Standard Classification for Abuse-Resistant Nondecorated Interior Gypsum Panel Products and Fiber-Reinforced Cement Panels

SIGNIFICANCE AND USE
4.1 Each abuse/impact property of abuse resistant wall panels is divided into three classification levels. The three levels of classification are: Level I, Level II, and Level III, with Level I representing the lowest rating for any given property. The test methods specified are utilized to establish the abuse-resistance classification of an abuse resistant wall panel. Each classification level requires a minimum overall specified performance. Any classified abuse resistant wall panel can be used at a classification level which is rated lower than the highest level qualified.
SCOPE
1.1 This standard establishes classifications of abuse resistance based on the abrasion resistance and impact resistance performance of nondecorated interior gypsum panel products and fiber-reinforced cement panels (abuse resistant wall panels).  
1.1.1 This standard is a method of classifying gypsum panel product performance and is not intended to classify systems for abuse resistance.  
1.2 The values stated in inch-pound and SI (metric) units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system shall be used independent of the other. Values from the two systems shall not be combined.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

General Information

Status
Historical
Publication Date
14-Jul-2018
Current Stage
Ref Project

Relations

Buy Standard

Standard
ASTM C1629/C1629M-18a - Standard Classification for Abuse-Resistant Nondecorated Interior Gypsum Panel Products and Fiber-Reinforced Cement Panels
English language
11 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
REDLINE ASTM C1629/C1629M-18a - Standard Classification for Abuse-Resistant Nondecorated Interior Gypsum Panel Products and Fiber-Reinforced Cement Panels
English language
11 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:C1629/C1629M −18a
Standard Classification for
Abuse-Resistant Nondecorated Interior Gypsum Panel
1
Products and Fiber-Reinforced Cement Panels
This standard is issued under the fixed designation C1629/C1629M; the number immediately following the designation indicates the
year of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last
reapproval. A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* C840SpecificationforApplicationandFinishingofGypsum
Board
1.1 This standard establishes classifications of abuse resis-
C1154Terminology for Non-Asbestos Fiber-Reinforced Ce-
tance based on the abrasion resistance and impact resistance
ment Products
performance of nondecorated interior gypsum panel products
D1517Terminology Relating to Leather
and fiber-reinforced cement panels (abuse resistant wall pan-
D4977/D4977MTest Method for GranuleAdhesion to Min-
els).
eral Surfaced Roofing by Abrasion
1.1.1 Thisstandardisamethodofclassifyinggypsumpanel
D5420Test Method for Impact Resistance of Flat, Rigid
productperformanceandisnotintendedtoclassifysystemsfor
Plastic Specimen by Means of a Striker Impacted by a
abuse resistance.
Falling Weight (Gardner Impact)
1.2 Thevaluesstatedininch-poundandSI(metric)unitsare
2.2 ISO Document:
to be regarded separately as standard. Within the text, the SI
ISO 6707-1Building and Civil Engineering—Vocabulary—
units are shown in brackets. The values stated in each system
Part 1: General Terms
shall be used independent of the other. Values from the two
systems shall not be combined. 2.3 Federal Specification:
A-A-50197AThread, Linen
1.3 This standard does not purport to address all of the
safety concerns, if any, associated with its use. It is the
2.4 Voluntary Product Standard:
responsibility of the user of this standard to establish appro-
PS20American Softwood Lumber Standard
priate safety, health, and environmental practices and deter-
mine the applicability of regulatory limitations prior to use.
3. Terminology
1.4 This international standard was developed in accor-
3.1 Definitions of terms shall be in accordance with Termi-
dance with internationally recognized principles on standard-
nologies C11 and C1154.
ization established in the Decision on Principles for the
3.2 Definitions of Terms Specific to This Standard:
Development of International Standards, Guides and Recom-
3.2.1 failure (hard body impact), n—test result constituted
mendations issued by the World Trade Organization Technical
by the penetration or deformation of the wall cavity by the
Barriers to Trade (TBT) Committee.
impact head establishing a residual deflection of the panel
2. Referenced Documents
exceeding the nominal thickness of the test panel.
2
3.2.2 structural failure (soft body impact), n—a test result
2.1 ASTM Standards:
C11Terminology Relating to Gypsum and Related Building constitutedbythepenetrationordeformationofthewallcavity
by the soft body impact bag establishing a residual deflection
Materials and Systems
C473Test Methods for Physical Testing of Gypsum Panel ofanyareaonthetestpanelthatexceedsthenominalthickness
