ASTM F1974-09
(Specification)Standard Specification for Metal Insert Fittings for Polyethylene/Aluminum/Polyethylene and Crosslinked Polyethylene/Aluminum/Crosslinked Polyethylene Composite Pressure Pipe
Standard Specification for Metal Insert Fittings for Polyethylene/Aluminum/Polyethylene and Crosslinked Polyethylene/Aluminum/Crosslinked Polyethylene Composite Pressure Pipe
ABSTRACT
This specification covers metal insert fittings with split ring and compression nut (compression joint) and metal insert fittings with copper crimp rings (crimp joint) for four sizes of composite pressure pipe. These fittings are intended for use in cold- and hot-water distribution systems operating at a certain temperature range. These fittings are intended for use in potable water distribution systems for residential and commercial applications, water service, underground irrigation systems, and radient panel heating systems, baseboard, snow- and ice-melt systems, and gases that are compatible with the composite pipe and fittings. The fittings are classified into two classes with split ring and compression nut and fittings with a copper crimp ring, suitable for use with four sizes of PEX/AL/PEX or PE/AL/PE pipe. The fittings shall be made from one of the following metals: wrought copper, cast copper alloy, machined brass, and forged brass. Different tests shall be conducted in order to determine the following properties: hydrostatic burst, hydrostatic sustained pressure strength, thermocycling, and excessive temperature and pressure capability. The sealing surfaces of the insert shall be smooth and free of foreign material. The fitting walls shall be free of cracks, holes, blisters, voids, foreign inclusions or other defects that are visible to the naked eye and that affect the wall integrity.
SCOPE
1.1 This specification covers metal insert fittings with split ring and compression nut (compression joint) and metal insert fittings with copper crimp rings (crimp joint) for four sizes of composite pressure pipe. These fittings are intended for use in 125 psi (690 kPa) cold- and hot-water distribution systems operating at temperatures up to and including 180 °F (82 °C). (When used in polyethylene/aluminum/polyethylene systems the maximum operating temperature is limited by the pipe to 140 °F (60 °C) and where applicable 180°F (82°C)). Included are the requirements for materials, workmanship, burst pressure, sustained pressure, excessive temperature and pressure, temperature cycling tests, and markings to be used on the fittings and rings. The fittings covered by this specification are intended for use in potable water distribution systems for residential and commercial applications, water service, underground irrigation systems, and radient panel heating systems, baseboard, snow- and ice-melt systems, and gases that are compatible with the composite pipe and fittings.
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
Note 1—The tables show the “nominal size” in millimetres with the inch size in parentheses. This exception is made to harmonize the “nominal size” with the two pipe standards, F1281 and F1282.
1.3 The following precautionary caveat pertains only to the test method portion, Section 9, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:F1974 −09
StandardSpecification for
Metal Insert Fittings for Polyethylene/Aluminum/
Polyethylene and Crosslinked Polyethylene/Aluminum/
1
Crosslinked Polyethylene Composite Pressure Pipe
This standard is issued under the fixed designation F1974; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* 2. Referenced Documents
2
2.1 ASTM Standards:
1.1 This specification covers metal insert fittings with split
B16/B16M Specification for Free-Cutting Brass Rod, Bar
ring and compression nut (compression joint) and metal insert
and Shapes for Use in Screw Machines
fittings with copper crimp rings (crimp joint) for four sizes of
B36/B36M Specification for Brass Plate, Sheet, Strip, And
composite pressure pipe. These fittings are intended for use in
Rolled Bar
125 psi (690 kPa) cold- and hot-water distribution systems
B62 Specification for Composition Bronze or Ounce Metal
operating at temperatures up to and including 180 °F (82 °C).
Castings
(When used in polyethylene/aluminum/polyethylene systems
B75 Specification for Seamless Copper Tube
the maximum operating temperature is limited by the pipe to
B134/B134M Specification for Brass Wire
140 °F (60 °C) and where applicable 180°F (82°C)). Included
B140/B140M Specification for Copper-Zinc-Lead (Red
are the requirements for materials, workmanship, burst
Brass or Hardware Bronze) Rod, Bar, and Shapes
pressure, sustained pressure, excessive temperature and
B159/B159M Specification for Phosphor Bronze Wire
pressure, temperature cycling tests, and markings to be used on
B283 Specification for Copper and Copper-Alloy Die Forg-
the fittings and rings. The fittings covered by this specification
ings (Hot-Pressed)
are intended for use in potable water distribution systems for
B371/B371M Specification for Copper-Zinc-Silicon Alloy
residential and commercial applications, water service, under-
Rod
ground irrigation systems, and radient panel heating systems,
B584 Specification for Copper Alloy Sand Castings for
baseboard, snow- and ice-melt systems, and gases that are
General Applications
compatible with the composite pipe and fittings.
