ASTM D3994-22
(Specification)Standard Performance Specification for Woven Swimwear Fabrics
Standard Performance Specification for Woven Swimwear Fabrics
SIGNIFICANCE AND USE
5.1 Upon mutual agreement between the purchaser and the supplier, woven fabrics intended for this end use should meet all of the requirements listed in Table 1 of this specification.
5.2 It is recognized that for purposes of fashion or aesthetics the ultimate consumer of articles made from these fabrics may find acceptable fabrics that do not conform to all of the requirements in Table 1. Therefore, one or more of the requirements listed in Table 1 may be modified by mutual agreement between the purchaser and the supplier.
5.2.1 In such cases, any references to the specification shall specify that: “This fabric meets ASTM Specification D3994, except for the following characteristic(s).”
5.3 Where no prepurchase agreement has been reached between the purchaser and the supplier, and in case of controversy, the requirements listed in Table 1 are intended to be used as a guide only. As noted in 5.2, ultimate consumer demands dictate varying performance parameters for any particular style of fabric.
5.4 The significance and use of particular properties and test methods are discussed in the appropriate sections of the specified test methods.
SCOPE
1.1 This performance specification covers woven fabrics for use in men's, women's and children's swimwear, composed of any textile fiber or mixture of textile fibers.
1.2 These requirements apply to the length and width directions for those properties where fabric direction is pertinent.
1.3 The following safety hazards caveat pertains only to the test method described in this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
- Status
- Published
- Publication Date
- 31-Oct-2022
- Technical Committee
- D13 - Textiles
- Drafting Committee
- D13.61 - Apparel
Relations
- Effective Date
- 01-Jan-2024
- Effective Date
- 15-Jul-2017
- Effective Date
- 15-Jul-2017
- Effective Date
- 01-Mar-2017
- Effective Date
- 15-Sep-2015
- Effective Date
- 01-Sep-2015
- Effective Date
- 01-Apr-2015
- Effective Date
- 01-Jul-2013
- Effective Date
- 01-Jul-2013
- Effective Date
- 15-Jun-2013
- Effective Date
- 15-Jun-2013
- Effective Date
- 15-May-2013
- Effective Date
- 01-Jan-2013
- Effective Date
- 01-Feb-2012
- Effective Date
- 01-Feb-2012
Overview
ASTM D3994-22: Standard Performance Specification for Woven Swimwear Fabrics sets critical requirements for woven fabrics designed for use in swimwear for men, women, and children. Developed by ASTM International, this specification ensures fabrics intended for swimwear meet established performance characteristics necessary for quality, durability, and safety. The standard applies to any textile fiber or blend and encompasses both lengthwise and widthwise fabric directions for relevant properties. ASTM D3994-22 reflects industry best practices for fabric performance and addresses both end-use function and consumer safety.
Key Topics
- Scope: Covers woven fabrics for swimwear applications, including any combination of textile fibers. The requirements are relevant in both fabric directions (warp and weft) where applicable.
- Performance Requirements: Specified performance properties include:
- Breaking strength and elongation
- Tear strength
- Resistance to yarn slippage
- Dimensional stability after laundering
- Multiple aspects of colorfastness (to laundering, light, sea water, pool water, perspiration, ozone, various bleaches, and crocking)
- Flammability (must meet or exceed regulatory requirements)
- Test Methods: References a range of ASTM and AATCC test methods for the evaluation of each property, ensuring consistent and reliable assessment.
- Consumer Consideration: Recognizes that for fashion or aesthetic reasons, some performance requirements may be modified by agreement between purchaser and supplier. Any deviation must be clearly stated.
- Safety Notice: Users must establish appropriate safety, health, and environmental practices relevant to the application and local regulations.
Applications
ASTM D3994-22 is essential for several stakeholders in the textile and apparel industry:
- Fabric Manufacturers: Provides a benchmark for producing swimwear fabrics that meet industry performance standards necessary for durability, safety, and consumer satisfaction.
