ASTM F467M-06a

Standard Specification for Nonferrous Nuts for General Use [Metric]

SCOPE
1.1 This specification covers the requirements for commercial wrought nonferrous nuts in nominal thread diameters M6 to M36 inclusive in a number of alloys in common use and intended for general service applications.
1.2 Applicable bolts, cap screws, and studs for use with nuts covered by this specification are covered by Specification F 468M. Note 1 - This specification is the metric companion of Specification F 467.

General Information

• Status: Historical
• Publication Date: 31-Jul-2006
• ICS: 21.060.20 - Nuts
• Technical Committee: F16 - Fasteners
• Drafting Committee: F16.04 - Nonferrous Fasteners

Relations

• Replaces: ASTM F467M-06 - Standard Specification for Nonferrous Nuts for General Use [Metric]
• Effective Date: 01-Aug-2006
• Referred By: ASTM F468M-06(2018) - Standard Specification for Nonferrous Bolts, Hex Cap Screws, and Studs for General Use (Metric)
• Effective Date: 01-Aug-2006
• Referred By: ASTM B746/B746M-22 - Standard Specification for Corrugated Aluminum Alloy Structural Plate for Field-Bolted Pipe, Pipe-Arches, and Arches
• Effective Date: 01-Aug-2006
• Referred By: ASTM B745/B745M-15(2021) - Standard Specification for Corrugated Aluminum Pipe for Sewers and Drains
• Effective Date: 01-Aug-2006

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: F 467M – 06a
METRIC
Standard Specification for
1
Nonferrous Nuts for General Use [Metric]
This standard is issued under the fixed designation F 467M; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope* E 54 Test Methods for Chemical Analysis of Special
3
Brasses and Bronzes
1.1 This specification covers the requirements for commer-
E55 PracticeforSamplingWroughtNonferrousMetalsand
cial wrought nonferrous nuts in nominal thread diameters M6
Alloys for Determination of Chemical Composition
to M36 inclusive in a number of alloys in common use and
E 62 Test Methods for Chemical Analysis of Copper and
intended for general service applications.
Copper Alloys (Photometric Methods)
1.2 Applicablebolts,capscrews,andstudsforusewithnuts
E 75 Test Methods for ChemicalAnalysis of Copper-Nickel
covered by this specification are covered by Specification
and Copper-Nickel-Zinc Alloys
F 468M.
E 76 Test Methods for ChemicalAnalysis of Nickel-Copper
NOTE 1—This specification is the metric companion of Specification 3
Alloys
F 467.
E92 Test Method for Vickers Hardness of Metallic Mate-
rials
2. Referenced Documents
E 101 Test Method for Spectrographic Analysis of Alu-
2
2.1 ASTM Standards:
minum and Aluminum Alloys by the Point-to-Plane Tech-
B 154 Test Method for Mercurous Nitrate Test for Copper
3
nique
Alloys
E 120 Test Methods for ChemicalAnalysis of Titanium and
B 574 Specification for Low-Carbon Nickel-Chromium-
3
Titanium Alloys
Molybdenum, Low-Carbon Nickel-Molybdenum-
E 165 Test Method for Liquid Penetrant Examination
Chromium-Tantalum, Low-Carbon Nickel-Chromium-
E 227 Test Method for Optical Emission Spectrometric
Molybdenum-Copper, and Low-Carbon Nickel-
Analysis of Aluminum and Aluminum Alloys by the
Chromium-Molybdenum-Tungsten Alloy Rod
3
Point-to-Plane Technique
D 3951 Practice for Commercial Packaging
E 354 Test Methods for Chemical Analysis of High-
E18 Test Methods for Rockwell Hardness and Rockwell
Temperature, Electrical, Magnetic, and Other Similar Iron,
Superficial Hardness of Metallic Materials
Nickel, and Cobalt Alloys
E29 Practice for Using Significant Digits in Test Data to
E 478 Test Methods for Chemical Analysis of Copper
Determine Conformance with Specifications
Alloys
E 34 Test Methods for ChemicalAnalysis ofAluminum and
E 1409 Test Method for Determination of Oxygen and
Aluminum-Base Alloys
Nitrogen in Titanium and TitaniumAlloys by the Inert Gas
E 38 Methods for Chemical Analysis of Nickel-Chromium
Fusion Technique
3
and Nickel-Chromium-Iron Alloys
F 468M Specification for Nonferrous Bolts, Hex Cap
E 53 Test Method for Determination of Copper in Unal-
Screws, and Studs for General Use [Metric]
loyed Copper by Gravimetry
F 606M Test Methods for Determining the Mechanical
Properties of Externally and InternallyThreaded Fasteners,
1
Washers, and Rivets [Metric]
This specification is under the jurisdiction of ASTM Committee F16 on
Fasteners and is the direct responsibility of Subcommittee F16.04 on Nonferrous F 1470 GuideforFastenerSamplingforSpecifiedMechani-
Fasteners.
cal Properties and Performance Inspection
Current edition approved Aug. 1, 2006. Published August 2006. Originally
4
2.2 ASME Standards:
approved in 1979. Last previous edition approved in 2006 as F 467M – 06.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM
Standards volume information, refer to the standard’s Document Summary page on
4
the ASTM website. Available from Global Engineering Documents, 15 Inverness Way, East
3
Withdrawn. Englewood, CO 80112-5704, http://global.ihs.com.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
F 467M – 06a
B 1.13M Metric Screw Threads facturer shall make individual analyses of randomly selected
B 18.2.4.1M Metric Hex Nuts, Style 1 nutsfromtheproducttobeshippedandreporttheresultstothe
purchaser. Alternatively, if heat and lot identities have been
3. Ordering Information maintained, the analysis of the raw material from which the
nuts have been manufactured may be reported instead of
3.1 Orders for nuts under this specification shall include the
product analysis.
following information:
5.2.2 For aluminum nuts, instead of 5.2.1, the manufacturer
3.1.1 Quantity (numbers of pieces of each item and size);
may furnish
...