D618 Practice for Conditioning Plastics for Testing
1.2 The values stated in inch-pound units are to be regarded D1598 Test Method for Time-to-Failure of Plastic Pipe
as standard. The values given in parentheses are mathematical
Under Constant Internal Pressure
conversions to SI units that are provided for information only D1599 Test Method for Resistance to Short-Time Hydraulic
and are not considered standard. Pressure of Plastic Pipe, Tubing, and Fittings
D1600 Terminology forAbbreviatedTerms Relating to Plas-
NOTE 1—The tables show the “nominal size” in millimetres with the
tics
inch size in parentheses. This exception is made to harmonize the
D2122 Test Method for Determining Dimensions of Ther-
“nominal size” with the two pipe standards, F1281 and F1282.
moplastic Pipe and Fittings
1.3 The following precautionary caveat pertains only to the
D2240 Test Method for Rubber Property—Durometer Hard-
test method portion, Section 9, of this specification. This
ness
standarddoesnotpurporttoaddressallofthesafetyconcerns,
E18 Test Methods for Rockwell Hardness of Metallic Ma-
ifany,associatedwithitsuse.Itistheresponsibilityoftheuser
terials
of this standard to establish appropriate safety and health
F412 Terminology Relating to Plastic Piping Systems
practices and determine the applicability of regulatory limita-
F1281 Specification for Crosslinked Polyethylene/
tions prior to use.
Aluminum/Crosslinked Polyethylene (PEX-AL-PEX)
Pressure Pipe
1
This specification is under the jurisdiction ofASTM Committee F17 on Plastic
2
Piping Systems and is the direct responsibility of Subcommittee F17.10 on Fittings. For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Current edition approved Dec. 1, 2009. Published January 2010. Originally contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
approved in 1999. Last previous edition approved in 2008 as F1974 - 08. DOI: Standards volume information, refer to the standard’s Document Summary page on
10.1520/F1974-09. the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
F1974−09
F1282 Specification for Polyethylene/Aluminum/ 5.1.5 Forged Brass Fittings—Forged brass fittings shall be
Polyethylene (PE-AL-PE) Composite Pressure Pipe made from material meeting the requirements o
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
An American National Standard
Designation:F1974–08 Designation: F1974 – 09
Standard Specification for
Metal Insert Fittings for Polyethylene/Aluminum/
Polyethylene and Crosslinked Polyethylene/Aluminum/
1
Crosslinked Polyethylene Composite Pressure Pipe
This standard is issued under the fixed designation F1974; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope*
1.1 Thisspecificationcoversmetalinsertfittingswithsplitringandcompressionnut(compressionjoint)andmetalinsertfittings
with copper crimp rings (crimp joint) for four sizes of composite pressure pipe. These fittings are intended for use in 125 psi (690
kPa) cold- and hot-water distribution systems operating at temperatures up to and including 180 °F (82 °C). (When used in
polyethylene/aluminum/polyethylene systems the maximum operating temperature is limited by the pipe to 140 °F (60 °C) and
where applicable 180°F (82°C)). Included are the requirements for materials, workmanship, burst pressure, sustained pressure,
excessive temperature and pressure, temperature cycling tests, and markings to be used on the fittings and rings. The fittings
covered by this specification are intended for use in potable water distribution systems for residential and commercial applications,
water service, underground irrigation systems, and radient panel heating systems, baseboard, snow- and ice-melt systems, and
gases that are compatible with the composite pipe and fittings.
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
NOTE 1—The tables show the “nominal size” in millimetres with the inch size in parentheses. This exception is made to harmonize the “nominal size”
with the two pipe standards, F1281 and F1282.
1.3 The following precautionary caveat pertains only to the test method portion, Section 9, of this specification. This standard
does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this
standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
2. Referenced Documents
2
2.1 ASTM Standards:
B16/B16M Specification for Free-Cutting Brass Rod, Bar and Shapes for Use in Screw Machines
B36/B36M Specification for Brass Plate, Sheet, Strip, And Rolled Bar
B62 Specification for Composition Bronze or Ounce Metal Castings
B75 Specification for Seamless Copper Tube
B134/B134M Specification for Brass Wire
B140/B140M Specification for Copper-Zinc-Lead (Red Brass or Hardware Bronze) Rod, Bar, and Shapes
B159/B159M Specification for Phosphor Bronze Wire
B283 Specification for Copper and Copper-Alloy Die Forgings (Hot-Pressed)
B371/B371M Specification for Copper-Zinc-Silicon Alloy Rod
B584 Specification for Copper Alloy Sand Castings for General Applications
D618 Practice for Conditioning Plastics for Testing
D1598 Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure
D1599 Test Method for Resistance to Short-Time Hydraulic Pressure of Plastic Pipe, Tubing, and Fittings
D1600 Terminology for Abbreviated Terms Relating to Plastics
D2122 Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
D2240 Test Method for Rubber PropertyDurometer Hardness
E18 Test Methods for Rockwell Hardness of Metallic Materials
1
This specification is under the jurisdiction of ASTM Committee F17 on Plastic Piping Systems and is the direct responsibility of Subcommittee F17.10 on Fittings.
Current edition approved Nov.Dec. 1, 2008.2009. Published November 2008.January 2010. Originally approved in 1999. Last previous edition approved in 20042008 as
F1974 - 048. DOI: 10.1520/F1974-089.
2
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
F1974 – 09
F41
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.