ASTM F1412-22
(Specification)Standard Specification for Polyolefin Pipe and Fittings for Corrosive Waste Drainage Systems
Standard Specification for Polyolefin Pipe and Fittings for Corrosive Waste Drainage Systems
ABSTRACT
This specification covers the requirements for non-pressure polyolefin pipe and fittings for corrosive waste drainage systems. The pipe is produced in Schedule 40 and 80 IPS sizes in two polyolefins (polyethylene and polypropylene) that shall contain suitable stabilizers and antioxidants and may contain pigments and fillers not detrimental to the pipe and fittings. The specimens shall conform to the outside diameter; wall thickness; average waterway diameter; chemical resistance to acetic acid, acetone, methyl alcohol, ammonium hydroxide, nitric acid, and sodium hydroxide; water absorption; system integrity; flattening; and impact resistance requirements. Hydrostatic pressure tests shall be conducted on both the heat-fused and mechanical joints.
SCOPE
1.1 This specification covers requirements for non-pressure polyolefin pipe and fittings for corrosive waste drainage systems.
1.2 Pipe is produced in Schedule 40 and 80 IPS sizes, and in DR IPS sizes for two polyolefins, polyethylene (PE) and polypropylene (PP).
1.3 The interchangeability of pipe and fittings made by different manufacturers is not addressed in this specification. Transition fittings for joining pipe and fittings of different manufacturers is provided for in this specification.
1.4 Pipe and fittings are joined by the heat fusion method ( Practice D2657 for PP butt and saddle fusion, Practice F2620 for PE butt, saddle and socket fusion and Practice F1290 for polyolefin electrofusion) or by using mechanical joints recommended by the manufacturer.
1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.6 The following safety hazards caveat pertains only to the test method, Section 8, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Relations
Buy Standard
Standards Content (Sample)
This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation: F1412 − 22 An American National Standard
Standard Specification for
Polyolefin Pipe and Fittings for Corrosive Waste Drainage
1
Systems
This standard is issued under the fixed designation F1412; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* 2. Referenced Documents
2
1.1 This specification covers requirements for non-pressure 2.1 ASTM Standards:
polyolefin pipe and fittings for corrosive waste drainage D543 Practices for Evaluating the Resistance of Plastics to
systems. Chemical Reagents
D570 Test Method for Water Absorption of Plastics
1.2 Pipe is produced in Schedule 40 and 80 IPS sizes, and in
D618 Practice for Conditioning Plastics for Testing
DR IPS sizes for two polyolefins, polyethylene (PE) and
D2122 Test Method for Determining Dimensions of Ther-
polypropylene (PP).
moplastic Pipe and Fittings
1.3 The interchangeability of pipe and fittings made by
D2321 Practice for Underground Installation of Thermoplas-
different manufacturers is not addressed in this specification.
tic Pipe for Sewers and Other Gravity-Flow Applications
Transition fittings for joining pipe and fittings of different
D2412 Test Method for Determination of External Loading
manufacturers is provided for in this specification.
Characteristics of Plastic Pipe by Parallel-Plate Loading
1.4 Pipe and fittings are joined by the heat fusion method ( D2444 Practice for Determination of the Impact Resistance
of Thermoplastic Pipe and Fittings by Means of a Tup
Practice D2657 for PP butt and saddle fusion, Practice F2620
for PE butt, saddle and socket fusion and Practice F1290 for (Falling Weight)
D2657 Practice for Heat Fusion Joining of Polyolefin Pipe
polyolefin electrofusion) or by using mechanical joints recom-
mended by the manufacturer. and Fittings
D3311 Specification for Drain, Waste, and Vent (DWV)
1.5 The values stated in inch-pound units are to be regarded
Plastic Fittings Patterns
as standard. The values given in parentheses are mathematical
D3350 Specification for Polyethylene Plastics Pipe and Fit-
conversions to SI units that are provided for information only
tings Materials
and are not considered standard.
D4101 Classification System and Basis for Specification for
1.6 The following safety hazards caveat pertains only to the
Polypropylene Injection and Extrusion Materials
test method, Section 8, of this specification. This standard does
F412 Terminology Relating to Plastic Piping Systems
not purport to address all of the safety concerns, if any,
F1290 Practice for Electrofusion Joining Polyolefin Pipe and
associated with its use. It is the responsibility of the user of this
Fittings
standard to establish appropriate safety, health, and environ-
F1498 Specification for Taper Pipe Threads 60° for Thermo-
mental practices and determine the applicability of regulatory
plastic Pipe and Fittings
limitations prior to use.
