ASTM F467-13e2

Standard Specification for Nonferrous Nuts for General Use

ABSTRACT
This specification covers the requirements for commercial wrought nonferrous nuts in nominal thread diameters M6 to M36 inclusive in a number of alloys in common use and intended for general service applications. Materials shall be tested and shall conform to the chemical composition, hardness, proof stress, proof load, and tensile stress requirements.
SIGNIFICANCE AND USE
11.1 For purposes of determining compliance with the specified limits for requirements of the properties listed in this specification, an observed value or calculated value shall be rounded in accordance with Practice E29.
SCOPE
1.1 This specification covers the requirements for commercial wrought nonferrous nuts 0.250 to 1.500 in. inclusive in diameter in a number of alloys in common use and intended for general service applications.  
1.2 Applicable bolts, cap screws, and studs for use with nuts covered by this specification are covered by Specification F468.  
1.3 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard.Note 1—This specification is the inch-pound companion to Specification F467M; therefore, no SI equivalents are presented in the specification.

General Information

• Status: Historical
• Publication Date: 31-Mar-2013
• ICS: 21.060.20 - Nuts
• Technical Committee: F16 - Fasteners
• Drafting Committee: F16.04 - Nonferrous Fasteners

Relations

• Replaces: ASTM F467-13e1 - Standard Specification for Nonferrous Nuts for General Use
• Effective Date: 01-Apr-2013
• Replaced By: ASTM F467-13(2018) - Standard Specification for Nonferrous Nuts for General Use
• Effective Date: 01-Sep-2018
• Referred By: ASTM F1155-10(2019) - Standard Practice for Selection and Application of Piping System Materials
• Effective Date: 01-Apr-2013
• Referred By: ASTM C1802-23 - Standard Specification for Design, Testing, Manufacture, Selection, and Installation of Horizontal Fabricated Metal Access Hatches for Utility, Water, and Wastewater Structures
• Effective Date: 01-Apr-2013
• Referred By: ASTM B746/B746M-22 - Standard Specification for Corrugated Aluminum Alloy Structural Plate for Field-Bolted Pipe, Pipe-Arches, and Arches
• Effective Date: 01-Apr-2013
• Referred By: ASTM F1718-01(2019) - Standard Specification for Rotary Positive Displacement Distillate Fuel Pumps
• Effective Date: 01-Apr-2013
• Referred By: ASTM F1508-96(2021) - Standard Specification for Angle Style, Pressure Relief Valves for Steam, Gas, and Liquid Services
• Effective Date: 01-Apr-2013
• Referred By: ASTM B745/B745M-15(2021) - Standard Specification for Corrugated Aluminum Pipe for Sewers and Drains
• Effective Date: 01-Apr-2013
• Referred By: ASTM F468-23 - Standard Specification for Nonferrous Bolts, Hex Cap Screws, Socket Head Cap Screws, and Studs for General Use
• Effective Date: 01-Apr-2013
• Referred By: ASTM F1370-92(2019)e1 - Standard Specification for Pressure-Reducing Valves for Water Systems, Shipboard
• Effective Date: 01-Apr-2013

