ASTM D2665-20
(Specification)Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings
Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings
ABSTRACT
This specification covers requirements and test methods for materials, dimensions and tolerances, pipe stiffness, crush resistance, impact resistance, hydrostatic burst resistance, and solvent cement for poly(vinyl chloride) plastic drain, waste, and vent pipe and fittings. The pipe and fittings covered are suitable for the drainage and venting of sewage and certain other liquid wastes. A form of marking is also included. The pipe and fittings shall be made of virgin PVC compounds of defined specification. The pipe shall conform to the required stiffness, deflection load and flattening. The fittings shall be subject to hydrostatic burst pressure. The pipe and fittings shall be subject to impact resistance test.
SCOPE
1.1 This specification covers requirements and test methods for materials, dimensions and tolerances, pipe stiffness, crush resistance, impact resistance, and solvent cement for poly(vinyl chloride) plastic drain, waste, and vent pipe and fittings. A form of marking is also included. Plastic which does not meet the material requirements specified in Section 5 is excluded. Installation procedures are given in the Appendix.
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.3 The text of this specification references notes, footnotes, and appendixes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification.
1.4 The following safety hazards caveat pertains only to the test methods portion, Section 7, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Relations
Buy Standard
Standards Content (Sample)
This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation:D2665 −20 An American National Standard
Standard Specification for
Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent
1
Pipe and Fittings
This standard is issued under the fixed designation D2665; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope* 2. Referenced Documents
2
1.1 This specification covers requirements and test methods 2.1 ASTM Standards:
for materials, dimensions and tolerances, pipe stiffness, crush D618Practice for Conditioning Plastics for Testing
resistance,impactresistance,andsolventcementforpoly(vinyl D1600TerminologyforAbbreviatedTermsRelatingtoPlas-
chloride)plasticdrain,waste,andventpipeandfittings.Aform tics
of marking is also included. Plastic which does not meet the D1784Classification System and Basis for Specification for
material requirements specified in Section 5 is excluded. Rigid Poly(Vinyl Chloride) (PVC) Compounds and Chlo-
Installation procedures are given in the Appendix. rinated Poly(Vinyl Chloride) (CPVC) Compounds
D2122Test Method for Determining Dimensions of Ther-
1.2 Thevaluesstatedininch-poundunitsaretoberegarded
moplastic Pipe and Fittings
as standard. The values given in parentheses are mathematical
D2412Test Method for Determination of External Loading
conversions to SI units that are provided for information only
Characteristics of Plastic Pipe by Parallel-Plate Loading
and are not considered standard.
D2444Practice for Determination of the Impact Resistance
1.3 Thetextofthisspecificationreferencesnotes,footnotes, of Thermoplastic Pipe and Fittings by Means of a Tup
and appendixes which provide explanatory material. These (Falling Weight)
D2564Specification for Solvent Cements for Poly(Vinyl
notesandfootnotes(excludingthoseintablesandfigures)shall
Chloride) (PVC) Plastic Piping Systems
not be considered as requirements of the specification.
D3311Specification for Drain, Waste, and Vent (DWV)
1.4 The following safety hazards caveat pertains only to the
Plastic Fittings Patterns
test methods portion, Section 7, of this specification: This
F402 Practice for Safe Handling of Solvent Cements,
standard does not purport to address all of the safety concerns,
Primers, and Cleaners Used for Joining Thermoplastic
if any, associated with its use. It is the responsibility of the user
Pipe and Fittings
of this standard to establish appropriate safety, health, and
F412Terminology Relating to Plastic Piping Systems
environmental practices and determine the applicability of
F1498SpecificationforTaperPipeThreads60°forThermo-
regulatory limitations prior to use.
plastic Pipe and Fittings
1.5 This international standard was developed in accor-
F1866SpecificationforPoly(VinylChloride)(PVC)Plastic
dance with internationally recognized principles on standard-
Schedule 40 Drainage and DWV Fabricated Fittings
ization established in the Decision on Principles for the
F2135Specification for Molded Drain, Waste, and Vent
Development of International Standards, Guides and Recom-
(DWV) Short-Pattern Plastic Fittings
mendations issued by the World Trade Organization Technical
Barriers to Trade (TBT) Committee.
