77.140.01 - Iron and steel products in general
ICS 77.140.01 Details
Iron and steel products in general
Stahl- und Eisenprodukte im allgemeinen
Produits en fonte et produits en acier en général
Železni in jekleni izdelki na splošno
General Information
e-Library Subscription
Create subscription and get permanent access to documents within 77.140.01 - Iron and steel products in general
Currently subscription includes documents marked with .We are working on making all documents available within the subscription.
This document applies to bright steel products in the drawn, turned or ground condition delivered in straight lengths. This document is mainly applied to stainless steels of EN 10088-3 and other product standards, e.g. tool steels, roller bearing steels. This document can also be used for cold heading steels both in the form of bars and wire.
The non-alloy and alloy steels of EN 10277 are no longer included.
This document does not cover cold rolled products and cut lengths produced from strip or sheet by cutting.
- Standard13 pagesEnglish languagesale 10% offe-Library read for1 day
This document lists, under Clause 4, the European Standards which are currently available for the determination of the chemical composition of steels and cast irons.
In Clause 5, this document provides details on the range of application and gives the principle of the method described in each standard.
Items which are under preparation as European Standards or as CEN Technical Reports by ECISS/TC 102 are available on the webpage of CEN, through the following link: https://standards.cen.eu/dyn/www/f?p=204:22:0::::FSP_ORG_ID:733643&cs=123E58BF77E3DE921F548B80C5FF2E5D4.
Annex A gives a list of other European Standards and CEN Technical Reports applicable for the determination of the chemical composition of steels and cast irons.
Annex B gives a list of withdrawn Euronorms, together with the corresponding replacement European Standards, if any.
Annex C shows graphical representations of the content ranges of the methods listed in this document. Figure C.1 gives the content ranges of the referee methods, Figure C.2 gives the content ranges of the routine methods and Figure C.3 represents the fields of application of all the methods described.
Annex D provides a trilingual key of the abbreviations used in the Figures given in Annex C.
NOTE Three methods applicable for the analysis of some ferro-alloys are listed in Annex A.
- Technical report37 pagesEnglish languagesale 10% offe-Library read for1 day
This document lists, under Clause 4, the European Standards which are currently available for the determination of the chemical composition of steels and cast irons.
In Clause 5, this document provides details on the range of application and gives the principle of the method described in each standard.
Items which are under preparation as European Standards or as CEN Technical Reports by ECISS/TC 102 are available on the webpage of CEN, through the following link: https://standards.cen.eu/dyn/www/f?p=204:22:0::::FSP_ORG_ID:733643&cs=123E58BF77E3DE921F548B80C5FF2E5D4.
Annex A gives a list of other European Standards and CEN Technical Reports applicable for the determination of the chemical composition of steels and cast irons.
Annex B gives a list of withdrawn Euronorms, together with the corresponding replacement European Standards, if any.
Annex C shows graphical representations of the content ranges of the methods listed in this document. Figure C.1 gives the content ranges of the referee methods, Figure C.2 gives the content ranges of the routine methods and Figure C.3 represents the fields of application of all the methods described.
Annex D provides a trilingual key of the abbreviations used in the Figures given in Annex C.
NOTE Three methods applicable for the analysis of some ferro-alloys are listed in Annex A.
- Technical report37 pagesEnglish languagesale 10% offe-Library read for1 day
- Standard1 pageEnglish languagesale 15% off
This document specifies the method for the verification of models for the determination of the property data of steels and the validation of the modelling process. It is applicable where modelling of mechanical or physical properties is used to substitute conventional testing for specific inspection. Models can be based on statistical data, thermo-physical data or indirect measurement (e.g. measurement of magnetic or ultrasonic data), or a combination of these methods.
This document applies only for providing the properties of rolled and/or heat-treated products such as plates, sheets, strip, sections and bars.
This document is used to demonstrate the ability of the model to supply property data which is equivalent to data, measured by conventional testing.
Any self-learning system is excluded from the scope.
NOTE A self-learning, in the spirit of an auto-adaptive model, is a model which changes its internal parameters by itself.
