ASTM A612/A612M-12(2019)
(Specification)Standard Specification for Pressure Vessel Plates, Carbon Steel, High Strength, for Moderate and Lower Temperature Service
Standard Specification for Pressure Vessel Plates, Carbon Steel, High Strength, for Moderate and Lower Temperature Service
ABSTRACT
This specification covers killed carbon- manganese-silicon steel plates intended for welded pressure vessels in service at moderate and lower temperatures. As a steel making practice, the steel shall be killed and shall conform to specified fine austenitic grain size requirements. Plates are normally supplied in the as-rolled condition. Plates may be ordered normalized or stress relieved, or both. The steel shall conform to the required chemical compositions. The plates, as represented by the tension test specimens, shall conform to the mechanical property requirements.
SCOPE
1.1 This specification2 covers killed carbon-manganese-silicon steel plates intended for welded pressure vessels in service at moderate and lower temperatures.
1.2 The maximum thickness of plates supplied under this specification is 1 in. [25 mm].
1.3 For plates produced from coil and furnished without heat treatment or with stress relieving only, the additional requirements, including additional testing requirements and the reporting of additional test results, of Specification A20/A20M apply.
1.4 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification.
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:A612/A612M −12 (Reapproved 2019)
Standard Specification for
Pressure Vessel Plates, Carbon Steel, High Strength, for
Moderate and Lower Temperature Service
This standard is issued under the fixed designationA612/A612M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope A435/A435M Specification for Straight-Beam Ultrasonic
2 Examination of Steel Plates
1.1 This specification covers killed carbon-manganese-
A577/A577M Specification for Ultrasonic Angle-Beam Ex-
silicon steel plates intended for welded pressure vessels in
amination of Steel Plates
service at moderate and lower temperatures.
A578/A578M Specification for Straight-Beam Ultrasonic
1.2 The maximum thickness of plates supplied under this
Examination of Rolled Steel Plates for Special Applica-
specification is 1 in. [25 mm].
tions
1.3 For plates produced from coil and furnished without
heat treatment or with stress relieving only, the additional 3. General Requirements and Ordering Information
requirements,includingadditionaltestingrequirementsandthe
3.1 Material supplied to this product specification shall
reporting of additional test results, of Specification A20/A20M
conform to Specification A20/A20M. These requirements out-
apply.
line the testing and retesting methods and procedures, permit-
1.4 The values stated in either inch-pound units or SI units
ted variations in dimensions and mass, quality and repair of
are to be regarded separately as standard. Within the text, the defects, marking, loading, and ordering information.
SI units are shown in brackets. The values stated in each
3.2 In addition to the basic requirements of this
system are not exact equivalents; therefore, each system must
specification, certain supplementary requirements are available
be used independently of the other. Combining values from the
where additional control, testing, or examination is required to
two systems may result in nonconformance with the specifi-
meet end use requirements. The purchaser is referred to the
cation.
listed supplementary requirements in this specification and to
1.5 This international standard was developed in accor-
the detailed requirements in Specification A20/A20M.
dance with internationally recognized principles on standard-
3.3 Coils are excluded from qualification to this specifica-
ization established in the Decision on Principles for the
tion until they are processed into finished plates. Plates
Development of International Standards, Guides and Recom-
produced from coil means plates that have been cut to
mendations issued by the World Trade Organization Technical
individuallengthsfromcoil.Theprocessordirectlycontrols,or
Barriers to Trade (TBT) Committee.
is responsible for, the operations involved in the processing of
coils into finished plates. Such operations include decoiling,
2. Referenced Documents
leveling, cutting to length, testing, inspection, conditioning,
2.1 ASTM Standards:
heat treatment (if applicable), packaging, marking, loading for
A20/A20M SpecificationforGeneralRequirementsforSteel
shipment, and certification.
Plates for Pressure Vessels
NOTE 1—For plates produced from coil and furnished without heat
treatment or with stress relieving only, three test results are reported for
each qualifying coil. Additional requirements regarding plates from coil
are described in Specification A20/A20M.