F2620 Practice for Heat Fusion Joining of Polyethylene Pipe
1.7 This international standard was developed in accor-
and Fittings
dance with internationally recognized principles on standard-
2.2 Federal Standard:
3
ization established in the Decision on Principles for the
Fed. Std. No. 123 Marking for Shipment (Civil Agencies)
Development of International Standards, Guides and Recom-
2.3 Military Standard:
3
mendations issued by the World Trade Organization Technical
MIL-STD-129 Marking for Shipment and Storage
Barriers to Trade (TBT) Committee.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
1
This specification is under the jurisdiction of ASTM Committee F17 on Plastic contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
Piping Systems and is the direct responsibility of Subcommittee F17.63 on DWV. Standards volume information, refer to the standard’s Document Summary page on
Current edition approved Nov. 1, 2022. Published March 2023. Originally the ASTM website.
3
approved in 1992. Last previous edition approved in 2016 as F1412 – 16. DOI: DLA Document Services Building 4/D 700 Robbins Avenue Philadelphia, PA
10.1520/F1412-22 19111-5094 http://quicksearch.dla.mil/
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
F1412 − 22
TABLE 1 Outside Diameters and Tolerances for Polyolefin Pipe
2.4 Other Document:
4 in. (
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: F1412 − 16 F1412 − 22 An American National Standard
Standard Specification for
Polyolefin Pipe and Fittings for Corrosive Waste Drainage
1
Systems
This standard is issued under the fixed designation F1412; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope*
1.1 This specification covers requirements for non-pressure polyolefin pipe and fittings for corrosive waste drainage systems.
1.2 Pipe is produced in Schedule 40 and 80 IPS sizes, and in DR IPS sizes for two polyolefins, polyethylene (PE) and
polypropylene (PP).
1.3 The interchangeability of pipe and fittings made by different manufacturers is not addressed in this specification. Transition
fittings for joining pipe and fittings of different manufacturers is provided for in this specification.
1.4 Pipe and fittings are joined by the heat fusion method ( Practice D2657 for PP butt and saddle fusion, Practice F2620 for PE
butt, saddle and socket fusion and Practice F1290 for polyolefin electrofusion) or by using mechanical joints recommended by the
manufacturer.
1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
1.6 The following safety hazards caveat pertains only to the test method, Section 8, of this specification.This standard does not
purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to
establish appropriate safety and healthsafety, health, and environmental practices and determine the applicability of regulatory
limitations prior to use.
1.7 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2
2.1 ASTM Standards:
D543 Practices for Evaluating the Resistance of Plastics to Chemical Reagents
D570 Test Method for Water Absorption of Plastics
D618 Practice for Conditioning Plastics for Testing
D1600 Terminology for Abbreviated Terms Relating to Plastics
1
This specification is under the jurisdiction of ASTM Committee F17 on Plastic Piping Systems and is the direct responsibility of Subcommittee F17.63 on DWV.
Current edition approved Feb. 1, 2016Nov. 1, 2022. Published March 2016March 2023. Originally approved in 1992. Last previous edition approved in 20092016 as
F1412 – 09.F1412 – 16. DOI: 10.1520/F1412-1610.1520/F1412-22
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
F1412 − 22
D2122 Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
D2321 Practice for Underground Installation of Thermoplastic Pipe for Sewers and Other Gravity-Flow Applications
D2412 Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading
D2444 Practice for Determination of the Impact Resistance of Thermoplastic Pipe and Fittings by Means of a Tup (Falling
Weight)
D2657 Practice for Heat Fusion Joining of Polyolefin Pipe and Fittings
D3311 Specification for Drain, Waste, and Vent (DWV) Plastic Fittings Patterns
D3350 Specification for Polyethylene Plastics Pipe and Fittings Materials
D4101 Classification System and Basis for Specification for Polypropylene Injection and Extrusion Materials
F412 Terminology Relating to Plastic Piping Systems
F1290 Practice for Electrofusion Joining Polyolefin Pipe and Fittings
F1498 Specification for Taper Pipe Threads 60° for Thermoplastic Pipe and Fittings
F2620 Practice for Heat Fusion Joining of Polyethylene Pipe and Fittings
2.2 Federal Standard:
3
Fed. Std. No. 123 Marking for Shipment (Civil Agencies)
2.3 Military Standard:
3
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.