- Standard19 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies requirements for the design, materials, manufacturing and testing of pressure vessels and pressure vessel parts intended for use with a maximum allowable pressure, PS, equal or less than:
- 100 bar when containing gases or liquids in group 1 or 2
- 1000 bar when containing liquids in group 2 only.
and shell wall thicknesses not exceeding 60 mm, which are constructed of ferritic or austenitic spheroidal graphite cast iron. The thickness limitation of the shell does not apply to thickness of flanges, reinforcements, bosses etc.
NOTE 1 Austenitic spheroidal graphite cast iron grades are principally used for high and low temperature applications and for their corrosion resistance properties.
NOTE 2 The allowable grades of spheroidal graphite cast iron are listed in Tables 5.1-1 and 5.1-2. Service conditions are given in Clause 4.
This document, EN 13445-6, does not include lamellar graphite cast iron grades for ferritic and austenitic grades with, with an elongation after fracture equal or less than 15 % which are explicitly excluded. Requirements for the use of cast irons with an elongation after fracture equal or less than 15 % are given in EN 15776.
- Standard63 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies requirements for flat and long products of hot-rolled weldable fine-grain structural steels in the as-rolled (for SG grades only), normalized/normalized rolled and thermomechanical processed delivery conditions. It applies to steel plates rolled on a reversing mill, wide flats, hot-rolled sections and bars, which are intended for use in heavily loaded parts of welded or bolted structures. This document covers 13 grades and 6 qualities. Grades S275, S355, S390, S420, S460 and S500 are covered in Annex A. Grades SG245, SG290, SG325, SG345, SG365, SG415 and SG460 are covered in Annex B. Not all grades are available in all qualities, and some qualities have Charpy V-notch requirements. The steels specified in this document are applicable to hot-rolled plates, wide flats, sections and bars with a minimum nominal thickness of 3 mm and a maximum nominal thickness of 250 mm for grades S275N, S355N, S390N, S420N and S460N, a maximum nominal thickness of 150 mm for grades S275M, S355M, S390M, S420M, S460M, and S500M, a maximum nominal thickness of 200 mm for grades SG245, SG325 and SG415, a maximum nominal thickness of 100 mm for grades SG345, SG365 and SG460, and a maximum nominal thickness of 40 mm for grade SG290. This document does not include the following structural steels, some of which are covered by other International Standards: — Sheet and strip — refer to ISO TC 17/SC 12, Continuous mill flat rolled products; — Tubular products — refer to ISO TC 5/SC 1, Steel tubes. NOTE 1 Lists of standards covered by ISO/TC 17/SC 12 and ISO/TC 5/SC 1 are available on the ISO website. NOTE 2 In all parts of ISO 630, the term of "thickness" is considered as "nominal thickness", unless otherwise stated.
- Standard17 pagesEnglish languagesale 15% off
- Standard17 pagesEnglish languagesale 15% off
This document specifies qualities for high-yield-strength quenched and tempered structural steels. It applies to steel plates and wide flats rolled on a reversing mill which are used in the quenched and tempered condition and normally intended for welded or bolted structures. This document covers 10 grades and 5 qualities. Grades S460Q, S500Q, S550Q, S620Q, S690Q, S890Q and S960Q are covered in Annex A. Grades SG460Q, SG500Q, and SG700Q are covered in Annex B. Not all grades are available in all qualities, and some qualities have Charpy V-notch requirements. The steels specified in this document are applicable to hot-rolled flat products with a minimum nominal thickness of 3 mm and a maximum nominal thickness of 200 mm for grades S460Q, S500Q, S550Q, S620Q and S690Q, a maximum nominal thickness of 125 mm for grades S890Q and S960Q, a maximum nominal thickness of 100 mm for grades SG460Q and SG500Q and a maximum nominal thickness of 150 mm for grade SG700Q. This document does not include the following structural steels, some of which are covered by other International Standards: — Sheet and strip — refer to ISO TC 17/SC 12, Continuous mill flat rolled products; — Tubular products — refer to ISO TC 5/SC 1, Steel tubes. NOTE 1 Lists of standards covered by ISO/TC 17/SC 12 and ISO/TC 5/SC 1 are available on the ISO website. NOTE 2 In all parts of ISO 630, the term of "thickness" is considered as "nominal thickness", unless otherwise stated.
