ASTM D3311-09

Standard Specification for Drain, Waste, and Vent (DWV) Plastic Fittings Patterns

ABSTRACT
This specification illustrates the standard fitting geometries and laying lengths of plastic fittings intended for use with outside diameter controlled pipes in drain, waste, and vent (DWV) applications.
SCOPE
1.1 This specification provides standard fitting geometries and laying lengths for plastic fittings intended for use in drain, waste, and vent applications. (See Specifications D 2661 and D 2665.)
1.2 Fittings meeting the requirements of this standard specification are designed for use with outside diameter controlled pipe. The inside diameter can vary significantly as the wall thickness and outside diameter varies and therefore is not suitable for use as a fitting socket.  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

General Information

• Status: Historical
• Publication Date: 30-Apr-2009
• ICS: 23.040.45 - Plastics fittings
• Technical Committee: F17 - Plastic Piping Systems
• Drafting Committee: F17.63 - DWV

Relations

• Replaces: ASTM D3311-08 - Standard Specification for Drain, Waste, and Vent (DWV) Plastic Fittings Patterns
• Effective Date: 01-May-2009
• Replaced By: ASTM D3311-09a - Standard Specification for Drain, Waste, and Vent (DWV) Plastic Fittings Patterns
• Effective Date: 01-Aug-2009
• Referred By: ASTM F1901-22 - Standard Specification for Polyethylene (PE) Pipe and Fittings for Roof Drain Systems
• Effective Date: 01-May-2009
• Referred By: ASTM F1499-22 - Standard Specification for Coextruded Composite Drain, Waste, and Vent Pipe (DWV)
• Effective Date: 01-May-2009
• Referred By: ASTM F3128-23 - Standard Specification for Poly(Vinyl Chloride) (PVC) Schedule 40 Drain, Waste, and Vent Pipe with a Cellular Core
• Effective Date: 01-May-2009
• Referred By: ASTM D2661-21 - Standard Specification for Acrylonitrile-Butadiene-Styrene (ABS) Schedule 40 Plastic Drain, Waste, and Vent Pipe and Fittings
• Effective Date: 01-May-2009
• Referred By: ASTM F2618-21 - Standard Specification for Chlorinated Poly (Vinyl Chloride) (CPVC) Pipe and Fittings for Chemical Waste Drainage Systems
• Effective Date: 01-May-2009
• Referred By: ASTM F1673-10(2021)e1 - Standard Specification for Polyvinylidene Fluoride (PVDF) Corrosive Waste Drainage Systems
• Effective Date: 01-May-2009
• Referred By: ASTM D2949-22 - Standard Specification for 3.25-in. Outside Diameter Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings
• Effective Date: 01-May-2009
• Referred By: ASTM F3371-22 - Standard Specification for Polyolefin Pipe and Fittings for Drainage, Waste, and Vent Applications
• Effective Date: 01-May-2009
• Referred By: ASTM F2390-21 - Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent (DWV) Pipe and Fittings Having Post-Industrial Recycle Content
• Effective Date: 01-May-2009
• Referred By: ASTM F628-23 - Standard Specification for Acrylonitrile-Butadiene-Styrene (ABS) Schedule 40 Plastic Drain, Waste, and Vent Pipe With a Cellular Core
• Effective Date: 01-May-2009
• Referred By: ASTM D2665-20 - Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings
• Effective Date: 01-May-2009
• Referred By: ASTM F891-16 - Standard Specification for Coextruded Poly(Vinyl Chloride) (PVC) Plastic Pipe With a Cellular Core
• Effective Date: 01-May-2009
• Referred By: ASTM F1412-22 - Standard Specification for Polyolefin Pipe and Fittings for Corrosive Waste Drainage Systems
• Effective Date: 01-May-2009