- Apparel Brands and Designers: Assists in sourcing high-quality woven swimwear fabrics, ensuring that their products conform to established international requirements for colorfastness, strength, and dimensional stability.
- Testing Laboratories: Uses the referenced test methods within the standard to confirm compliance for batches of swimwear fabrics, supporting both product development and quality assurance processes.
- Retailers and End-Users: Assures that purchased garments are constructed from fabrics designed to maintain performance characteristics under typical conditions of use, such as exposure to chlorine, sun, sweat, and laundering.
- Regulatory Compliance: Supports compliance with consumer safety regulations and flammability standards for textile products.
Related Standards
Several standards and test methods are referenced within ASTM D3994-22 to evaluate woven swimwear fabrics:
ASTM Standards
- ASTM D123: Terminology Relating to Textiles
- ASTM D5034: Breaking Strength and Elongation (Grab Test)
- ASTM D434, D1424, D2261: Methods for Slippage, Tearing Strength, and related properties
AATCC Methods
- AATCC 8, 15, 16.3, 23, 61, 106, 107, 116, 129, 135, 162, 172, 188: Colorfastness and dimensional changes
Federal Standards
- 16 CFR 1610: Flammability of Clothing Textiles
Military Standards
- MIL-STD-105D: Sampling procedures and inspection
ASTM D3994-22 plays a pivotal role in promoting the consistent quality and safety of woven swimwear fabrics, supporting the needs of manufacturers, brands, laboratories, regulators, and consumers. For textile professionals, adherence to this specification is an effective way to ensure products meet global expectations for performance and compliance.
Buy Documents
ASTM D3994-22 - Standard Performance Specification for Woven Swimwear Fabrics
REDLINE ASTM D3994-22 - Standard Performance Specification for Woven Swimwear Fabrics
Frequently Asked Questions
ASTM D3994-22 is a technical specification published by ASTM International. Its full title is "Standard Performance Specification for Woven Swimwear Fabrics". This standard covers: SIGNIFICANCE AND USE 5.1 Upon mutual agreement between the purchaser and the supplier, woven fabrics intended for this end use should meet all of the requirements listed in Table 1 of this specification. 5.2 It is recognized that for purposes of fashion or aesthetics the ultimate consumer of articles made from these fabrics may find acceptable fabrics that do not conform to all of the requirements in Table 1. Therefore, one or more of the requirements listed in Table 1 may be modified by mutual agreement between the purchaser and the supplier. 5.2.1 In such cases, any references to the specification shall specify that: “This fabric meets ASTM Specification D3994, except for the following characteristic(s).” 5.3 Where no prepurchase agreement has been reached between the purchaser and the supplier, and in case of controversy, the requirements listed in Table 1 are intended to be used as a guide only. As noted in 5.2, ultimate consumer demands dictate varying performance parameters for any particular style of fabric. 5.4 The significance and use of particular properties and test methods are discussed in the appropriate sections of the specified test methods. SCOPE 1.1 This performance specification covers woven fabrics for use in men's, women's and children's swimwear, composed of any textile fiber or mixture of textile fibers. 1.2 These requirements apply to the length and width directions for those properties where fabric direction is pertinent. 1.3 The following safety hazards caveat pertains only to the test method described in this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
SIGNIFICANCE AND USE 5.1 Upon mutual agreement between the purchaser and the supplier, woven fabrics intended for this end use should meet all of the requirements listed in Table 1 of this specification. 5.2 It is recognized that for purposes of fashion or aesthetics the ultimate consumer of articles made from these fabrics may find acceptable fabrics that do not conform to all of the requirements in Table 1. Therefore, one or more of the requirements listed in Table 1 may be modified by mutual agreement between the purchaser and the supplier. 5.2.1 In such cases, any references to the specification shall specify that: “This fabric meets ASTM Specification D3994, except for the following characteristic(s).” 5.3 Where no prepurchase agreement has been reached between the purchaser and the supplier, and in case of controversy, the requirements listed in Table 1 are intended to be used as a guide only. As noted in 5.2, ultimate consumer demands dictate varying performance parameters for any particular style of fabric. 5.4 The significance and use of particular properties and test methods are discussed in the appropriate sections of the specified test methods. SCOPE 1.1 This performance specification covers woven fabrics for use in men's, women's and children's swimwear, composed of any textile fiber or mixture of textile fibers. 1.2 These requirements apply to the length and width directions for those properties where fabric direction is pertinent. 1.3 The following safety hazards caveat pertains only to the test method described in this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM D3994-22 is classified under the following ICS (International Classification for Standards) categories: 61.020 - Clothes. The ICS classification helps identify the subject area and facilitates finding related standards.
