ASTM F2620-20ae1
(Practice)Standard Practice for Heat Fusion Joining of Polyethylene Pipe and Fittings
Standard Practice for Heat Fusion Joining of Polyethylene Pipe and Fittings
SIGNIFICANCE AND USE
4.1 The procedures described in Sections 7 – 9 are primarily intended for (but not limited to) field joining of polyethylene (PE) pipe and fittings, using suitable equipment and appropriate environmental control procedures. When properly implemented, strong pressure/leak-tight joints are produced. When these joints are destructively tested, the failure occurs outside the fusion joined area.
4.2 Melt characteristics, average molecular weight and molecular weight distribution are influential factors in establishing suitable fusion parameters; therefore, consider the manufacturer’s instructions in the use or development of a specific fusion procedure. See Annex A1.
4.3 The socket fusion, butt fusion, and saddle fusion procedures in this practice are suitable for joining PE gas pipe and fittings, PE water pipe and fittings, and PE general purpose pipes and fittings made to PE product specifications from organizations such as ASTM, AWWA, API, and ISO that are used in pressure, low pressure and non-pressure applications. For gas applications, qualification of the procedure by testing joints made using the procedure in accordance with regulations from the authority having jurisdiction are required.
SCOPE
1.1 This practice describes procedures for making joints with polyethylene (PE) pipe and fittings by means of heat fusion joining in, but not limited to, a field environment. Other suitable heat fusion joining procedures are available from various sources including pipe and fitting manufacturers. This practice does not purport to address all possible heat fusion joining procedures, or to preclude the use of qualified procedures developed by other parties that have been proved to produce reliable heat fusion joints.
1.2 The parameters and procedures are applicable only to joining polyethylene pipe and fittings of related polymer chemistry. They are intended for PE fuel gas pipe in accordance with Specification D2513 and PE potable water, sewer and industrial pipe manufactured in accordance with Specification F714, Specification D3035, and AWWA C901 and C906. Consult with the pipe manufacturers to make sure they approve this procedure for the pipe to be joined (see Appendix X1).
Note 1: The parameters and procedures shown for Section 8. Procedure 2—Butt Fusion, were developed and validated using testing documented in Plastic Pipe Institute (PPI) TR-33. The parameters and procedures shown in Section 9. Procedure 3— Saddle Fusion, were developed and validated using testing documented in PPI TR-41.
Note 2: Information about polyethylene pipe and fittings that have related polymer chemistry is presented in Plastics Pipe Institute (PPI) TR-33 and TR-41.
1.3 Parts that are within the dimensional tolerances given in present ASTM specifications are required to produce sound joints between polyethylene pipe and fittings when using the joining techniques described in this practice.
1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.5 The text of this practice references notes, footnotes, and appendixes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the practice.
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade O...
General Information
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
´1
Designation: F2620 − 20a An American National Standard
Standard Practice for
1
Heat Fusion Joining of Polyethylene Pipe and Fittings
This standard is issued under the fixed designation F2620; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1
ε NOTE—Table 2 was editorially corrected for clarity in October 2021.
1. Scope* and footnotes (excluding those in tables and figures) shall not
be considered as requirements of the practice.
1.1 This practice describes procedures for making joints
1.6 This standard does not purport to address all of the
with polyethylene (PE) pipe and fittings by means of heat
safety concerns, if any, associated with its use. It is the
fusion joining in, but not limited to, a field environment. Other
responsibility of the user of this standard to establish appro-
suitable heat fusion joining procedures are available from
priate safety, health, and environmental practices and deter-
various sources including pipe and fitting manufacturers. This
mine the applicability of regulatory limitations prior to use.
practice does not purport to address all possible heat fusion
1.7 This international standard was developed in accor-
joining procedures, or to preclude the use of qualified proce-
dance with internationally recognized principles on standard-
dures developed by other parties that have been proved to
ization established in the Decision on Principles for the
produce reliable heat fusion joints.
Development of International Standards, Guides and Recom-
1.2 The parameters and procedures are applicable only to
mendations issued by the World Trade Organization Technical
joining polyethylene pipe and fittings of related polymer
Barriers to Trade (TBT) Committee.
chemistry. They are intended for PE fuel gas pipe in accor-
dance with Specification D2513 and PE potable water, sewer
2. Referenced Documents
and industrial pipe manufactured in accordance with Specifi-
2
2.1 ASTM Standards:
cation F714, Specification D3035, and AWWA C901 and
D2513 Specification for Polyethylene (PE) Gas Pressure
C906. Consult with the pipe manufacturers to make sure they
Pipe, Tubing, and Fittings
approve this procedure for the pipe to be joined (see Appendix
D3035 SpecificationforPolyethylene(PE)PlasticPipe(DR-
X1).
PR) Based on Controlled Outside Diameter
NOTE 1—The parameters and procedures shown for Section 8. Proce-
F714 Specification for Polyethylene (PE) Plastic Pipe (DR-
dure 2—Butt Fusion, were developed and validated using testing docu-
mented in Plastic Pipe Institute (PPI) TR-33. The parameters and
PR) Based on Outside Diameter
procedures shown in Section 9. Procedure 3— Saddle Fusion, were
F1056 Specification for Socket Fusion Tools for Use in
developed and validated using testing documented in PPI TR-41.
