ASTM A562/A562M-10
(Specification)Standard Specification for Pressure Vessel Plates, Carbon Steel, Manganese-Titanium for Glass or Diffused Metallic Coatings
Standard Specification for Pressure Vessel Plates, Carbon Steel, Manganese-Titanium for Glass or Diffused Metallic Coatings
ABSTRACT
This specification covers standard requirements for titanium-bearing carbon steel plates intended for welded glass lined pressure vessels or other applications where the presence of free-iron carbide would be deleterious to the coating. The steel shall be killed and thermally treated to produce the required grain refinement specification. Heat and product analyses shall be performed wherein the material shall conform to the required chemical composition for carbon, manganese, phosphorus, sulfur, silicon, copper, and titanium. The steel plate shall conform to tensile requirements such as tensile strength, yield strength, and elongation.
SCOPE
1.1 This specification covers titanium-bearing carbon steel plates intended for welded glass lined pressure vessels or other applications where the presence of free-iron carbide would be deleterious to the coating. A minimum specific ratio of titanium to carbon is specified.
1.2 The maximum thickness of plates is limited to 2 in. [50 mm].
1.3 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: A562/A562M −10
StandardSpecification for
Pressure Vessel Plates, Carbon Steel, Manganese-Titanium
1
for Glass or Diffused Metallic Coatings
This standard is issued under the fixed designationA562/A562M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* 3. General Requirements and Ordering Information
2
3.1 Material supplied to this material specification shall
1.1 This specification covers titanium-bearing carbon steel
conform to Specification A20/A20M. These requirements out-
plates intended for welded glass lined pressure vessels or other
line the testing and retesting methods and procedures, permit-
applications where the presence of free-iron carbide would be
ted variations in dimensions, and mass, quality and repair of
deleterioustothecoating.Aminimumspecificratiooftitanium
defects, marking, loading, and ordering information.
to carbon is specified.
3.2 In addition to the basic requirements of this
1.2 The maximum thickness of plates is limited to 2 in. [50
specification, certain supplementary requirements are available
mm].
when additional control, testing, or examination is required to
1.3 The values stated in either inch-pound units or SI units
meet end use requirements.
are to be regarded separately as standard. Within the text, the
3.3 If the requirements of this specification are in conflict
SI units are shown in brackets. The values stated in each
with the requirements of Specification A20/A20M, the require-
system are not exact equivalents; therefore, each system must
ments of this specification shall prevail.
be used independently of the other. Combining values from the
4. Manufacture
two systems may result in nonconformance with the specifi-
cation.
4.1 Steelmaking Practice—The steel shall be killed.
5. Heat Treatment
2. Referenced Documents
5.1 Plates shall be thermally treated to produce grain
3
2.1 ASTM Standards:
refinement, either by normalizing or heating uniformly for hot
A20/A20M SpecificationforGeneralRequirementsforSteel
forming at a minimum temperature of 1600°F [870°C] or some
Plates for Pressure Vessels
higher agreed temperature, and held at this temperature for a
minimum of 1 h/in. [2.4 min/mm] of thickness.
6. Chemical Requirements
1
This specification is under the jurisdiction of ASTM Committee A01 on Steel,
Stainless Steel and Related Alloys and is the direct responsibility of Subcommittee 6.1 The steel shall conform to the chemical requirements
A01.11 on Steel Plates for Boilers and Pressure Vessels.
shown in Table 1 unless otherwise modified in accordance with
Current edition approved Oct. 1, 2010. Published November 2010. Originally
Supplementary Requirement S17, Vacuum Carbon-Deoxidized
approved in 1966. Last previous edition approved in 2006 as A562/A562M – 06.
Steel, in Specification A20/A20M.
DOI: 10.1520/A0562_A0562M-10.
2
For ASME Boiler and Pressure Vessel Code applications, see related Specifi-
7. Mechanical Requirements
cation SA-562/SA-562M in Section II of that Code.
3
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
7.1 Tension Test Requirements—The material as represented
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
by the tension
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:A562/A562M–06 Designation: A562/A562M – 10
Standard Specification for
Pressure Vessel Plates, Carbon Steel, Manganese-Titanium
1
for Glass or Diffused Metallic Coatings
This standard is issued under the fixed designationA562/A562M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope*
2
1.1 This specification covers titanium-bearing carbon steel plates intended for welded glass lined pressure vessels or other
applications where the presence of free-iron carbide would be deleterious to the coating. A minimum specific ratio of titanium to
carbon is specified.
1.2 The maximum thickness of plates is limited to 2 in. [50 mm].
1.3 Thevaluesstatedineitherinch-poundunitsorSIunitsaretoberegardedseparatelyasstandard.Withinthetext,theSIunits
are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used
independently of the other. Combining values from the two systems may result in nonconformance with the specification.
2. Referenced Documents
3
2.1 ASTM Standards:
A20/A20M Specification for General Requirements for Steel Plates for Pressure Vessels
3. General Requirements and Ordering Information
3.1 Material supplied to this material specification shall conform to Specification A20/A20M. These requirements outline the
testing and retesting methods and procedures, permissible variations in dimensions, and mass, quality and repair of defects,
marking, loading, etc.
3.2Specification . These requirements outline the testing and retesting methods and procedures, permitted variations in
dimensions, and mass, quality and repair of defects, marking, loading, and ordering information.
3.2 In addition to the basic requirements of this specification, certain supplementary requirements are available when additional
control, testing, or examination is required to meet end use requirements.
3.3 If the requirements of this specification are in conflict with the requirements of SpecificationA20/A20Malso establishes the
rules for the ordering information which should be complied with when purchasing material to this specification.
3.3In addition to the basic requirements of this specification, certain supplementary requirements are available when additional
control, testing, or examination is required to meet end use requirements. These include:
3.3.1Vacuum treatment,
3.3.2Additional or special tension testing,
3.3.3Impact testing, and
3.3.4Nondestructive examination.
3.4The purchaser is referred to the listed supplementary requirements in this specification and to the detailed requirements in
Specification A20/A20M.
3.5If the requirements of this specification are in conflict with the requirements of Specification A20/A20M, the requirements
of this specification shall prevail.
4. Manufacture
4.1 Steelmaking Practice—The steel shall be killed.
1
This specification is under the jurisdiction ofASTM CommitteeA01 on Steel, Stainless Steel and RelatedAlloys and is the direct responsibility of SubcommitteeA01.11
on Steel Plates for Boilers and Pressure Vessels.
Current edition approved March 1, 2006. Published March 2006. Originally approved in 1966. Last previous edition approved in 2001 asA562/A562M–90 (2001). DOI:
10.1520/A0562_A0562M-06.
Current edition approved Oct. 1, 2010. Published November 2010. Originally approved in 1966. Last previous edition approved in 2006 as A562/A562M – 06. DOI:
10.1520/A0562_A0562M-10.
2
For ASME Boiler and Pressure Vessel Code applications, see related Specification SA-562/SA-562M in Section II of that Code.
3
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at service@astm.org. For Annual Book ofASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*ASummary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
A562/A562M – 10
5. Heat Treatment
5.1 Plates shall be thermally treated to produce grain refinement, either by normalizing or heating uniformly for hot forming
at a minimum temperature of 1600°F [870°C] or some higher agreed temperature, and held at this temperature for a minimum of
1 h/in. [2.
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.