iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM F1718-01

(Specification)

Standard Specification for Rotary Positive Displacement Distillate Fuel Pumps

Standard Specification for Rotary Positive Displacement Distillate Fuel Pumps

SCOPE
1.1 This specification covers the requirements applicable to the design and construction of rotary positive displacement distillate fuel pumps for shipboard use.  
1.2 Lineal dimensions and units of force in this specification are expressed in inches and pounds respectively. A companion metric standard is in the process of preparation.

General Information

Status
Historical
Publication Date
09-Jun-2001
ICS
47.020.20 - Marine engines and propulsion systems
Technical Committee
F25 - Ships and Marine Technology
Drafting Committee
F25.11 - Machinery and Piping Systems
Current Stage
Ref Project

Relations

Replaces
ASTM F1718-99 - Standard Specification for Rotary Positive Displacement Distillate Fuel Pumps
Effective Date
10-Jun-2001
Replaced By
ASTM F1718-01(2006) - Standard Specification for Rotary Positive Displacement Distillate Fuel Pumps
Effective Date
01-Dec-2006

Buy Standard

ASTM F1718-01 - Standard Specification for Rotary Positive Displacement Distillate Fuel PumpsASTM F1718-01 - Standard Specification for Rotary Positive Displacement Distillate Fuel Pumps
PreviousNext
Technical specification
ASTM F1718-01 - Standard Specification for Rotary Positive Displacement Distillate Fuel Pumps
English language
7 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
An American National Standard
Designation: F 1718 – 01
Standard Specification for
1
Rotary Positive Displacement Distillate Fuel Pumps
This standard is issued under the fixed designation F 1718; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
5
1. Scope A563 Specification for Carbon and Alloy Steel Nuts
A564/A564M Specification for Hot-Rolled and Cold-
1.1 This specification covers the requirements applicable to
4
FinishedAge-Hardening Stainless Steel Bars and Shapes
the design and construction of rotary positive displacement
A 574 Specification for Alloy Steel Socket-Head Cap
distillate fuel pumps for shipboard use.
5
Screws
1.2 Linealdimensionsandunitsofforceinthisspecification
A582/A582M Specification for Free-Machining Stainless
are expressed as inches and pounds respectively.Acompanion
4
Steel Bars
metric standard is in the process of preparation.
A743/A743M SpecificationforCastings,Iron-Chromium,
2. Referenced Documents Iron-Chromium-Nickel, Corrosion-Resistant, for General
7
Application
2.1 ASTM Standards:
2
A747/A747M Specification for Steel Castings, Stainless,
A36/A36M Specification for Carbon Structural Steel
7
Precipitation Hardening
A53/A53M Specification for Pipe, Steel, Black and Hot-
8
3
B148 Specification for Aluminum-Bronze Sand Castings
Dipped, Zinc-Coated, Welded and Seamless
B150 Specification for Aluminum Bronze Rod, Bar, and
A106 Specification for Seamless Carbon Steel Pipe for
8
3
Shapes
High-Temperature Service
B209 Specification for Aluminum and Aluminum-Alloy
A193/A193M Specification for Alloy-Steel and Stainless
9
3
Sheet and Plate
Steel Bolting Materials for High-Temperature Service
B221 Specification for Aluminum-Alloy Extruded Bars,
A194/A194M Specification for Carbon and Alloy Steel
9
Rods, Wire, Profiles, and Tubes
Nuts for Bolts for High Pressure or High Temperature
3
B271 Specification for Copper-Base Alloy Centrifugal
Service, or Both
8
Castings
A240/A240M Specification for Heat-Resisting Chromium
B505 Specification for Copper-Base Alloy Continuous
and Chromium-Nickel Stainless Steel Plate, Sheet, and
8
4
Castings
Strip for Pressure Vessels
B584 Specification for Copper Alloy Sand Castings for
A269 Specification for Seamless and Welded Austenitic
8
3
General Applications
Stainless Steel Tubing for General Service
4
D1418 Practice for Rubber and Rubber Lattices— Nomen-
A276 Specification for Stainless Steel Bars and Shapes
10
clature
A312/A312M Specification for Seamless and Welded
3
D2000 Classification System for Rubber Products inAuto-
Austenitic Stainless Steel Pipes
11
motive Applications
A354 Specification for Quenched and Tempered Alloy
12
D3951 Practice for Commercial Packaging
Steel Bolts, Studs, and Other Externally Threaded Fasten-
5
F104 Classification System for Nonmetallic Gasket Mate-
ers
11
rials
A434 Specification for Steel Bars, Alloy, Hot-Wrought or
5
6
F467 Specification for Nonferrous Nuts for General Use
Cold-Finished, Quenched and Tempered
F468 Specification for Nonferrous Bolts, Hex Cap Screws,
A449 Specification for Quenched and Tempered Steel
5
5
and Studs for General Use
Bolts and Studs
F593 Specification for Stainless Steel Bolts, Hex Cap
5
Screws, and Studs
1 5
This specification is under the jurisdiction ofASTM Committee F25 on Ships
F594 Specification for Stainless Steel Nuts
and Marine Technology and is the direct responsibility of Subcommittee F25.11 on
Machinery.
Current edition approved June 10, 2001. Published September 2001. Originally
published as F1718-97. Previous edition F1718-99. 7
Annual Book of ASTM Standards, Vol 01.02.
2
Annual Book of ASTM Standards, Vol 01.04. 8
Annual Book of ASTM Standards, Vol 02.01.
3
Annual Book of ASTM Standards, Vol 01.01. 9
Annual Book of ASTM Standards, Vol 02.02.
4
Annual Book of ASTM Standards, Vol 01.03. 10
Annual Book of ASTM Standards, Vol 09.01.
5
Annual Book of ASTM Standards, Vol 15.08. 11
Annual Book of ASTM Standards, Vol 09.02.
6
Annual Book of ASTM Standards, Vol 01.05. 12
Annual Book of ASTM Standards, Vol 15.09.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
F 1718
F837 Specification for Stainless Steel Socket Head Cap 3. Terminology
5
Screws
3.1 Definitions:
5
F880 Specification for Stainless Steel Socket-Set Screws
3.1.1 capacity, n—the quantity of fluid actually delivered
5
F912 Specification for Alloy Steel Socket Set Screws
perunitoftimeattheratedspeed,includingboththeliquidand
F1511 Specification for Mechanical Seals for Shipboard
dissolvedorentrainedgases,understatedoperatingconditions.
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM F1309-23(Practice)
Standard Practice for Installation Procedures for Fitting Chocks to Marine Machinery Foundations