3. Terminology
3.1 Definitions are in accordance with Terminology F412,
and abbreviations are in accordance with Terminology D1600,
unless otherwise specified.
1
This specification is under the jurisdiction ofASTM Committee F17 on Plastic
2
Piping Systems and is the direct responsibility of Subcommittee F17.63 on DWV. For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Current edition approved Aug. 1, 2020. Published August 2020. Originally contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
approved in 1968. Last previous edition approved in 2014 as D2665–14. DOI: Standards volume information, refer to the standard’s Document Summary page on
10.1520/D2665-20. the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
D2665−20
4. Significance and Use 6.2.2.5 For all fittings having taper pipe threads, threads
shall conform to Specification F1498 and be gaged in accor-
4.1 The requirements of this specification are intended to
dance with 7.5. Fittings of nominal sizes not given in Speci-
provide
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: D2665 − 14 D2665 − 20 An American National Standard
Standard Specification for
Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent
1
Pipe and Fittings
This standard is issued under the fixed designation D2665; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope*
1.1 This specification covers requirements and test methods for materials, dimensions and tolerances, pipe stiffness, crush
resistance, impact resistance, and solvent cement for poly(vinyl chloride) plastic drain, waste, and vent pipe and fittings. A form
of marking is also included. Plastic which does not meet the material requirements specified in Section 5 is excluded. Installation
procedures are given in the Appendix.
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
1.3 The text of this specification references notes, footnotes, and appendixes which provide explanatory material. These notes and
footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification.
1.4 The following safety hazards caveat pertains only to the test methods portion, Section 7, of this specification: This standard
does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this
standard to establish appropriate safety safety, health, and healthenvironmental practices and determine the applicability of
regulatory limitations prior to use.
1.5 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2
2.1 ASTM Standards:
D618 Practice for Conditioning Plastics for Testing
D1600 Terminology for Abbreviated Terms Relating to Plastics
D1784 Classification System and Basis for Specification for Rigid Poly(Vinyl Chloride) (PVC) Compounds and Chlorinated
Poly(Vinyl Chloride) (CPVC) Compounds
D2122 Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
D2412 Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading
D2444 Practice for Determination of the Impact Resistance of Thermoplastic Pipe and Fittings by Means of a Tup (Falling
Weight)
1
This specification is under the jurisdiction of ASTM Committee F17 on Plastic Piping Systems and is the direct responsibility of Subcommittee F17.63 on DWV.
Current edition approved May 1, 2014Aug. 1, 2020. Published June 2014August 2020. Originally approved in 1968. Last previous edition approved in 20122014 as
D2665 – 12.D2665 – 14. DOI: 10.1520/D2665-14.10.1520/D2665-20.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
D2665 − 20
D2564 Specification for Solvent Cements for Poly(Vinyl Chloride) (PVC) Plastic Piping Systems
D3311 Specification for Drain, Waste, and Vent (DWV) Plastic Fittings Patterns
F402 Practice for Safe Handling of Solvent Cements, Primers, and Cleaners Used for Joining Thermoplastic Pipe and Fittings
F412 Terminology Relating to Plastic Piping Systems
F1498 Specification for Taper Pipe Threads 60° for Thermoplastic Pipe and Fittings
F1866 Specification for Poly (Vinyl Chloride) (PVC) Plastic Schedule 40 Drainage and DWV Fabricated Fittings
F2135 Specification for Molded Drain, Waste, and Vent (DWV) Short-Pattern Plastic Fittings
3. Terminology
3.1 Definitions are in accordance with Terminology F412, and abbreviations are in accordance with Terminology D1600, unless
otherwise specified.