- Standard14 pagesEnglish languagesale 15% off
- Standard14 pagesEnglish languagesale 15% off
This document specifies the general technical delivery conditions for steel flat and long products (plates/ sections/wide flats and bars) used principally for general-purpose structural steels. The steels specified in this document are intended for use in welded or bolted structures. The specific requirements for structural steels are given in the individual parts of ISO 630. This document does not include the following structural steels, some of which are covered by other International Standards: — sheet and strip: refer to ISO TC 17/SC 12 “Continuous mill flat rolled products”; — tubular products: refer to ISO TC 5/SC 1 “Steel tubes”. NOTE 1 Lists of standards covered by ISO/TC 17/SC 12 and ISO/TC 5/SC 1 are available on the ISO website. NOTE 2 In all parts of ISO 630, the term of "thickness" is considered as "nominal thickness", unless otherwise stated.
- Standard12 pagesEnglish languagesale 15% off
- Standard12 pagesEnglish languagesale 15% off
This document specifies qualities for steels for general structural use. This document applies to steel plates rolled on a reversing mill, wide flats, hot-rolled sections and bars, which are used in the as-delivered condition and normally intended for welded or bolted structures. This document covers 8 steel grades and 4 qualities. Grades S235, S275, S355, and S460 are covered in Annex A. Grades SG205, SG250, SG285 and SG345 are covered in Annex B. Not all grades are available in all qualities, and some qualities have Charpy V‑notch requirements. The steels specified in this document are applicable to hot-rolled flat products and sections with: — thicknesses ≥ 3 mm and ≤ 150 mm for long products of steel grade S460 all qualities; — thicknesses ≥ 3 mm and ≤ 250 mm for long products or ≤ 400 mm for flat products of all other grades and qualities; and no restriction on nominal thickness for grades SG205, SG250, SG285, and SG345 for flat products, sections and long products. This document does not include the following structural steels, some of which are covered by other International Standards: — sheet and strip: refer to ISO TC 17/SC 12 “Continuous mill flat rolled products”; — tubular products: refer to ISO TC 5/SC 1 “Steel tubes”. NOTE 1 Lists of standards covered by ISO/TC 17/SC 12 and ISO/TC 5/SC 1 are available on the ISO website. NOTE 2 In all parts of ISO 630, the term of "thickness" is considered as "nominal thickness", unless otherwise stated.
- Standard15 pagesEnglish languagesale 15% off
- Standard15 pagesEnglish languagesale 15% off
This document describes the classification, method of sample preparation, certification main rules and certificate content of the EURONORM-CRMs.
It also details the sample presentation of the various producers' organizations and the distributing sources.
- Technical report11 pagesEnglish languagesale 10% offe-Library read for1 day
This document describes the classification, method of sample preparation, certification main rules and certificate content of the EURONORM-CRMs.
It also details the sample presentation of the various producers' organizations and the distributing sources.
- Technical report11 pagesEnglish languagesale 10% offe-Library read for1 day
ISO 4885:2018 defines important terms used in the heat treatment of ferrous materials.
NOTE The term ferrous materials include products and workpieces of steel and cast iron.
Annex A provides an alphabetical list of terms defined in this document, as well as their equivalents in French, German, Chinese and Japanese.
Table 1 shows the various iron-carbon (Fe-C) phases.
- Standard48 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies through thickness properties and associated test methods for flat products and sections of steel.
This document may be applied as a supplement to all product standards for flat products and sections of fully killed steels, except stainless steels. It covers products having a thickness between 15 mm and 400 mm inclusive of steels with a specified minimum upper yield strength ReH or proof strength Rp0,2 ≤ 960 MPa ) for which improved through thickness properties are required.
The application of this document to other steel types shall be the subject of agreement at the time of the order.
The application of this document to products with thickness between 10 mm ≤ t <15 mm shall be the subject of agreement at the time of the order. See option 1.
The application of this document to products with thickness t > 400 mm shall be the subject of agreement at the time of the order. See option 3.
- Standard16 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies the technical delivery requirements for bright steel bars in the drawn or peeled/turned condition and they are intended for mechanical purposes, for example for machine parts. The bright bars are subdivided into the following steel types:
a) non-alloy general engineering steels;
b) non-alloy free-cutting steels;
c) non-alloy and alloy case-hardening steels;
d) non-alloy and alloy steels for quenching and tempering.