ASTM D3994-22 has the following relationships with other standards: It is inter standard links to ASTM D2261-13(2024), ASTM D2261-13(2017), ASTM D2261-13(2017)e1, ASTM D123-17, ASTM D123-15b, ASTM D123-15a, ASTM D123-15, ASTM D1424-09(2013), ASTM D1424-09(2013)e1, ASTM D123-13ae1, ASTM D123-13a, ASTM D123-13, ASTM D2261-13, ASTM D123-12, ASTM D123-12e1. Understanding these relationships helps ensure you are using the most current and applicable version of the standard.
ASTM D3994-22 is available in PDF format for immediate download after purchase. The document can be added to your cart and obtained through the secure checkout process. Digital delivery ensures instant access to the complete standard document.
Standards Content (Sample)
This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation:D3994 −22
Standard Performance Specification for
Woven Swimwear Fabrics
This standard is issued under the fixed designation D3994; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope D2261 Test Method for Tearing Strength of Fabrics by the
Tongue (Single Rip) Procedure (Constant-Rate-of-
1.1 This performance specification covers woven fabrics for
Extension Tensile Testing Machine)
use in men’s, women’s and children’s swimwear, composed of
D2622 Test Method for Sulfur in Petroleum Products by
any textile fiber or mixture of textile fibers.
Wavelength Dispersive X-ray Fluorescence Spectrometry
1.2 These requirements apply to the length and width
D2905 Practice for Statements on Number of Specimens for
directions for those properties where fabric direction is perti- 3
Textiles (Withdrawn 2008)
nent.
D5034 TestMethodforBreakingStrengthandElongationof
1.3 The following safety hazards caveat pertains only to the
Textile Fabrics (Grab Test)
test method described in this specification: This standard does D7022 Terminology Relating to Apparel
not purport to address all of the safety concerns, if any,
2.2 AATCC Test Methods:
associatedwithitsuse.Itistheresponsibilityoftheuserofthis
TM8 Colorfastness to Crocking: Crockmeter Method
standard to establish appropriate safety, health, and environ-
TM15 Colorfastness to Perspirationn
mental practices and determine the applicability of regulatory
TM16.3 Colorfastness to Light
limitations prior to use.
TM23 Colorfastness to Burnt Gas Fumes
1.4 This international standard was developed in accor-
TM61 Colorfastness to Laundering: Accelerated
dance with internationally recognized principles on standard-
TM106 Colorfastness to Water: Sea
ization established in the Decision on Principles for the
TM107 Colorfastness to Water
Development of International Standards, Guides and Recom-
TM116 Colorfastness to Crocking: Rotary Vertical Crock-
mendations issued by the World Trade Organization Technical
meter Method
Barriers to Trade (TBT) Committee.
TM129 Colorfastness to Ozone in the Atmosphere Under
High Humidities
2. Referenced Documents
TM135 Dimensional Changes of FabricsAfter Home Laun-
2.1 ASTM Standards:
dering
D123 Terminology Relating to Textiles
TM162 Colorfastness to Water: Chlorinated Pool
D434 Test Method for Resistance to Slippage of Yarns in
TM172 Colorfastness to Powdered Non-Chlorine Bleach in
Woven Fabrics Using a Standard Seam (Withdrawn
Home Laundering
2003)
TM188 Colorfastness to Chlorine Bleach in Home Launder-
D1424 Test Method for Tearing Strength of Fabrics by
ing
Falling-Pendulum (Elmendorf-Type) Apparatus
EP1 Gray Scale for Color Change
EP2 Gray Scale for Staining
1 EP8 AATCC 9-Step Chromatic Transference Scale
This performance specification is under the jurisdiction of ASTM Committee
D13 on Textiles and is the direct responsibility of Subcommittee D13.61 on 2.3 Federal Standard:
Apparel.