SIGNIFICANCE AND USE
3.1 This practice provides the three principal methods of fitting chocks to marine machinery foundations to ensure that the machinery is free of vibration and perfectly aligned after installation.  
3.1.1 The three principal methods of installing chocks described herein are as follows:
3.1.1.1 Type A—Epoxy-based resin, nonshrinking, and
3.1.1.2 Type B—Two-piece wedge chocks.
3.1.1.3 Type C—Solid, one-piece fitted chocks.
SCOPE
1.1 This practice covers the acceptable methods of fitting chocks to marine machinery foundations.  
1.2 The values stated in SI units shall be regarded as standard. The values in parentheses are for information only.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    6 pages
    English language
    sale 15% off
  • Standard
    6 pages
    English language
    sale 15% off
ASTM
ASTM F2798-09(2023)(Specification)
Standard Specification for Sealless Lube Oil Pump with Oil Through Motor for Marine Applications

SCOPE
1.1 This specification defines the requirements applicable to design, construction and testing of sealless, rotary positive displacement pumps with oil-through motors for ship lubricating oil service. The complete pump and motor assembly is referred to as canned lube oil pump (CLP). This specification applies to CLPs pumping oil with a SAE rating of 20–50.  
1.2 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    10 pages
    English language
    sale 15% off
ASTM
ASTM F2876-22(Practice)
Standard Practice for Thermal Rating and Installation of Internal Combustion Engine Packages for use in Hazardous Locations in Marine Applications

ABSTRACT
This practice covers methods of testing, rating, and installation of internal combustion engine packages used in hazardous areas in marine applications. The purpose of this practice is to thermally rate engine packages, and provide additional installation recommendations to reduce the risk of igniting ignitable mixtures that may be present near the hazardous areas of marine vessels. In this specification, only a marine engine suitable for the service, designed and constructed in accordance with the requirements of 3.2.1, is considered. Thermal rating of the engine is determined by the actual readings of engine and exhausts system temperatures within hazardous areas, as defined by the requirements and references in Practices 2.2 and 2.3 or as designated by the authority.
SCOPE
1.1 This practice covers the method of testing, rating and installation of internal combustion engine packages for use in hazardous areas in marine applications. The thermal rating of the engine is determined by the actual readings of engine and exhaust system temperatures within hazardous areas, as defined by references in Section 2 of this practice, or as designated by the authority having jurisdiction, or both. The goal of this practice is to thermally rate engine packages, and provide additional installation recommendations, in order to reduce the risk of igniting the ignitable mixtures that may be present within the hazardous areas of marine vessels.  
1.2 Only a marine engine suitable for the service, designed and constructed in conformance with the requirements of 3.1.2, is considered.  
1.3 The system of units in this practice shall be SI (metric) form, along with the standard (English) system equivalent placed in parentheses, for example, 20 °C (68 °F).  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM F1431-92(2021)(Specification)
Standard Specification for Water Trap for Diesel Exhaust