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
´2
Designation:F467 −13
Standard Specification for
1
Nonferrous Nuts for General Use
ThisstandardisissuedunderthefixeddesignationF467;thenumberimmediatelyfollowingthedesignationindicatestheyearoforiginal
adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.Asuperscript
epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1
ε NOTE—Table 2 was editorially corrected in February 2014.
2
ε NOTE—17.1 was editorially corrected in May 2014.
1. Scope* E34 Test Methods for Chemical Analysis of Aluminum and
Aluminum-Base Alloys
1.1 This specification covers the requirements for commer-
E38 Methods for Chemical Analysis of Nickel-Chromium
cial wrought nonferrous nuts 0.250 to 1.500 in. inclusive in
3
and Nickel-Chromium-Iron Alloys (Withdrawn 1989)
diameterinanumberofalloysincommonuseandintendedfor
E53 Test Method for Determination of Copper in Unalloyed
general service applications.
Copper by Gravimetry
1.2 Applicablebolts,capscrews,andstudsforusewithnuts
E54 Test Methods for ChemicalAnalysis of Special Brasses
covered by this specification are covered by Specification 3
and Bronzes (Withdrawn 2002)
F468.
E55 Practice for Sampling Wrought Nonferrous Metals and
1.3 The values stated in inch-pound units are to be regarded Alloys for Determination of Chemical Composition
as standard. No other units of measurement are included in this
E62 Test Methods for Chemical Analysis of Copper and
3
standard.
CopperAlloys (Photometric Methods)(Withdrawn 2010)
E75 Test Methods for Chemical Analysis of Copper-Nickel
NOTE 1—This specification is the inch-pound companion to Specifica-
3
and Copper-Nickel-Zinc Alloys (Withdrawn 2010)
tionF467M;therefore,noSIequivalentsarepresentedinthespecification.
E76 Test Methods for Chemical Analysis of Nickel-Copper
3
2. Referenced Documents
Alloys (Withdrawn 2003)
2 E92 Test Methods for Vickers Hardness and Knoop Hard-
2.1 ASTM Standards:
ness of Metallic Materials
B154 Test Method for Mercurous Nitrate Test for Copper
E101 TestMethodforSpectrographicAnalysisofAluminum
Alloys
and Aluminum Alloys by the Point-to-Plane Technique
B574 Specification for Low-Carbon Nickel-Chromium-
3
(Withdrawn 1996)
Molybdenum, Low-Carbon Nickel-Molybdenum-
E120 Test Methods for Chemical Analysis of Titanium and
Chromium, Low-Carbon Nickel-Molybdenum-
3
Titanium Alloys (Withdrawn 2003)
Chromium-Tantalum, Low-Carbon Nickel-Chromium-
E165 Practice for Liquid Penetrant Examination for General
Molybdenum-Copper, and Low-Carbon Nickel-
Industry
Chromium-Molybdenum-Tungsten Alloy Rod
E227 Test Method for Optical Emission Spectrometric
D3951 Practice for Commercial Packaging
Analysis of Aluminum and Aluminum Alloys by the
E18 Test Methods for Rockwell Hardness of Metallic Ma-
3
Point-to-Plane Technique (Withdrawn 2002)
terials
E354 Test Methods for Chemical Analysis of High-
E29 Practice for Using Significant Digits in Test Data to
Temperature,Electrical,Magnetic,andOtherSimilarIron,
Determine Conformance with Specifications
Nickel, and Cobalt Alloys
E478 Test Methods for ChemicalAnalysis of CopperAlloys
1
E1409 Test Method for Determination of Oxygen and Nitro-
This specification is under the jurisdiction of ASTM Committee F16 on
Fasteners and is the direct responsibility of Subcommittee F16.04 on Nonferrous
gen in Titanium and TitaniumAlloys by Inert Gas Fusion
Fasteners.
F468 Specification for Nonferrous Bolts, Hex Cap Screws,
Current edition approved April 1, 2013. Published May 2013. Originally
ε1 Socket Head Cap Screws, and Studs for General Use
approved in 1976. Last previous edition approved in 2006 as F467 – 08 . DOI:
10.1520/F0467-13E01.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM
3
Standards volume information, refer to the standard’s Document Summary page on The last approved version of this historical standard is referenced on
the ASTM website. www.astm.org.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
´2
F467−13
F606 Test Methods for Determining the Mechanical Proper-
Alloy Condition
ties of Externally and Internally Threaded Fasteners,
Copper (all alloys) As formed or stress relieved at manufacturer’s
Washers, and Rivets (Metric) F0606_F0606M
option