16 CFR 1610 Standard for Flammability of Clothing Tex-
Current edition approved Nov. 1, 2022. Published November 2022. Originally
tiles
approved in 1981. Last previous edition approved in 2014 as D3994 – 14. DOI:
10.1520/D3994-22.
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Available from American Association of Textile Chemists and Colorists
Standards volume information, refer to the standard’s Document Summary page on (AATCC), P.O. Box 12215, Research Triangle Park, NC 27709, http://
the ASTM website. www.aatcc.org.
3 5
The last approved version of this historical standard is referenced on Available from Superintendent of Documents, U.S. Government Printing
www.astm.org. Office, Washington, DC 20402.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
D3994−22
16 CFR, Chapter II—Consumer Product Safety 4. Specification Requirements
Commission, Subchapter D—Flammable Fabrics Act
4.1 The properties of fabrics for woven swimwear shall
Regulations
conform to the specification requirements in Table 1.
2.4 Military Standard:
MIL-STD-105D Sampling Procedures and Tables for In- 5. Significance and Use
spection by Attributes
5.1 Upon mutual agreement between the purchaser and the
supplier, woven fabrics intended for this end use should meet
NOTE 1—Reference to test methods in this standard give only the
permanent part of the designation of ASTM, AATCC, or other test
all of the requirements listed in Table 1 of this specification.
methods. The current editions of each test method cited shall prevail.
5.2 Itisrecognizedthatforpurposesoffashionoraesthetics
the ultimate consumer of articles made from these fabrics may
3. Terminology
find acceptable fabrics that do not conform to all of the
3.1 For all terminology related to Apparel see Terminology
requirements in Table 1. Therefore, one or more of the
D7022.
requirements listed in Table 1 may be modified by mutual
3.1.1 The following terms are relevant to this standard:
agreement between the purchaser and the supplier.
swimwear.
5.2.1 In such cases, any references to the specification shall
3.2 For terms relating to chemical or colorfastness testing,
specify that: “This fabric meets ASTM Specification D3994,
refer to specific AATCC methods. For definitions of all other
except for the following characteristic(s).”
textile terms see Terminology D123.
5.3 Where no prepurchase agreement has been reached
between the purchaser and the supplier, and in case of
controversy, the requirements listed in Table 1 are intended to
be used as a guide only. As noted in 5.2, ultimate consumer
AvailablefromStandardizationDocumentsOrderDesk,Bldg.4SectionD,700
Robbins Ave., Philadelphia, PA 19111-5094, Attn: NPODS.
TABLE 1 Specification Requirements
NOTE 1—Grade in a, b, and c is based on a numerical scale of 5 for negligible or no color change or color transfer to 1 for very severe color change
or color transfer.
