ASTM A1097/A1097M-22

Standard Specification for Steel Casing Pipe, Carbon, Electric-Fusion (Arc)-Welded (NPS 10 and Larger)

ABSTRACT
This specification applies to electric-fusion (arc)-welded straight seam or spiral seam steel casing pipe with diameter of 10 in. (254 mm) and larger (outside diameter as specified by purchaser) and wall thickness of 0.200 in. (5.1 mm) or greater. It shall be permissible to specify and furnish pipe having other dimensions provided such pipe complies with all other requirements of this specification. The pipe is intended for use as casing or encasement in horizontal underground boring, tunneling, or open trench applications.
SCOPE
1.1 This specification covers electric-fusion (arc)-welded straight seam or spiral seam steel casing pipe NPS 10 (Note 1) and larger in diameter (outside diameter as specified by purchaser) with wall thickness 0.200 in. [5.1 mm] or greater. It shall be permissible to specify and furnish pipe having other dimensions provided such pipe complies with all other requirements of this specification. The pipe is intended for use as casing or encasement in horizontal underground boring, tunneling, or open trench applications.  
1.2 This specification is expressed in both inch-pound units and in SI units; however, unless the purchase order or contract specifies the applicable M specification designation (SI units), the inch-pound units shall apply. The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.  
1.3 The text of this specification contains notes and footnotes that provide explanatory material. Such notes and footnotes, excluding those in tables and figures, do not contain any mandatory requirements.  
1.4 The following precautionary caveat pertains only to the test method portion, Sections 11, 12, and 13 of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
Note 1: The dimensionless designator NPS (nominal pipe size) has been substituted in this standard for such traditional terms as “nominal diameter,” “size,” and “nominal size.”  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

General Information

• Status: Published
• Publication Date: 31-Aug-2022
• ICS: 77.140.75 - Steel pipes and tubes for specific use
• Technical Committee: A01 - Steel, Stainless Steel and Related Alloys
• Drafting Committee: A01.09 - Carbon Steel Tubular Products

Standards Content (Sample)