Nickel alloys 400 and 405 As formed or stress relieved at manufacturer’s
F1470 Practice for Fastener Sampling for Specified Me-
option
chanical Properties and Performance Inspection
Nickel alloy 500 Solution annealed and aged
4
Aluminum all
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
´2 ´2
Designation: F467 − 13 F467 − 13
Standard Specification for
1
Nonferrous Nuts for General Use
This standard is issued under the fixed designation F467; the number immediately following the designation indicates the year of original
adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A superscript
epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1
ε NOTE—Table 2Table 2 was editorially corrected in February 2014.
2
ε NOTE—17.1 was editorially corrected in May 2014.
1. Scope*
1.1 This specification covers the requirements for commercial wrought nonferrous nuts 0.250 to 1.500 in. inclusive in diameter
in a number of alloys in common use and intended for general service applications.
1.2 Applicable bolts, cap screws, and studs for use with nuts covered by this specification are covered by Specification F468.
1.3 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this
standard.
NOTE 1—This specification is the inch-pound companion to Specification F467M; therefore, no SI equivalents are presented in the specification.
2. Referenced Documents
2
2.1 ASTM Standards:
B154 Test Method for Mercurous Nitrate Test for Copper Alloys
B574 Specification for Low-Carbon Nickel-Chromium-Molybdenum, Low-Carbon Nickel-Molybdenum-Chromium, Low-
Carbon Nickel-Molybdenum-Chromium-Tantalum, Low-Carbon Nickel-Chromium-Molybdenum-Copper, and Low-Carbon
Nickel-Chromium-Molybdenum-Tungsten Alloy Rod
D3951 Practice for Commercial Packaging
E18 Test Methods for Rockwell Hardness of Metallic Materials
E29 Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
3
E34 Test Methods for Chemical Analysis of Aluminum and Aluminum-Base Alloys (Withdrawn 2017)
3
E38 Methods for Chemical Analysis of Nickel-Chromium and Nickel-Chromium-Iron Alloys (Withdrawn 1989)
E53 Test Method for Determination of Copper in Unalloyed Copper by Gravimetry
3
E54 Test Methods for Chemical Analysis of Special Brasses and Bronzes (Withdrawn 2002)
E55 Practice for Sampling Wrought Nonferrous Metals and Alloys for Determination of Chemical Composition
3
E62 Test Methods for Chemical Analysis of Copper and Copper Alloys (Photometric Methods) (Withdrawn 2010)
3
E75 Test Methods for Chemical Analysis of Copper-Nickel and Copper-Nickel-Zinc Alloys (Withdrawn 2010)
3
E76 Test Methods for Chemical Analysis of Nickel-Copper Alloys (Withdrawn 2003)
E92 Test Methods for Vickers Hardness and Knoop Hardness of Metallic Materials
E101 Test Method for Spectrographic Analysis of Aluminum and Aluminum Alloys by the Point-to-Plane Technique (Withdrawn
3
1996)
3
E120 Test Methods for Chemical Analysis of Titanium and Titanium Alloys (Withdrawn 2003)
E165 Practice for Liquid Penetrant Examination for General Industry
E227 Test Method for Optical Emission Spectrometric Analysis of Aluminum and Aluminum Alloys by the Point-to-Plane
3
Technique (Withdrawn 2002)
E354 Test Methods for Chemical Analysis of High-Temperature, Electrical, Magnetic, and Other Similar Iron, Nickel, and
Cobalt Alloys
1
This specification is under the jurisdiction of ASTM Committee F16 on Fasteners and is the direct responsibility of Subcommittee F16.04 on Nonferrous Fasteners.
ε1
Current edition approved April 1, 2013. Published May 2013. Originally approved in 1976. Last previous edition approved in 2006 as F467 – 08 . DOI:
10.1520/F0467-13E01.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM
Standardsvolume information, refer to the standard’s Document Summary page on the ASTM website.
3
The last approved version of this historical standard is referenced on www.astm.org.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
´2
F467 − 13
E478 Test Methods for Chemical Analysis of Copper Alloys
E1409 Test Method for Determination of Oxygen and Nitrogen in Titanium and Titanium Alloys by Inert Gas Fusion
F468 Specification for Nonferrous Bolts, Hex Cap Screws, Socket Head Cap Screws, and Studs for General Use
F606 Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fastene
...