This document is not anASTM standard and is intended only to provide the user of anASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:F467M–06 Designation: F 467M – 06a
Standard Specification for
1
Nonferrous Nuts for General Use [Metric]
This standard is issued under the fixed designation F 467M; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope*
1.1 This specification covers the requirements for commercial wrought nonferrous nuts in nominal thread diameters M6 to M36
inclusive in a number of alloys in common use and intended for general service applications.
1.2 Applicable bolts, cap screws, and studs for use with nuts covered by this specification are covered by Specification F 468M.
NOTE 1—This specification is the metric companion of Specification F 467.
2. Referenced Documents
2
2.1 ASTM Standards:
B 154 Test Method for Mercurous Nitrate Test for Copper Alloys
B574 Specification for Low-Carbon Nickel-Chromium-Molybdenum, Low-Carbon Nickel-Molybdenum-Chromium-
Tantalum, Low-Carbon Nickel-Chromium-Molybdenum-Copper, and Low-Carbon Nickel-Chromium-Molybdenum-Tungsten
Alloy Rod
D 3951 Practice for Commercial Packaging
E18 Test Methods for Rockwell Hardness of Metallic Materials
E29 Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
E34 Test Methods for Chemical Analysis of Aluminum and Aluminum-Base Alloys
3
E38 Methods for Chemical Analysis of Nickel-Chromium and Nickel-Chromium-Iron Alloys
E53 Test Method for Determination of Copper in Unalloyed Copper by Gravimetry
E54 Test Methods for Chemical Analysis of Special Brasses and Bronzes
E55 Practice for Sampling Wrought Nonferrous Metals and Alloys for Determination of Chemical Composition
E62 Test Methods for Chemical Analysis of Copper and Copper Alloys (Photometric Methods)
E75 Test Methods for Chemical Analysis of Copper-Nickel and Copper-Nickel-Zinc Alloys
E76 Test Methods for Chemical Analysis of Nickel-Copper Alloys
E92 Test Method for Vickers Hardness of Metallic Materials
0
E 101 Test Method for Spectrographic Analysis of Alu-minum and Aluminum Alloys by the Point-to-Plane Technique
E 120 Test Methods for Chemical Analysis of Titanium and Titanium Alloys
E 165 Test Method for Liquid Penetrant Examination
E 227 Test Method for Optical Emission Spectrometric Analysis of Aluminum and Aluminum Alloys by the Point-to-Plane
Technique
E 354 Test Methods for Chemical Analysis of High-Temperature, Electrical, Magnetic, and Other Similar Iron, Nickel, and
Cobalt Alloys
E 478 Test Methods for Chemical Analysis of Copper Alloys
E 1409 Test Method for Determination of Oxygen and Nitrogen in Titanium and Titanium Alloys by the Inert Gas Fusion
Technique
F 468M Specification for Nonferrous Bolts, Hex Cap Screws, and Studs for General Use (Metric)
F 606M Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers,
and Rivets (Metric)
F 1470 Practice for Fastener Sampling for Specified Mechanical Properties and Performance Inspection
1
This specification is under the jurisdiction of ASTM Committee F16 on Fasteners and is the direct responsibility of Subcommittee F16.04 on Nonferrous Fasteners .
Current edition approved MayAug. 1, 2006. Published MayAugust 2006. Originally approved in 1979. Last previous edition approved in 20052006 as F 467M – 056.
2
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at [e-mail]. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
3
Withdrawn.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
F 467M – 06a
4
2.2 ASME Standards:
B 1.13M Metric Screw Threads
B 18.2.4.1M Metric Hex Nuts, Style 1
3. Ordering Information
3.1 Orders for nuts under this specification shall include the following information:
3.1.1 Quantity (numbers of pieces of each item and size);
3.1.2 Name of item;
3.1.3 Nominal thread diameter and thread pitch;
3.1.4 Alloy number (Table 1);
3.1.5 Stress relieving, if required (4.2.3);
3.1.6 “Shipment lot” testing, as required (Section 9);
3.1.7 Source inspection, if required
...