This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation: A1097/A1097M −22
Standard Specification for
Steel Casing Pipe, Carbon, Electric-Fusion (Arc)-Welded
1
(NPS 10 and Larger)
This standard is issued under the fixed designation A1097/A1097M; the number immediately following the designation indicates the
year of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last
reapproval. A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* 1.5 This international standard was developed in accor-
dance with internationally recognized principles on standard-
1.1 This specification covers electric-fusion (arc)-welded
ization established in the Decision on Principles for the
straight seam or spiral seam steel casing pipe NPS 10 (Note 1)
Development of International Standards, Guides and Recom-
and larger in diameter (outside diameter as specified by
mendations issued by the World Trade Organization Technical
purchaser) with wall thickness 0.200 in. [5.1 mm] or greater. It
Barriers to Trade (TBT) Committee.
shall be permissible to specify and furnish pipe having other
dimensions provided such pipe complies with all other require-
2. Referenced Documents
ments of this specification. The pipe is intended for use as
casing or encasement in horizontal underground boring, 2
2.1 ASTM Standards:
tunneling, or open trench applications.
A36/A36M Specification for Carbon Structural Steel
1.2 This specification is expressed in both inch-pound units A515/A515M Specification for Pressure Vessel Plates, Car-
and in SI units; however, unless the purchase order or contract
bon Steel, for Intermediate- and Higher-Temperature Ser-
specifies the applicable M specification designation (SI units), vice
the inch-pound units shall apply. The values stated in either
A516/A516M Specification for Pressure Vessel Plates, Car-
inch-pound units or SI units are to be regarded separately as
bon Steel, for Moderate- and Lower-Temperature Service
standard. Within the text, the SI units are shown in brackets.
A572/A572M Specification for High-Strength Low-Alloy
The values stated in each system may not be exact equivalents;
Columbium-Vanadium Structural Steel
therefore,eachsystemshallbeusedindependentlyoftheother.
A370 Test Methods and Definitions for Mechanical Testing
Combining values from the two systems may result in noncon-
of Steel Products
formance with the standard.
A941 TerminologyRelatingtoSteel,StainlessSteel,Related
Alloys, and Ferroalloys
1.3 The text of this specification contains notes and foot-
A1011/A1011M Specification for Steel, Sheet and Strip,
notes that provide explanatory material. Such notes and
Hot-Rolled, Carbon, Structural, High-Strength Low-
footnotes, excluding those in tables and figures, do not contain
any mandatory requirements. Alloy, High-Strength Low-Alloy with Improved
Formability, and Ultra-High Strength
1.4 The following precautionary caveat pertains only to the
A1018/A1018M Specification for Steel, Sheet and Strip,
test method portion, Sections 11, 12, and 13 of this specifica-
Heavy-Thickness Coils, Hot-Rolled, Carbon,
tion. This standard does not purport to address all of the safety
Commercial, Drawing, Structural, High-Strength Low-
concerns, if any, associated with its use. It is the responsibility
Alloy, High-Strength Low-Alloy with Improved
of the user of this standard to establish appropriate safety,
Formability, and Ultra-High Strength
health, and environmental practices and determine the appli-
E29 Practice for Using Significant Digits in Test Data to
cability of regulatory limitations prior to use.
Determine Conformance with Specifications
NOTE 1—The dimensionless designator NPS (nominal pipe size) has
3
2.2 AWS Standard:
been substituted in this standard for such traditional terms as “nominal
diameter,” “size,” and “nominal size.” D1.1/D1.1M Structural Welding Code – Steel
1 2
This specification is under the jurisdiction of ASTM Committee A01 on Steel, For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Stainless Steel and Related Alloys and is the direct responsibility of Subcommittee contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM
A01.09 on Carbon Steel Tubular Products. Standards volume information, refer to the standard’s Document Summary page on
Current edition approved Sept. 1, 2022. Published September 2022. Originally the ASTM website.
3
approved in 2016. Last previous edition approved in 2016 as A1097 – 16. DOI: Available from American Welding Society (AWS), 8669 NW 36 St., #130,
10.1520/A1097_A1097M-22. Miami, FL 33166-6672, http://www.aws.org.
*A Summary of Changes section appear
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: A1097 − 16 A1097/A1097M − 22
Standard Specification for
Steel Casing Pipe, Carbon, Electric-Fusion (Arc)-Welded
1
(Outside Diameter of 10 in. (NPS 10 and Larger)
This standard is issued under the fixed designation A1097;A1097/A1097M; the number immediately following the designation indicates
the year of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last
reapproval. A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope Scope*
1.1 This specification covers electric-fusion (arc)-welded straight seam or spiral seam steel casing pipe NPS 10 in.(Note 1 (254
mm) ) and larger in diameter (outside diameter as specified by purchaser) with wall thickness 0.200 in. (5.1 mm)[5.1 mm] or
greater. It shall be permissible to specify and furnish pipe having other dimensions provided such pipe complies with all other
requirements of this specification. The pipe is intended for use as casing or encasement in horizontal underground boring,
tunneling, or open trench applications.
1.2 This specification is expressed in both inch-pound units and in SI units; however, unless the purchase order or contract
specifies the applicable M specification designation (SI units), the inch-pound units shall apply. The values stated in either
inch-pound units or SI units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI
units that are provided for information only and are not considered separately as standard. Within the text, the SI units are shown
in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of
the other. Combining values from the two systems may result in nonconformance with the standard.
1.3 The text of this specification contains notes and footnotes that provide explanatory material. Such notes and footnotes,
excluding those in tables and figures, do not contain any mandatory requirements.
1.4 The following precautionary caveat pertains only to the test method portion, Sections 11, 12, and 13 of this specification.
This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the
user of this standard to establish appropriate safety safety, health, and healthenvironmental practices and determine the
applicability of regulatory limitations prior to use.
NOTE 1—The dimensionless designator NPS (nominal pipe size) has been substituted in this standard for such traditional terms as “nominal diameter,”
“size,” and “nominal size.”
1.5 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2
2.1 ASTM Standards:
1
This specification is under the jurisdiction of ASTM Committee A01 on Steel, Stainless Steel and Related Alloys and is the direct responsibility of Subcommittee A01.09
on Carbon Steel Tubular Products.
Current edition approved Sept. 15, 2016Sept. 1, 2022. Published October 2016September 2022. Originally approved in 2016. Last previous edition approved in 2016 as
A1097 – 16. DOI: 10.1520/A1097-16.10.1520/A1097_A1097M-22.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
A1097/A1097M − 22
A36/A36M Specification for Carbon Structural Steel
A515/A515M Specification for Pressure Vessel Plates, Carbon Steel, for Intermediate- and Higher-Temperature Service
A516/A516M Specification for Pressure Vessel Plates, Carbon Steel, for Moderate- and Lower-Temperature Service
A572/A572M Specification for High-Strength Low-Alloy Columbium-Vanadium Structural Steel
A370 Test Methods and Definitions for Mechanical Testing of Steel Products
A941 Terminology Relating to Steel, Stainless Steel, Related Alloys, and Ferroalloys
A1011/A1011M Specification for Steel, Sheet and Strip, Hot-Rolled, Carbon, St
...