ASTM B829-04a
(Specification)Standard Specification for General Requirements for Nickel and Nickel Alloys Seamless Pipe and Tube
Standard Specification for General Requirements for Nickel and Nickel Alloys Seamless Pipe and Tube
ABSTRACT
This general specification contains the mandatory requirements to the ASTM standards listed herein for seamless pipes and tubes made from nickel and nickel alloys. In case of conflict, the requirements listed in the particular product specification takes precedence over those listed here.
SCOPE
1.1 This specification contains various requirements that, with the exception of Sections 5 and 10, are mandatory requirements to the following ASTM nickel and nickel alloy, seamless pipe and tube specifications:
1.2 One or more of the test requirements of Section apply only if specifically stated in the product specification or in the purchase order.
1.3 In case of conflict between a requirement of the product specification and a requirement of this general specification, only the requirement of the product specification needs to be satisfied.
1.4 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.
1.5 The following safety hazards caveat pertains only to the test requirements portion, Section 5, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: B 829 – 04a
Standard Specification for
General Requirements for Nickel and Nickel Alloys
1
Seamless Pipe and Tube
This standard is issued under the fixed designation B 829; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
1. Scope* 1.4 The values stated in inch-pound units are to be regarded
as the standard. The values given in parentheses are for
1.1 This specification contains various requirements that,
information only.
with the exception of Sections 5 and 10, are mandatory
1.5 The following safety hazards caveat pertains only to the
requirements to the following ASTM nickel and nickel alloy,
test requirements portion, Section 5, of this specification: This
seamless pipe and tube specifications:
standard does not purport to address all of the safety concerns,
ASTM
Title of Specification
2
if any, associated with its use. It is the responsibility of the user
Designation
Nickel Seamless Pipe and Tube B 161
of this standard to establish appropriate safety and health
Seamless Nickel and Nickel Alloy, Condenser and Heat Ex- B 163
practices and determine the applicability of regulatory limita-
changer Tubes
tions prior to use.
Nickel-Copper Alloy (UNS N04400) Seamless Pipe and Tube B 165
Nickel-Chromium-Iron Alloys (UNS N06600, N06601, and B 167
N06690) Seamless Pipe and Tube
2. Referenced Documents
Nickel-Iron-Chromium Alloy Seamless Pipe and Tube B 407
2
2.1 ASTM Standards:
Nickel-Iron-Chromium-Molybdenum-Copper Alloy (UNS N08825 B 423
and N08221) Seamless Pipe and Tube
B 880 SpecificationforGeneralRequirementsforChemical
Nickel-Chromium-Molybdenum-Columbium Alloys (UNS B 444
Check Analysis Limits for Nickel, Nickel Alloys and
N06625) Pipe and Tube
Nickel-Chromium-Iron-Columbium-Molybdenum-Tungsten Alloy B 445 Cobalt Alloys
(UNS N06102) Seamless Pipe and Tube
E 8 Test Methods for Tension Testing of Metallic Materials
Nickel-Iron-Chromium-Silicon Alloys (UNS N08330 and UNS B 535
E 18 Test Methods for Rockwell Hardness and Rockwell
N08332) Seamless Pipe
Copper-Beryllium Alloy Forgings and Extrusion B 570 Superficial Hardness of Metallic Materials
Seamless Nickel and Nickel-Cobalt Alloy Pipe and Tube B 622
E 29 Practice for Using Significant Digits in Test Data to
UNS N08028 Seamless Tubes B 668
Determine Conformance with Specifications
UNS N08904, UNS N08925 and UNS N08926 Seamless Pipe B 677
3
and Tube E 39 Methods for Chemical Analysis of Nickel
Iron-Nickel-Chromium-Molybdenum Alloys (UNS N08366 and B 690
E 76 Test Methods for ChemicalAnalysis of Nickel-Copper
UNS N08367) Seamless Pipe and Tube
3
Alloys
Ni-Cr-Mo-Co-W-Fe-Si Alloy (UNS N06333) Seamless Pipe and B 722
Tube E 112 Test Methods for Determining the Average Grain
Seamless UNS N08020, UNS N08026, and UNS N08024 B 729
Size
Nickel-Alloy Pipe and Tube
E 213 Practice for Ultrasonic Examination of Metal Pipe
and Tubing
1.2 One or more of the test requirements of Section 5 apply
E 426 Practice for Electromagnetic (Eddy-Current) Exami-
only if specifically stated in the product specification or in the
nation of Seamless and Welded Tubular Products, Austen-
purchase order.
itic Stainless Steel and Similar Alloys
1.3 In case of conflict between a requirement of the product
E 571 Practice for Electromagnetic (Eddy-Current) Exami-
specification and a requirement of this general specification,
nation of Nickel and Nickel Alloy Tubular Products
only the requirement of the product specification needs to be
E 1473 Test Methods for Chemical Analysis of Nickel,
satisfied.