ABSTRACT
This specification covers the material, dimensions, and construction of a water trap for diesel exhaust. The diesel exhaust water trap system shall consist of a tank and baffles manufactured from a nickel-chromium-molybdenum-columbium alloy, with gaskets made of nonmetallic materials. A minimum of three baffles shall be installed. The traps shall withstand the maximum temperatures specified, be free of paint, and be so designed such as to prevent sea backwash from entering the diesel exhaust system. The trap and piping systems shall prevent dirt accumulation, with the welding being of small, even beading, free of slag and splatter. Pneumatic proof testing of each trap shall be performed with no visible seam leakage and shall conform to the requirements specified.
SCOPE
1.1 This specification covers the material, dimensions, and construction of diesel exhaust water traps, which shall be required whenever the exhaust is to be expelled through the hull of the vessel.  
1.2 The traps are designed to prevent sea backwash from entering the diesel exhaust system.  
1.3 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    3 pages
    English language
    sale 15% off
ASTM
ASTM F1338-91(2019)(Guide)
Standard Guide for Main Propulsion Medium Speed Marine Diesel Engines Covering Performance and Minimum Scope of Assembly

SIGNIFICANCE AND USE
4.1 Comparison of brake horsepower developed and of specific fuel consumption rates from engine to engine may be made by use of data based upon a standard for composition of an engine assembly.  
4.2 The purchaser of the engine assembly will be fully advised of the minimum scope of assembly which the purchaser may rightfully expect to be encompassed by a response to a request for quotation and to be delivered in response to a purchase order unless the engine builder in the proposal or in the offer to sell has clearly advised otherwise.  
4.3 It will be made apparent to the purchaser that additional auxiliary and accessory equipment will be needed to supplement the defined engine assembly when full consideration is given to the application of the engine assembly as a prime mover in a specific vessel.
SCOPE
1.1 This guide covers performance and minimum scope of assembly of all medium speed marine diesel engines intended for main propulsion of single or multiple screw propelled marine vessels or for vessels using other than screw propeller-type main propulsion.  
1.2 This guide is intended to supplement the regulations of legally constituted regulating authorities. In the event of any conflict, which may become apparent after publication of this guide, with such legally constituted regulations, the latter shall take precedence, as may be applicable within the jurisdiction of such authorities and specific to each case, unless such latter regulations are formally waived by proper cognizant authority.  
1.3 This guide is not intended to relieve the purchaser of the obligation fully to advise the engine builder of all of the purchaser’s unique operational considerations to allow those considerations to be satisfied.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    7 pages
    English language
    sale 15% off
ASTM
ASTM F1134-15(2019)(Specification)
Standard Specification for Insulation Resistance Monitor for Shipboard Electrical Motors and Generators

ABSTRACT
This specification covers monitoring devices (monitors) for the automatic detection and signaling of low insulation resistance values in idle electrical motors or generators, or both. Monitors are intended for permanent installation in both existing or new panels and controller enclosures designed for marine application. These insulation resistance monitors shall be classified in four types: Type I are alternating current generator monitors, Type II are alternating current generator monitors, Type III are direct current motor monitors, and Type IV are direct current generator monitors. The enclosure materials used in the construction of the monitors are to be flame-retardant and the current carrying terminals shall be made of corrosion resistant material. The monitors shall isolate their measuring circuit from the line voltage, while the motor is operating, by the use of an integral isolating relay. In the design of these monitors, environmental factors shall be considered: operating temperature range, sealing, inclination, humidity, and vibration. Also, the monitor relays, voltage characteristics and operating accuracy shall be considered in the design of these monitors. Each monitor shall be subjected to the following: visual and mechanical examination and operational test.
SCOPE
1.1 This specification covers monitoring devices (monitors) for the automatic detection and signaling of low insulation resistance values in idle electrical motors or generators, or both.  
1.2 Monitors are intended for permanent installation in both existing or new panels and controller enclosures designed for marine application.  
1.3 The values stated in SI units are to be regarded as standard. The values given in parentheses are mathematical conversions to inch-pound units that are provided for information only and are not considered standard.  
1.4 The following safety hazards caveat pertains only to the test method described in this specification:  This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    3 pages
    English language
    sale 15% off
ASTM
ASTM F1718-01(2019)(Specification)
Standard Specification for Rotary Positive Displacement Distillate Fuel Pumps