This specification is under the jurisdiction of ASTM Committee A01 on Steel,
Stainless Steel and Related Alloys and is the direct responsibility of Subcommittee
3.4 If the requirements of this specification are in conflict
A01.11 on Steel Plates for Boilers and Pressure Vessels.
with the requirements of Specification A20/A20M, the require-
Current edition approved March 1, 2019. Published April 2019. Originally
approved in 1970. Last previous edition approved in 2012 as A612/A612M – 12.
ments of this specification shall prevail.
DOI: 10.1520/A0612_A0612M-12R19.
For ASME Boiler and Pressure Vessel Code applications see related Specifi-
4. Materials and Manufacture
cation SA-612/SA-612M in Section II of that Code.
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
4.1 Steelmaking Practice—The steel shall be killed and
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
shall conform to the fine austenitic grain size requirement of
Standards volume information, refer to the standard’s Document Summary page
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: A612/A612M − 12 A612/A612M − 12 (Reapproved 2019)
Standard Specification for
Pressure Vessel Plates, Carbon Steel, High Strength, for
Moderate and Lower Temperature Service
This standard is issued under the fixed designation A612/A612M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope*Scope
1.1 This specification covers killed carbon-manganese-silicon steel plates intended for welded pressure vessels in service at
moderate and lower temperatures.
1.2 The maximum thickness of plates supplied under this specification is 1 in. [25 mm].
1.3 For plates produced from coil and furnished without heat treatment or with stress relieving only, the additional requirements,
including additional testing requirements and the reporting of additional test results, of Specification A20/A20M apply.
1.4 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units
are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used
independently of the other. Combining values from the two systems may result in nonconformance with the specification.
1.5 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2.1 ASTM Standards:
A20/A20M Specification for General Requirements for Steel Plates for Pressure Vessels
A435/A435M Specification for Straight-Beam Ultrasonic Examination of Steel Plates
A577/A577M Specification for Ultrasonic Angle-Beam Examination of Steel Plates
A578/A578M Specification for Straight-Beam Ultrasonic Examination of Rolled Steel Plates for Special Applications
3. General Requirements and Ordering Information
3.1 Material supplied to this product specification shall conform to Specification A20/A20M. These requirements outline the
testing and retesting methods and procedures, permitted variations in dimensions and mass, quality and repair of defects, marking,
loading, and ordering information.
3.2 In addition to the basic requirements of this specification, certain supplementary requirements are available where additional
control, testing, or examination is required to meet end use requirements. The purchaser is referred to the listed supplementary
A20/A20M.
requirements in this specification and to the detailed requirements in Specification
3.3 Coils are excluded from qualification to this specification until they are processed into finished plates. Plates produced from
coil means plates that have been cut to individual lengths from coil. The processor directly controls, or is responsible for, the
operations involved in the processing of coils into finished plates. Such operations include decoiling, leveling, cutting to length,
testing, inspection, conditioning, heat treatment (if applicable), packaging, marking, loading for shipment, and certification.
NOTE 1—For plates produced from coil and furnished without heat treatment or with stress relieving only, three test results are reported for each
qualifying coil. Additional requirements regarding plates from coil are described in Specification A20/A20M.
This specification is under the jurisdiction of ASTM Committee A01 on Steel, Stainless Steel and Related Alloys and is the direct responsibility of Subcommittee A01.11
on Steel Plates for Boilers and Pressure Vessels.
Current edition approved May 1, 2012March 1, 2019. Published June 2012April 2019. Originally approved in 1970. Last previous edition approved in 20032012 as
A612/A612M – 03 (2007).A612/A612M – 12. DOI: 10.1520/A0612_A0612M-12.10.1520/A0612_A0612M-12R19.
For ASME Boiler and Pressure Vessel Code applications see related Specification SA-612/SA-612M in Section II of that Code.
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
A612/A612M − 12 (2019)
3.4 If the requirements of this specification are in conflict with the requirements of Specification A20/A20M, the requirements
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.