Characteristic Requirements Section
A
Breaking strength (load) (CRT): 7.1
Nonstretch fabrics 133 N (30 lbf), min
Stretch fabrics 89 N (20 lbf), min @ 40 % or greater
elongation
Yarn slippage ⁄4-in. (6-mm) separation 89 N (20 lbf), min 7.2
Tear strength (nonstretch direction) 6.7 N (1.5 lbf), min 7.3
Dimensional change:
Laundering 3 %, max 7.4.1
Colorfastness:
Burnt gas fumes—1 cycle 7.5.1
Shade change, original
B
fabric and after 1 laundering Grade 4 ,min
B
Sodium Hypochlorite Bleach Grade 4 ,min 7.5.10
B
Powdered Non-Chlorine Bleach Grade 4 ,min 7.5.11
E
Laundering 7.5.2
B
Shade change Grade 4 ,min
C
Staining Grade 4 ,min
E
Crocking 7.5.3
D
Dry Grade 4 ,min
D
Wet Grade 4 ,min
E
Water 7.5.4
B
Shade change Grade 4 ,min
C
Staining Grade 4 ,min
B
Chlorinated Pool Grade 4 7.5.5
E
Perspiration 7.5.6
B
Shade change Grade 4
C
Staining Grade 4
E
Sea water 7.5.7
B
Shade change Grade 4 ,min
C
Staining Grade 4 ,min
Ozone
B
Shade change Grade 3–4 ,min
B
Light (20 AFUs) (xenon-arc) Grade 4 ,min 7.5.9
Flammability Class 1 or Class 2 7.6
A
See Note 2.
B
AATCC Gray Scale for Color Change.
C
AATCC Gray Scale for Staining.
D
AATCC 9-Step Chromatic Transference Scale.
E
See Note 7.
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: D3994 − 14 D3994 − 22
Standard Performance Specification for
Woven Swimwear Fabrics
This standard is issued under the fixed designation D3994; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This performance specification covers woven fabrics for use in men’s, women’s and children’s swimwear, composed of any
textile fiber or mixture of textile fibers.
1.2 These requirements apply to the length and width directions for those properties where fabric direction is pertinent.
1.3 The following safety hazards caveat pertains only to the test method described in this specification: This standard does not
purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to
establish appropriate safety safety, health, and healthenvironmental practices and determine the applicability of regulatory
limitations prior to use.
1.4 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2.1 ASTM Standards:
D123 Terminology Relating to Textiles
D434 Test Method for Resistance to Slippage of Yarns in Woven Fabrics Using a Standard Seam (Withdrawn 2003)
D1424 Test Method for Tearing Strength of Fabrics by Falling-Pendulum (Elmendorf-Type) Apparatus
D2261 Test Method for Tearing Strength of Fabrics by the Tongue (Single Rip) Procedure (Constant-Rate-of-Extension Tensile
Testing Machine)
D2622 Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-ray Fluorescence Spectrometry
D2905 Practice for Statements on Number of Specimens for Textiles (Withdrawn 2008)
D5034 Test Method for Breaking Strength and Elongation of Textile Fabrics (Grab Test)
D7022 Terminology Relating to Apparel
2.2 AATCC Test Methods:
8TM8 Colorfastness to Crocking: Crockmeter Method
15TM15 Colorfastness to Perspirationn
16.3TM16.3 Colorfastness to Light
23TM23 Colorfastness to Burnt Gas Fumes
61TM61 Colorfastness to Laundering: Accelerated
This performance specification is under the jurisdiction of ASTM Committee D13 on Textiles and is the direct responsibility of Subcommittee D13.61 on Apparel.
Current edition approved March 15, 2014Nov. 1, 2022. Published April 2014November 2022. Originally approved in 1981. Last previous edition approved in 20132014
ε1
as D3994 – 13D3994 – 14. . DOI: 10.1520/D3994-14.10.1520/D3994-22.
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
The last approved version of this historical standard is referenced on www.astm.org.
Available from American Association of Textile Chemists and Colorists (AATCC), P.O. Box 12215, Research Triangle Park, NC 27709, http://www.aatcc.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
D3994 − 22
106TM106 Colorfastness to Water: Sea
107TM107 Colorfastness to Water
116TM116 Colorfastness to Crocking: Rotary Vertical Crockmeter Method
129TM129 Colorfastness to Ozone in the Atmosphere Under High Humidities
135TM135 Dimensional Changes of Fabrics After Home Laundering
162TM162 Colorfastness to Water: Chlorinated Pool
172TM172 Colorfastness to Powdered Non-Chlorine Bleach in Home Laundering
188TM188 Colorfastness to Chlorine Bleach in Home Laundering
Evaluation Procedure No. 1EP1 Gray Scale for Color Change
Evaluation Procedure No. 2EP2 Gray Scale for Staining
Evaluation Procedure No. 8EP8 AATCC 9-Step Chromatic Transference Scale
2.3 Federal Standard:
16 CFR 1610 Standard for Flammability of Clothing Textiles
16 CFR, Chapter II—Consumer Product Safety Commission, Subchapter D—Flammable Fabrics Act Regulations
2.4 Military Standard:
MIL-STD-105D Sampling Procedures and Tables for Inspection by Attributes
NOTE 1—Reference to test methods in this standard give only the permanent part of the designation of ASTM, AATCC, or other test methods. The current
editions of each test method cited shall prevail.