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
An American National Standard
Designation: D 3311 – 09
Standard Specification for
1
Drain, Waste, and Vent (DWV) Plastic Fittings Patterns
This standard is issued under the fixed designation D 3311; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope (ABS) Schedule 40 Plastic Drain, Waste, and Vent Pipe
and Fittings
1.1 This specification provides standard fitting geometries
D 2665 Specification for Poly(Vinyl Chloride) (PVC) Plas-
and laying lengths for plastic fittings intended for use in drain,
tic Drain, Waste, and Vent Pipe and Fittings
waste, and vent applications. (See Specifications D 2661 and
D 2665.)
3. Requirements
1.2 Fittings meeting the requirements of this standard speci-
3.1 Fittings shall conform to the geometries and laying
fication are designed for use with outside diameter controlled
lengths as shown inTables 1-46 and Fig. 1.Tolerances shall be
pipe. The inside diameter can vary significantly as the wall
1
6 ⁄16 in. unless otherwise specified.
thickness and outside diameter varies and therefore is not
3.2 Spigot and hub dimensions shall conform to the require-
suitable for use as a fitting socket.
ments of the referencing standard.
1.3 The values stated in inch-pound units are to be regarded
3.3 The exact outside shape of a fitting is not determined by
as standard. The values given in parentheses are mathematical
the outline drawings shown in this specification but rather by
conversions to SI units that are provided for information only
the socket dimensions, wall thickness requirements, waterway,
and are not considered standard.
laying lengths, and any other critical dimensions that may be
2. Referenced Documents specified.
2
3.4 The pitch of sockets for patterns with 90° angles (except
2.1 ASTM Standards:
1
vent fittings) shall be ⁄4 in./ft or 1° 12 min.
D 2661 Specification for Acrylonitrile-Butadiene-Styrene
3.5 On double reducing sanitary tees, the G2 dimension on
branches will be calculated on the larger size and centerlines
shall remain the same for both branches.
1
This specification is under the jurisdiction ofASTM Committee F17 on Plastic
3.6 All other dimensions, materials and property require-
Piping Systems and is the direct responsibility of Subcommittee F17.63 on DWV.
Current edition approved May 1, 2009. Published June 2009. Originally ments shall be in conformance with the referencing standard.
approved in 1974. Last previous edition approved in 2008 as D 3311 – 08.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
4. Keywords
contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM
4.1 DWV; fittings; plastic; Schedule 40; thermoplastic
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
D 3311 – 09
TABLE 1 Bends, in. (mm)
Long Sweep
1 1 1 1
⁄4 Bend ⁄8 Bend ⁄6 Bend ⁄16 Bend
1
⁄4 Bend
Nominal Pipe Size
GG G G G
1 9 1 7 7
1 ⁄4 1 ⁄16 (40) 2 ⁄4 (57) 1 (25) ⁄8 (22) ⁄16 (11)
1 3 3 1 1
1 ⁄2 1 ⁄4 (44) 2 ⁄4 (70) 1 ⁄8 (29) 1 (25) ⁄2 (13)
5 1 1 5 11
22 ⁄16 (59) 3 ⁄4 (83) 1 ⁄2 (38) 1 ⁄16 (33) ⁄16 (17)
1 1 3 11 13
33 ⁄16 (78) 4 ⁄16 (103) 1 ⁄4 (44) 1 ⁄16 (43) ⁄16 (21)
7 15 3 1
43 ⁄8 (98) 4 ⁄16 (125) 2 ⁄16 (56) 2 ⁄16 (52) 1 (25)
3 1
6 5 (min) (127) 9 (229) 2 (min) (51) 3 ⁄8 (86) 1 ⁄2 (38)
1 1
8 6 (152) . . . 2 ⁄16 (52) . . . 1 ⁄2 (38)
TABLE 2 Bends with Inlets, in. (mm)
1
Long-Sweep ⁄4 Bend with Low Heel
1 1
⁄4 Bend with Low Heel Inlet Long-Sweep ⁄4 Bend with High Heel Inlet
Inlet
Nominal Pipe Size
GN G N G N GG
1 1 3 1 3
3by3by1 ⁄2 3 ⁄16 (78) 4 ⁄16 (106) 4 ⁄16 (103) 4 ⁄4 (121) . . . . . . . . .
1 7 1 15 1 5 1
3by3by2 3 ⁄16 (78) 4 ⁄16 (113) 4 ⁄16 (103) 4 ⁄16 (125) 4 ⁄16 (103) 5 ⁄8 (143) 2 ⁄4 (57)
7 7 15
4by4by2 3 ⁄8 (98) 5 ⁄16 (138) 4 ⁄16 (125) 6 (152) . . . . . . . . .
2

