ASTM D476-15(2021)
(Classification)Standard Classification for Dry Pigmentary Titanium Dioxide Products
Standard Classification for Dry Pigmentary Titanium Dioxide Products
SIGNIFICANCE AND USE
3.1 This classification is given as an aid in determining the fitness for use of a titanium dioxide pigment for a coating application. It is limited to dry, hiding pigments. It excludes pigment dispersions, and non-hiding specialty titanium dioxide products.
SCOPE
1.1 This classification describes eight types of dry pigmentary titanium dioxide products, grouped by composition, typical end use application, and some performance properties.
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Relations
Standards Content (Sample)
This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation: D476 −15 (Reapproved 2021)
Standard Classification for
Dry Pigmentary Titanium Dioxide Products
This standard is issued under the fixed designation D476; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope application. It is limited to dry, hiding pigments. It excludes
pigment dispersions, and non-hiding specialty titanium dioxide
1.1 This classification describes eight types of dry pigmen-
products.
tary titanium dioxide products, grouped by composition, typi-
cal end use application, and some performance properties.
4. Basis for Classification
1.2 The values stated in SI units are to be regarded as
4.1 Titanium dioxide pigments can differ in many ways,
standard. No other units of measurement are included in this
including composition and performance. This classification
standard.
outlines differences between pigment types that should be
1.3 This international standard was developed in accor-
considered when selecting a product for a coating application.
dance with internationally recognized principles on standard-
A minimum number of properties are given to highlight major
ization established in the Decision on Principles for the
differences, while allowing maximum flexibility.
Development of International Standards, Guides and Recom-
mendations issued by the World Trade Organization Technical
5. Composition and Properties
Barriers to Trade (TBT) Committee.
5.1 Titanium Dioxide Pigments, should conform to the
requirements for composition prescribed in Table 1. They are
2. Referenced Documents
chemically prepared pigments consisting of anatase or rutile
2.1 ASTM Standards:
titanium dioxide with or without modifications with water-
D34 Guide for Chemical Analysis of White Pigments
insoluble oxides of aluminum, silicon, zinc, etc., or other
D153 Test Methods for Specific Gravity of Pigments
agents; these reagent materials are introduced specifically to
D185 Test Methods for Coarse Particles in Pigments
improve those properties for which the pigment is used. The
D280 Test Methods for Hygroscopic Moisture (and Other
titanium dioxide pigments shall be free of extenders such as
Matter Volatile Under the Test Conditions) in Pigments
barium sulfate, clay, magnesium silicate, whiting, etc.
D1394 Test Methods for Chemical Analysis of White Tita-
5.2 The desired properties of the pigment, other than as
nium Pigments
herein indicated, shall be subject to agreement between the
D2448 Test Method for Water-Soluble Salts in Pigments by
purchaser and the seller and shall be based on a satisfactory
Measuring the Specific Resistance of the Leachate of the
match between the submitted pigment sample and a previously
Pigment
agreed upon reference sample (see 6.1.6).
D3720 Test Method for Ratio of Anatase to Rutile in
Titanium Dioxide Pigments by X-Ray Diffraction
6. Test Methods
3. Significance and Use
6.1 Tests shall be conducted in accordance with the follow-
ing test methods. Test procedures not covered by ASTM test
3.1 This classification is given as an aid in determining the
methods shall be mutually agreed upon between the purchaser
fitness for use of a titanium dioxide pigment for a coating
and the seller.
6.1.1 Chemical Analysis—Guide D34 or Test Methods
This classification is under the jurisdiction of ASTM Committee D01 on Paint
D1394.
and Related Coatings, Materials, andApplications and is the direct responsibility of
6.1.2 Specific Gravity—Test Methods D153.
Subcommittee D01.31 on Pigment Specifications.
6.1.3 Coarse Particles—Test Methods D185.
Current edition approved June 1, 2021. Published June 2021. Originally
6.1.4 Moisture—Test Meth
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.