ABSTRACT
This specification covers the design and construction requirements of rotary positive displacement distillate fuel pumps intended for use in shipboard. Pumps covered by this specification are of Types II, III, IV, V, VIII, X, and XI and of sizes A-H. The pump shall be manufactured capable of sustaining operation in any direction up to a certain inclination, shall withstand environmental vibration induced by shipboard machinery and equipment, shall be driven by an electric motor, and besides distillate fuel, the pump shall also be used to pump aviation turbine fuel. Performance acceptance tests shall be performed, including mechanical running test, noise test, and hydrostatic test, and shall conform to the requirements specified.
SCOPE
1.1 This specification covers the requirements applicable to the design and construction of rotary positive displacement distillate fuel pumps for shipboard use.  
1.2 Lineal dimensions and units of force in this specification are expressed as inches and pounds respectively. A companion metric standard is in the process of preparation.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    7 pages
    English language
    sale 15% off
ASTM
ASTM F2361-18(Guide)
Standard Guide for Ordering Low Voltage (1000 VAC or Less) Alternating Current Electric Motors for Shipboard Service—Up to and Including Motors of 500 Horsepower

ABSTRACT
This guide provides the required basic ordering information for low voltage (1000 VAC or less, and up to and including motors of 500 hp) general-purpose (GP), commercial, universal, small and medium sized alternating current electric motors intended to drive common shipboard mechanical machinery such as fans, blowers, centrifugal and screw pumps. This guide does not address the ordering information for special-purpose (SP) motors, definite-purpose motors (for example, cryogenic service), or motors for use in hazardous (classified) locations as defined by the National Electrical Code (NFPA 70). The ordering checklist shall provide the following minimum information: electrical input; speed; power; enclosure; duty cycles; ambient temperature; insulation class; design class; service factor; drive method; mounting arrangement; mounting flange (end shield); rotation; motor conduit box location; closed-coupled; efficiency; and other special requirements.
SIGNIFICANCE AND USE
4.1 The selection criteria is to be applied for uses of (1) new motors and (2) replacement motors.  
4.2 For the selection of new or replacement motors, this practice defines the choice criteria in terms of the ordering data below.
SCOPE
1.1 This guide covers the required basic ordering information for low voltage (1000 VAC or less) general-purpose, commercial, universal, small-, and medium-sized alternating current electric motors for shipboard use, up to and including motors of 500 hp.  
1.2 The electric motors covered by this guide are general-purpose (GP) motors intended to drive common shipboard mechanical machinery such as fans, blowers, centrifugal and screw pumps.  
1.3 This guide is not intended to be used to order special-purpose (SP) motors or definite-purpose motors (for example, cryogenic service) or motors for use in hazardous (classified) locations as defined by the National Electrical Code (NFPA 70).  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    3 pages
    English language
    sale 15% off
  • Guide
    3 pages
    English language
    sale 15% off
ASTM
ASTM F1309-23(Practice)
Standard Practice for Installation Procedures for Fitting Chocks to Marine Machinery Foundations

SIGNIFICANCE AND USE
3.1 This practice provides the three principal methods of fitting chocks to marine machinery foundations to ensure that the machinery is free of vibration and perfectly aligned after installation.  
3.1.1 The three principal methods of installing chocks described herein are as follows:
3.1.1.1 Type A—Epoxy-based resin, nonshrinking, and
3.1.1.2 Type B—Two-piece wedge chocks.
3.1.1.3 Type C—Solid, one-piece fitted chocks.
SCOPE
1.1 This practice covers the acceptable methods of fitting chocks to marine machinery foundations.  
1.2 The values stated in SI units shall be regarded as standard. The values in parentheses are for information only.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    6 pages
    English language
    sale 15% off
  • Standard
    6 pages
    English language
    sale 15% off
ASTM
ASTM F2798-09(2023)(Specification)
Standard Specification for Sealless Lube Oil Pump with Oil Through Motor for Marine Applications

SCOPE
1.1 This specification defines the requirements applicable to design, construction and testing of sealless, rotary positive displacement pumps with oil-through motors for ship lubricating oil service. The complete pump and motor assembly is referred to as canned lube oil pump (CLP). This specification applies to CLPs pumping oil with a SAE rating of 20–50.  
1.2 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    10 pages
    English language
    sale 15% off