Bright steel products of stainless steels are to be found in EN 10088-3.
In addition to this standard, the general technical delivery requirements of EN 10021 are applicable.
- Standard53 pagesEnglish languagesale 10% offe-Library read for1 day
ISO 4885:2018 defines important terms used in the heat treatment of ferrous materials. NOTE The term ferrous materials include products and workpieces of steel and cast iron. Annex A provides an alphabetical list of terms defined in this document, as well as their equivalents in French, German, Chinese and Japanese. Table 1 shows the various iron-carbon (Fe-C) phases.
- Standard41 pagesEnglish languagesale 15% off
- Standard41 pagesEnglish languagesale 15% off
- Standard42 pagesFrench languagesale 15% off
- Standard42 pagesFrench languagesale 15% off
This document specifies requirements for the identification, location and preparation of samples and test
pieces intended for mechanical tests on steel sections, bars, rod, flat products and tubular products as
defined in ISO 6929. If agreed in the order, this document can also apply to other metallic products. These
samples and test pieces are for use in tests that are carried out in conformity with the methods specified
in the product or material standard or, in the absence of this, in the standard for the test method.
Where the requirements of the order or product standard differ from those given in this document,
then the requirements of the order or product standard apply.
- Standard29 pagesEnglish languagesale 10% offe-Library read for1 day
ISO 6929:2013 defines terms for steel products according to their a) stage of manufacture, b) shape and dimensions, and c) appearance.
- Standard40 pagesEnglish languagesale 15% off
- Standard40 pagesEnglish languagesale 15% off
- Standard40 pagesEnglish languagesale 15% off
- Standard40 pagesRussian languagesale 15% off
- Standard50 pagesRussian languagesale 15% off
ISO 10474:2013 defines the different types of inspection documents supplied to the purchaser, in accordance with the requirements of the order, for the delivery of steel products. ISO 10474:2013 is to be used in conjunction with other International Standards which specify the general technical delivery conditions: ? for steel and steel products, see ISO 404; ? for steel castings, see ISO 4990.
- Standard4 pagesEnglish languagesale 15% off
- Standard6 pagesRussian languagesale 15% off
ISO 404:2013 specifies the general technical delivery requirements for all steel products covered by ISO 6929, with the exception of steel castings and powder metallurgical products. ISO 10474 describes the inspection documents to be used. Where the delivery requirements agreed upon for the order or specified in the appropriate product or material standard differ from the general technical delivery requirements defined in ISO 404:2013, then it is the requirements agreed for ordering or specified in the appropriate product or material standard that apply.
- Standard14 pagesEnglish languagesale 15% off
1.1 This European Standard covers the grades of wrought steels and alloys listed in Table 1 and Table 2, which are usually employed for components and equipment, for which the main requirement is their creep resistance under mechanical long-time stressing at temperatures above 500 C.
NOTE Heat resisting grades given in EN 10095 [9] may also be used for similar applications if so agreed.
1.2 This European Standard specifies the technical delivery conditions for semi-finished products, for hot or cold rolled sheet/plate and strip, hot or cold formed (cold drawn) bars, rods, wire and sections.
1.3 The general technical delivery conditions specified in EN 10021:2006 apply in addition to the specifications of this European Standard, unless otherwise specified in this European Standard.
1.4 This European Standard does not apply to components manufactured by further processing the product forms listed in 1.2 with quality characteristics altered as a result of such further processing.
1.5 This European Standard shall not be used for aerospace and pressure purposes.
1.6 For steels and alloys with similar chemical composition, but intended for different applications, see the Bibliography.
- Standard46 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard defines terms for steel products according to:
a) shape and dimensions; and
b) appearance and surface condition.
NOTE 1 Although the products are generally defined independently of their end uses or manufacturing processes, it has sometimes been necessary to make reference to these criteria.
NOTE 2 All dimensions given in this European Standard are nominal.
- Standard44 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies the general technical delivery conditions for all steel products covered by
EN 10079 with the exception of steel castings and powder metallurgical products.