Socket Fusion Joining Polyethylene Pipe or Tubing and
NOTE 2—Information about polyethylene pipe and fittings that have
Fittings
related polymer chemistry is presented in Plastics Pipe Institute (PPI)
TR-33 and TR-41. F3124 Practice for Data Recording the Procedure used to
Produce Heat Butt Fusion Joints in Plastic Piping Systems
1.3 Parts that are within the dimensional tolerances given in
or Fittings
present ASTM specifications are required to produce sound
F3183 Practice for Guided Side Bend Evaluation of Poly-
joints between polyethylene pipe and fittings when using the
ethylene Pipe Butt Fusion Joint
joining techniques described in this practice.
F3190 Practice for Heat Fusion Equipment (HFE) Operator
1.4 The values stated in inch-pound units are to be regarded
Qualification on Polyethylene (PE) and Polyamide (PA)
as standard. The values given in parentheses are mathematical
Pipe and Fittings
conversions to SI units that are provided for information only
2.2 PPI Documents:
and are not considered standard.
TR-33 Generic Butt Fusion Joining Procedure for Field
3
1.5 The text of this practice references notes, footnotes, and Joining of Polyethylene
appendixes which provide explanatory material. These notes
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
1
This practice is under the jurisdiction of ASTM Committee F17 on Plastic contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
Piping Systems and is the direct responsibility of Subcommittee F17.20 on Joining. Standards volume information, refer to the standard’s Document Summary page on
Current edition approved Dec. 1, 2020. Published October 2021. Originally the ASTM website.
3
approved in 2006. Last previous edition approved in 2020 as F2620 – 20. DOI: Available from Plastics Pipe Institute (PPI), 105 Dec
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
´1
Designation: F2620 − 20a F2620 − 20a An American National Standard
Standard Practice for
1
Heat Fusion Joining of Polyethylene Pipe and Fittings
This standard is issued under the fixed designation F2620; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1
ε NOTE—Table 2 was editorially corrected for clarity in October 2021.
1. Scope*
1.1 This practice describes procedures for making joints with polyethylene (PE) pipe and fittings by means of heat fusion joining
in, but not limited to, a field environment. Other suitable heat fusion joining procedures are available from various sources
including pipe and fitting manufacturers. This practice does not purport to address all possible heat fusion joining procedures, or
to preclude the use of qualified procedures developed by other parties that have been proved to produce reliable heat fusion joints.
1.2 The parameters and procedures are applicable only to joining polyethylene pipe and fittings of related polymer chemistry. They
are intended for PE fuel gas pipe in accordance with Specification D2513 and PE potable water, sewer and industrial pipe
manufactured in accordance with Specification F714, Specification D3035, and AWWA C901 and C906. Consult with the pipe
manufacturers to make sure they approve this procedure for the pipe to be joined (see Appendix X1).
NOTE 1—The parameters and procedures shown for Section 8. Procedure 2—Butt Fusion, were developed and validated using testing documented in
Plastic Pipe Institute (PPI) TR-33. The parameters and procedures shown in Section 9. Procedure 3— Saddle Fusion, were developed and validated using
testing documented in PPI TR-41.
NOTE 2—Information about polyethylene pipe and fittings that have related polymer chemistry is presented in Plastics Pipe Institute (PPI) TR-33 and
TR-41.
1.3 Parts that are within the dimensional tolerances given in present ASTM specifications are required to produce sound joints
between polyethylene pipe and fittings when using the joining techniques described in this practice.
1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
1.5 The text of this practice references notes, footnotes, and appendixes which provide explanatory material. These notes and
footnotes (excluding those in tables and figures) shall not be considered as requirements of the practice.
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of
regulatory limitations prior to use.
1.7 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
1
This practice is under the jurisdiction of ASTM Committee F17 on Plastic Piping Systems and is the direct responsibility of Subcommittee F17.20 on Joining.
Current edition approved Dec. 1, 2020. Published October 2021. Originally approved in 2006. Last previous edition approved in 2020 as F2620 – 20. DOI:
10.1520/F2620-20A.10.1520/F2620-20AE01.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
´1
F2620 − 20a
2. Referenced Documents
2
2.1 ASTM Standards:
D2513 Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings
D3035 Specification for Polyethylene (PE) Plastic Pipe (DR-PR) Based on Controlled Outside Diameter
F714 Specification for Polyethylene (PE) Plastic Pipe (DR-PR) Based on Outside Diameter
F1056 Specification for Socket Fusion Tools for Use in Socket Fusion Joining Polyethylene Pipe or Tubing and Fittings
F3124 Practice for Data Recording the Procedure used to Produce Heat Butt Fusion Joints in Plastic Piping Systems or Fittings
F3183 Practice for Guided Side Bend Evaluat
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.