3. Terminology
3.1 For all terminology related to Apparel see Terminology D7022.
3.1.1 The following terms are relevant to this standard: swimwear.
3.2 For terms relating to chemical or colorfastness testing, refer to specific AATCC methods. For definitions of all other textile
terms see Terminology D123.
4. Specification Requirements
4.1 The properties of fabrics for woven swimwear shall conform to the specification requirements in Table 1.
5. Significance and Use
5.1 Upon mutual agreement between the purchaser and the supplier, woven fabrics intended for this end use should meet all of
the requirements listed in Table 1 of this specification.
5.2 It is recognized that for purposes of fashion or aesthetics the ultimate consumer of articles made from these fabrics may find
acceptable fabrics that do not conform to all of the requirements in Table 1. Therefore, one or more of the requirements listed in
Table 1 may be modified by mutual agreement between the purchaser and the supplier.
5.2.1 In such cases, any references to the specification shall specify that: “This fabric meets ASTM Specification D3994, except
for the following characteristic(s).”
5.3 Where no prepurchase agreement has been reached between the purchaser and the supplier, and in case of controversy, the
requirements listed in Table 1 are intended to be used as a guide only. As noted in 5.2, ultimate consumer demands dictate varying
performance parameters for any particular style of fabric.
5.4 The significance and use of particular properties and test methods are discussed in the appropriate sections of the specified test
methods.
Available from Superintendent of Documents, U.S. Government Printing Office, Washington, DC 20402.
Available from Standardization Documents Order Desk, Bldg. 4 Section D, 700 Robbins Ave., Philadelphia, PA 19111-5094, Attn: NPODS.
D3994 − 22
TABLE 1 Specification Requirements
NOTE 1—Grade in a, b, and c is based on a numerical scale of 5 for negligible or no color change or color transfer to 1 for very severe color change
or color transfer.
Characteristic Requirements Section
A
Breaking strength (load) (CRT): 7.1
Nonstretch fabrics 133 N (30 lbf), min
Stretch fabrics 89 N (20 lbf), min @ 40 % or greater
elongation
Yarn slippage ⁄4-in. (6-mm) separation 89 N (20 lbf), min 7.2
Tear strength (nonstretch direction) 6.7 N (1.5 lbf), min 7.3
Dimensional change:
Laundering 3 %, max 7.4.1
Colorfastness:
Burnt gas fumes—1 cycle 7.5.1
Shade change, original
B
fabric and after 1 laundering Grade 4 , min
B
Sodium Hypochlorite Bleach Grade 4 , min 7.5.10
B
Powdered Non-Chlorine Bleach Grade 4 , min 7.5.11
E
Laundering 7.5.2
B
Shade change Grade 4 , min
C
Staining Grade 4 , min
E
Crocking 7.5.3
D
Dry Grade 4 , min
D
Wet Grade 4 , min
E
Water 7.5.4
B
Shade change Grade 4 , min
C
Staining Grade 4 , min
B
Chlorinated Pool Grade 4 7.5.5
E
Perspiration 7.5.6
B
Shade change Grade 4
C
Staining Grade 4
E
Sea water 7.5.7
B
Shade change Grade 4 , min
C
Staining Grade 4 , min
Ozone
B
Shade change Grade 3–4 , min
B
Light (20 AATCC F
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.
Loading comments...