Where the delivery requirements agreed for the order or specified in the appropriate product standard differ from the general technical delivery conditions defined in this European Standard, then the requirements agreed for the order or specified in the appropriate product standard apply.
NOTE Inspection documents are covered by EN 10168 and EN 10204.
- Standard17 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard defines terms for steel products according to:
a) shape and dimensions; and
b) appearance and surface condition.
NOTE 1 Although the products are generally defined independently of their end uses or manufacturing processes, it has sometimes been necessary to make reference to these criteria.
NOTE 2 All dimensions given in this European Standard are nominal.
- Standard44 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies the general technical delivery conditions for all steel products covered by
EN 10079 with the exception of steel castings and powder metallurgical products.
Where the delivery requirements agreed for the order or specified in the appropriate product standard differ from the general technical delivery conditions defined in this European Standard, then the requirements agreed for the order or specified in the appropriate product standard apply.
NOTE Inspection documents are covered by EN 10168 and EN 10204.
- Standard17 pagesEnglish languagesale 10% offe-Library read for1 day
1.1 This European Standard specifies the different types of inspection documents supplied to the purchaser, in accordance with the requirements of the order, for the delivery of all metallic products e.g. plates, sheets, bars, forgings, castings, whatever their method of production.
1.2 This standard may also apply to non-metallic products.
1.3 This standard is used in conjunction with the product specifications which specify the technical delivery conditions of the products.
NOTE 1 The list of information that may be included in the inspection documents can be found in appropriate documents, e.g. prEN 10168 for steel.
NOTE 2 Annex A gives a summary of the different inspection documents.
- Standard10 pagesEnglish languagesale 10% offe-Library read for1 day
- Standard10 pagesEnglish languagesale 10% offe-Library read for1 day
- Standard9 pagesGerman languagesale 10% offe-Library read for1 day
- Standard9 pagesGerman languagesale 10% offe-Library read for1 day
This European Standard lists the information that may be communicated and includes a brief description in the inspection documents of iron and steel products as described in EN 10021 and EN 10204. By laying down standardized designations and definitions for information likely to appear in inspection documents and by introducing code numbers for each of the designated sections, this European Standard intends to contribute to the elimination of communication difficulties in European trade.
- Standard12 pagesEnglish languagesale 10% offe-Library read for1 day
1.1 This European Standard specifies the different types of inspection documents supplied to the purchaser, in accordance with the requirements of the order, for the delivery of all metallic products e.g. plates, sheets, bars, forgings, castings, whatever their method of production.
1.2 This standard may also apply to non-metallic products.
1.3 This standard is used in conjunction with the product specifications which specify the technical delivery conditions of the products.
NOTE 1 The list of information that may be included in the inspection documents can be found in appropriate documents, e.g. prEN 10168 for steel.
NOTE 2 Annex A gives a summary of the different inspection documents.
- Standard10 pagesEnglish languagesale 10% offe-Library read for1 day
- Standard10 pagesEnglish languagesale 10% offe-Library read for1 day
- Standard9 pagesGerman languagesale 10% offe-Library read for1 day
- Standard9 pagesGerman languagesale 10% offe-Library read for1 day
This European Standard lists the information that may be communicated and includes a brief description in the inspection documents of iron and steel products as described in EN 10021 and EN 10204. By laying down standardized designations and definitions for information likely to appear in inspection documents and by introducing code numbers for each of the designated sections, this European Standard intends to contribute to the elimination of communication difficulties in European trade.
- Standard12 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies requirements for steel lighting columns. It includes materials and conformity control. It applies to post top columns not exceeding 20 m height for post top lanterns and to columns with brackets not exceeding 18 m height for side entry lanterns.
This European Standard specifies performance related to the essential requirements of resistance to horizontal (wind) loads and performance under impact in support of the Essential Requirement No 4 Safety in use measured according to the corresponding test methods included in this European Standard or available in separate European Standards.
It provides for the evaluation of conformity of the products to this European Standard.
- Standard26 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies requirements for steel lighting columns. It includes materials and conformity control. It applies to post top columns not exceeding 20 m height for post top lanterns and to columns with brackets not exceeding 18 m height for side entry lanterns.