Cobalt, and High-Temperature Alloys
4
2.2 ANSI Standards:
B 1.20.1 Pipe Threads
1
This specification is under the jurisdiction of ASTM Committee B02 on
B 36.10 Welded and Seamless Wrought Steel Pipe
Nonferrous Metals and Alloys and is the direct responsibility of Subcommittee
B02.07 on Refined Nickel and Cobalt and Their Alloys.
B 36.19 Stainless Steel Pipe
Current edition approved Oct. 1, 2004. Published October 2004. Originally
approved in 1992. Last previous edition approved in 2004 as B 829 – 04.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
3
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Withdrawn.
4
Standards volume information, refer to the standard’s Document Summary page on Available fromAmerican National Standards Institute (ANSI), 25 W. 43rd St.,
the ASTM website. 4th Floor, New York, NY 10036.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 -------------------
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:B 829–04 Designation: B 829 – 04a
Standard Specification for
General Requirements for Nickel and Nickel Alloys
1
Seamless Pipe and Tube
This standard is issued under the fixed designation B 829; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope*
1.1 This specification contains various requirements that, with the exception of Sections 5 and 10, are mandatory requirements
to the following ASTM nickel and nickel alloy, seamless pipe and tube specifications:
ASTM
Title of Specification
2
Designation
Nickel Seamless Pipe and Tube B 161
Seamless Nickel and Nickel Alloy, Condenser and Heat Ex- B 163
changer Tubes
Nickel-Copper Alloy (UNS N04400) Seamless Pipe and Tube B 165
Nickel-Chromium-Iron Alloys (UNS N06600, N06601, and B 167
N06690) Seamless Pipe and Tube
Nickel-Iron-Chromium Alloy Seamless Pipe and Tube B 407
Nickel-Iron-Chromium-Molybdenum-Copper Alloy (UNS N08825 B 423
and N08221) Seamless Pipe and Tube
Nickel-Chromium-Molybdenum-Columbium Alloys (UNS B 444
N06625) Pipe and Tube
Nickel-Chromium-Iron-Columbium-Molybdenum-Tungsten Alloy B 445
(UNS N06102) Seamless Pipe and Tube
Nickel-Iron-Chromium-Silicon Alloys (UNS N08330 and UNS B 535
N08332) Seamless Pipe
Copper-Beryllium Alloy Forgings and Extrusion B 570
Seamless Nickel and Nickel-Cobalt Alloy Pipe and Tube B 622
UNS N08028 Seamless Tubes B 668
UNS N08904, UNS N08925 and UNS N08926 Seamless Pipe B 677
and Tube
Iron-Nickel-Chromium-Molybdenum Alloys (UNS N08366 and B 690
UNS N08367) Seamless Pipe and Tube
Ni-Cr-Mo-Co-W-Fe-Si Alloy (UNS N06333) Seamless Pipe and B 722
Tube
Seamless UNS N08020, UNS N08026, and UNS N08024 B 729
Nickel-Alloy Pipe and Tube
1.2 One or more of the test requirements of Section 5 apply only if specifically stated in the product specification or in the
purchase order.
1.3 In case of conflict between a requirement of the product specification and a requirement of this general specification, only
the requirement of the product specification needs to be satisfied.
1.4 The values stated in inch-pound units are to be regarded as the standard.The values given in parentheses are for information
only.
1.5 The following safety hazards caveat pertains only to the test requirements portion, Section 5, of this specification: This
standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user
of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior
to use.
2. Referenced Documents
2
2.1 ASTM Standards:
1
ThisspecificationisunderthejurisdictionofASTMCommitteeB02onNonferrousMetalsandAlloysandisthedirectresponsibilityofSubcommitteeB02.07onRefined
Nickel and Cobalt and Their Alloys.
Current edition approved Feb.Oct. 1, 2004. Published FebruaryOctober 2004. Originally approved in 1992. Last previous edition approved in 19992004asB
829–99.B 829 – 04.
2
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
B 829 – 04a
B 880 SpecificationforGeneralRequirementsforChemicalCheckAnalysisLimitsforNickel,NickelAlloysandCobaltAlloys
E8 Test Methods for Tension Testing of Metallic Materials
E18 Test Methods for Rockwell Hardness and Rockwell Superficial Hardness of Metallic Materials
E29 Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
E39
3
E39 Methods for Chemical Analysis of Nickel
E76
3
E76 Test Methods for Chemical Analysis of Nickel-Copper Alloys
E112 Test Methods for Determining the Average Grain Size
E 213 Practice for Ultrasonic Examination of Metal Pipe and Tubing
E 426 PracticeforElectromagnetic(Eddy-Current)ExaminationofSeamlessandWeldedTubularProducts,AusteniticStainless
Steel and Similar Alloys
E 571 Practice for Electromagnetic (Eddy-Current) Examination of Nickel and Nickel Alloy Tubular Products
E1473
E 1473 Test Methods for Chemical Analysi
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.