of the test panel.
Products
3.2.2.1 deformation, n—change of shape or dimension or
both. ISO 6707-1
1
This classification is under the jurisdiction of ASTM Committee C11 on
GypsumandRelatedBuildingMaterialsandSystemsandisthedirectresponsibility 3.2.2.2 surface damage, n—pulverization of the core of the
of Subcommittee C11.01 on Specifications andTest Methods for Gypsum Products.
test panel at the point of impact, which is evidenced by
Current edition approved July 15, 2018. Published November 2018. Originally
cracking, creasing, or other visible damage short of failure as
approved in 2005. Last previous edition approved in 2018 as C1629/C1629M–18.
defined in 3.2.2.
DOI: 10.1520/C1629_C1629M-18A.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
3.2.3 residual deflection, n—permanent deformation of a
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
building element, component, or structure after removal of
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website. applied force.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
C1629/C1629M−18a
TABLE 3 Performance Requirements
3.2.3.1 Discussion—Also called permanent set or residual
Soft Body Impact Test
deformation.
Soft Body
Classification
Minimum
4. Significance and Use
Level
ft-lbf [J]
4.1 Each abuse/impact property of abuse resistant wall
1 90 [122]
panels is divided into three classificatio
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: C1629/C1629M − 18 C1629/C1629M − 18a
Standard Classification for
Abuse-Resistant Nondecorated Interior Gypsum Panel
1
Products and Fiber-Reinforced Cement Panels
This standard is issued under the fixed designation C1629/C1629M; the number immediately following the designation indicates the
year of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last
reapproval. A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope*
1.1 This standard establishes classifications of abuse resistance based on the abrasion resistance and impact resistance
performance of nondecorated interior gypsum panel products and fiber-reinforced cement panels (abuse resistant wall panels).
1.1.1 This standard is a method of classifying gypsum panel product performance and is not intended to classify systems for
abuse resistance.
1.2 The values stated in inch-pound and SI (metric) units are to be regarded separately as standard. Within the text, the SI units
are shown in brackets. The values stated in each system shall be used independent of the other. Values from the two systems shall
not be combined.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of
regulatory limitations prior to use.
1.4 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2
2.1 ASTM Standards:
C11 Terminology Relating to Gypsum and Related Building Materials and Systems
C473 Test Methods for Physical Testing of Gypsum Panel Products
C840 Specification for Application and Finishing of Gypsum Board
C1154 Terminology for Non-Asbestos Fiber-Reinforced Cement Products
D1517 Terminology Relating to Leather
D4977D4977/D4977M Test Method for Granule Adhesion to Mineral Surfaced Roofing by Abrasion
D5420 Test Method for Impact Resistance of Flat, Rigid Plastic Specimen by Means of a Striker Impacted by a Falling Weight
(Gardner Impact)
E695 Test Method of Measuring Relative Resistance of Wall, Floor, and Roof Construction to Impact Loading
2.2 ISO Documents:Document:
ISO 6707-1 Building and Civil Engineering—Vocabulary—Part 1: General Terms
2.3 Federal Specification:
A-A-50197A Thread, Linen
2.4 Voluntary Product Standard:
PS20 American Softwood Lumber Standard
3. Terminology
3.1 Definitions of terms shall be in accordance with Terminologies C11 and C1154.
3.2 Definitions of Terms Specific to This Standard:
1
This classification is under the jurisdiction of ASTM Committee C11 on Gypsum and Related Building Materials and Systems and is the direct responsibility of
Subcommittee C11.01 on Specifications and Test Methods for Gypsum Products.
Current edition approved June 1, 2018July 15, 2018. Published July 2018November 2018. Originally approved in 2005. Last previous edition approved in 20152018 as
C1629/C1629M – 15.C1629/C1629M – 18. DOI: 10.1520/C1629_C1629M-18.10.1520/C1629_C1629M-18A.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
C1629/C1629M − 18a
3.2.1 failure (hard body impact), n—test result constituted by the penetration or deformation of the wall cavity by the impact
head establishing a residual deflection of the panel exceeding the nominal thickness of the test panel.
3.2.2 structural failure (soft body impact), n—a test result constituted by the penetration or deformation of the wall cavity by
the soft body impact bag establishing a residual deflection of any area on the test panel that exceeds the nominal thickness of the
test panel.
3.2.2.1 deformation, n—change of shape or dimension or both. ISO 6707-1
3.2.2.2 surface damage, n—pulverization of the core of the test panel at the point of
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.