4.
...
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: D2665 − 20 An American National Standard
Standard Specification for
Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent
1
Pipe and Fittings
This standard is issued under the fixed designation D2665; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope* 2. Referenced Documents
2
1.1 This specification covers requirements and test methods 2.1 ASTM Standards:
for materials, dimensions and tolerances, pipe stiffness, crush D618 Practice for Conditioning Plastics for Testing
resistance, impact resistance, and solvent cement for poly(vinyl D1600 Terminology for Abbreviated Terms Relating to Plas-
chloride) plastic drain, waste, and vent pipe and fittings. A form tics
of marking is also included. Plastic which does not meet the D1784 Classification System and Basis for Specification for
material requirements specified in Section 5 is excluded. Rigid Poly(Vinyl Chloride) (PVC) Compounds and Chlo-
Installation procedures are given in the Appendix. rinated Poly(Vinyl Chloride) (CPVC) Compounds
D2122 Test Method for Determining Dimensions of Ther-
1.2 The values stated in inch-pound units are to be regarded
moplastic Pipe and Fittings
as standard. The values given in parentheses are mathematical
D2412 Test Method for Determination of External Loading
conversions to SI units that are provided for information only
Characteristics of Plastic Pipe by Parallel-Plate Loading
and are not considered standard.
D2444 Practice for Determination of the Impact Resistance
of Thermoplastic Pipe and Fittings by Means of a Tup
1.3 The text of this specification references notes, footnotes,
(Falling Weight)
and appendixes which provide explanatory material. These
D2564 Specification for Solvent Cements for Poly(Vinyl
notes and footnotes (excluding those in tables and figures) shall
not be considered as requirements of the specification. Chloride) (PVC) Plastic Piping Systems
D3311 Specification for Drain, Waste, and Vent (DWV)
1.4 The following safety hazards caveat pertains only to the
Plastic Fittings Patterns
test methods portion, Section 7, of this specification: This
F402 Practice for Safe Handling of Solvent Cements,
standard does not purport to address all of the safety concerns,
Primers, and Cleaners Used for Joining Thermoplastic
if any, associated with its use. It is the responsibility of the user
Pipe and Fittings
of this standard to establish appropriate safety, health, and
F412 Terminology Relating to Plastic Piping Systems
environmental practices and determine the applicability of
F1498 Specification for Taper Pipe Threads 60° for Thermo-
regulatory limitations prior to use.
plastic Pipe and Fittings
1.5 This international standard was developed in accor-
F1866 Specification for Poly (Vinyl Chloride) (PVC) Plastic
dance with internationally recognized principles on standard-
Schedule 40 Drainage and DWV Fabricated Fittings
ization established in the Decision on Principles for the
F2135 Specification for Molded Drain, Waste, and Vent
Development of International Standards, Guides and Recom-
(DWV) Short-Pattern Plastic Fittings
mendations issued by the World Trade Organization Technical
Barriers to Trade (TBT) Committee.
3. Terminology
3.1 Definitions are in accordance with Terminology F412,
and abbreviations are in accordance with Terminology D1600,
unless otherwise specified.
1
This specification is under the jurisdiction of ASTM Committee F17 on Plastic
2
Piping Systems and is the direct responsibility of Subcommittee F17.63 on DWV. For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Current edition approved Aug. 1, 2020. Published August 2020. Originally contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
approved in 1968. Last previous edition approved in 2014 as D2665 – 14. DOI: Standards volume information, refer to the standard’s Document Summary page on
10.1520/D2665-20. the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
D2665 − 20
4. Significance and Use 6.2.2.5 For all fittings having taper pipe threads, threads
shall conform to Specification F1498 and be gaged in accor-
4.1 The requirements of this specification are intended to
dance with 7.5. Fittings of nominal sizes not given in Speci-
provide pipe and fittings suitable for the drainage and ven
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.