconium drier that does not contain other drier elements. The test method is not applicable to drier blends and does not differentiate hafnium from zirconium.  
1.3 All cations that can be titrated with EDTA in acid media interfere and must not be present in the sample.  
1.4 This test method has been tested for concentrations of 6 and 12 % zirconium, but there is no reason to believe that it is not suitable for higher or lower zirconium concentrations, provided specimen size is adjusted proportionately.  
1.5 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM D4140-07(2018)(Guide)
Standard Guide for Determining Volatile and Nonvolatile Content of Driers, Drying Oils, Naval Stores, and Solvents

SIGNIFICANCE AND USE
4.1 The nonvolatile content of raw materials may be used to determine the total nonvolatile content (solids) of paint and related coatings. Such information may be useful to coatings producers and users for the determination of the total solids available for film formation and for the estimation of the volatile organic content.
SCOPE
1.1 This guide is intended to aid in the selection of the proper ASTM test method for determining the volatile and nonvolatile content of driers, drying oils, naval stores, and solvents.  
Note 1: Test methods for determining the composition of the volatile fraction are not covered by this guide.  
1.2 The test methods included are as follows:    
Standard  
Section  
ASTM Designation  
Driers  
5.1  
D1644  
Drying oils  
5.2  
D555
D1960  
Naval stores  
5.3  
D233
D889
D1131  
Solvents  
5.4  
D1353  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    2 pages
    English language
    sale 15% off