---------------------- Page: 2 ----------------------
D 3311 – 09
1
TABLE 3 Sanitary Tees, 45° Wyes, Combination Wyes and ⁄8 Bends, in. (mm)
Combination Wye and 1 8 Bend Single and
A /
Sanitary Tee Single and Double 45° Wye, Single and Double
Double
Nominal Pipe Size
GN GJ GN GJ GN GJ
1 3 9 1 9 7 15
1 ⁄4 ⁄4 (19) 1 ⁄16 (40) 1 ⁄16 (27) 2 ⁄16 (65) ⁄16 (11) 2 ⁄16 (75)
1 3 1 7 1 3
1 ⁄2 1 (25) 1 ⁄4 (44) 1 ⁄8 (29) 2 ⁄8 (73) ⁄2 (13) 3 ⁄8 (86)
3 5 3 5 1
21 ⁄8 (35) 2 ⁄16 (59) 1 ⁄8 (35) 3 ⁄8 (92) 1 (25) 4 ⁄2 (114)
13 1 5 1 5
31 ⁄16 (46) 3 ⁄16 (78) 1 ⁄8 (41) 5 (127) 1 ⁄8 (29) 6 ⁄16 (160)
1 7 7 3 13 5
42 ⁄4 (57) 3 ⁄8 (98) 1 ⁄8 (48) 6 ⁄8 (162) 1 ⁄16 (46) 8 ⁄8 (219)
BB
1 3
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
An American National Standard
Designation:D 3311–08 Designation: D 3311 – 09
Standard Specification for
1
Drain, Waste, and Vent (DWV) Plastic Fittings Patterns
This standard is issued under the fixed designation D 3311; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This specification provides standard fitting geometries and laying lengths for plastic fittings intended for use in drain, waste,
and vent applications. (See Specifications D 2661 and D 2665.)
1.2 Fittings meeting the requirements of this standard specification are designed for use with outside diameter controlled pipe.
The inside diameter can vary significantly as the wall thickness and outside diameter varies and therefore is not suitable for use
as a fitting socket.
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
2. Referenced Documents
2
2.1 ASTM Standards:
D 2661 Specification for Acrylonitrile-Butadiene-Styrene (ABS) Schedule 40 Plastic Drain, Waste, and Vent Pipe and Fittings
D 2665 Specification for Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings
3. Requirements
1
3.1 Fittings shall conform to the geometries and laying lengths as shown in Tables 1-46 and Fig. 1. Tolerances shall be 6 ⁄16
in. unless otherwise specified.
3.2 Spigot and hub dimensions shall conform to the requirements of the referencing standard.
3.3 The exact outside shape of a fitting is not determined by the outline drawings shown in this specification but rather by the
socket dimensions, wall thickness requirements, waterway, laying lengths, and any other critical dimensions that may be specified.
1
3.4 The pitch of sockets for patterns with 90° angles (except vent fittings) shall be ⁄4 in./ft or 1° 12 min.
3.5 On double reducing sanitary tees, the G2 dimension on branches will be calculated on the larger size and centerlines shall
remain the same for both branches.
3.6 All other dimensions, materials and property requirements shall be in conformance with the referencing standard.
4. Keywords
4.1 DWV; fittings; plastic; Schedule 40; thermoplastic
1
This specification is under the jurisdiction of ASTM Committee F17 on Plastic Piping Systems and is the direct responsibility of Subcommittee F17.63 on DWV.
Current edition approved Nov. 15, 2008. Published December 2008. Originally approved in 1974. Last previous edition approved in 2006 as D3311–06a.
Current edition approved May 1, 2009. Published June 2009. Originally approved in 1974. Last previous edition approved in 2008 as D 3311 – 08.
2
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at [e-mail]. For Annual Book ofASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
D 3311 – 09
TABLE 1 Bends, in. (mm)
Long Sweep
1 1 1 1
⁄4 Bend ⁄8 Bend ⁄6 Bend ⁄16 Bend
1
⁄4 Bend
Nominal Pipe Size
GG G G G
1 9 1 7 7
1 ⁄4 1 ⁄16 (40) 2 ⁄4 (57) 1 (25) ⁄8 (22) ⁄16 (11)
1 3 3 1 1
1 ⁄2 1 ⁄4 (44) 2 ⁄4 (70) 1 ⁄8 (29) 1 (25) ⁄2 (13)
5 1 1 5 11
22 ⁄16 (59) 3 ⁄4 (83) 1 ⁄2 (38) 1 ⁄16 (33) ⁄16 (17)
1 1 3 11 13
33 ⁄16 (78) 4 ⁄16 (103) 1 ⁄4 (44) 1 ⁄16 (43) ⁄16 (21)
7 15 3 1
43 ⁄8 (98) 4 ⁄16 (125) 2 ⁄16 (56) 2 ⁄16 (52) 1 (25)
3 1
6 5 (min) (127) 9 (229) 2 (min) (51) 3 ⁄8 (86) 1 ⁄2 (38)
1 1
8 6 (152) . . . 2 ⁄16 (52) . . . 1 ⁄2 (38)
TABLE 2 Bends with Inlets, in. (mm)
1
Long-Sweep ⁄4 Bend with Low Heel
1 1
⁄4 Bend with Low Heel Inlet Long-Sweep ⁄4 Bend with High Heel Inlet
Inlet
Nominal Pipe Size
GN G N G N GG
1 1 3 1 3
3by3by1 ⁄2 3 ⁄16 (78) 4 ⁄16 (106) 4 ⁄16 (103) 4 ⁄4 (121) . . . . . . . . .
1 7 1 15 1 5 1
3by3by2 3 ⁄16 (78) 4 ⁄16 (113) 4 ⁄16 (103) 4 ⁄16 (125) 4 ⁄16 (103) 5 ⁄8 (143) 2 ⁄4 (57)
7 7 15
4by4by2 3 ⁄8 (98) 5 ⁄16 (138) 4 ⁄16 (125) 6 (152) . . . . . . . . .
2

---------------------- Page: 2 ----------------------
D 3311 – 09
1
TABLE 3 Sanitary Tees, 45° Wyes, Combination Wyes and ⁄8 Bends, in. (mm)
Combination Wye and 1 8 Bend Single and
A /
Sanitary Tee Single and Double 45° Wye, Si
...