This European Standard specifies performance related to the essential requirements of resistance to horizontal (wind) loads and performance under impact in support of the Essential Requirement No 4 Safety in use measured according to the corresponding test methods included in this European Standard or available in separate European Standards.
It provides for the evaluation of conformity of the products to this European Standard.
- Standard26 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard applies to bright steel products in the drawn, turned or ground condition delivered in straight lengths. It does not cover cold rolled products and cut lengths produced from strip or sheet by cutting.
- Standard13 pagesEnglish languagesale 10% offe-Library read for1 day
- Standard13 pagesGerman languagesale 10% offe-Library read for1 day
This European Standard specifies the requirements for the product forms for use in pressure parts of water-tube boilers and for parts welded on to pressure parts:
- plates;
- wrought seamless tubes;
- electrically welded tubes;
- submerged, plasma and TIG arc-welded tubes;
- forgings;
- castings;
- rolled bars;
- welding consumables;
- fasteners;
- seamless composite tubes.
- Standard38 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies requirements for the design, materials, manufacturing and testing of pressure vessels and pressure vessel parts intended for use with a maximum allowable pressure, PS, equal or less than 100 bar and shell wall thicknesses not exceeding 60 mm, which are constructed of ferritic or austenitic spheroidal graphite cast iron. The thickness limitation of the shell does not apply to thickness of flanges, reinforcements, bosses etc.
The allowable grades do not include lamellar graphite cast iron grades for ferritic and austenitic grades, which are explicitly excluded from this European Standard because of low elongation and brittle material behaviour, which requires the use of different safety factors and a different approach.
NOTE 1 Austenitic spheroidal graphite cast iron grades are principally used for high and low temperature applications and for their corrosion resistance properties.
NOTE 2 The allowable grades of spheroidal graphite cast iron are listed in Tables 3 and Tables 4. Service conditions are given in Clause 4.
- Amendment7 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies requirements for the design, materials, manufacturing and testing of pressure vessels and pressure vessel parts intended for use with a maximum allowable pressure, PS, equal or less than 100 bar and shell wall thicknesses not exceeding 60 mm, which are constructed of ferritic or austenitic spheroidal graphite cast iron. The thickness limitation of the shell does not apply to thickness of flanges, reinforcements, bosses etc. The allowable grades do not include lamellar graphite cast iron grades for ferritic and austenitic grades, which are explicitly excluded from this European Standard because of low elongation and brittle material behaviour, which requires the use of different safety factors and a different approach. NOTE 1 Austenitic spheroidal graphite cast iron grades are principally used for high and low temperature applications and for their corrosion resistance properties. NOTE 2 The allowable grades of spheroidal graphite cast iron are listed in Tables 3 and 4. Service conditions are given in Clause 4.
- Amendment18 pagesEnglish languagesale 10% offe-Library read for1 day
- Amendment16 pagesEnglish languagesale 10% offe-Library read for1 day
EN 13445-6 specifies requirements for the design, materials, manufacturing and testing of pressure vessels and pressure vessel parts intended for use with a maximum allowable pressure, PS, equal or less than 100 bar and shell wall thicknesses not exceeding 60 mm, which are constructed of ferritic or austenitic spheroidal graphite cast iron. The thickness limitation of the shell does not apply to thickness of flanges, reinforcements, bosses etc. The allowable grades do not include lamellar graphite cast iron grades for ferritic and austenitic grades, which are explicitly excluded from this European Standard because of low elongation and brittle material behaviour, which requires the use of different safety factors and a different approach.
- Standard55 pagesEnglish languagesale 10% offe-Library read for1 day
The present CEN report establishes a classification between alloy and non alloy steels which are indicated in the existing European Standards as function of the quality classes defined in prEN 10020:1999.
- Standardization document8 pagesEnglish languagesale 10% offe-Library read for1 day
This Technical Report describes the classification, method of sample preparation, certification main rules and certificate content of the EURONORM-CRMs.
It also lists the sample presentation of the corresponding producer's organizations and the distributing sources.
- Technical report11 pagesEnglish languagesale 10% offe-Library read for1 day
- Technical report11 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies through thickness properties and associated test methods for flat products and sections of steel.
This European Standard may be applied as a supplement to all product standards for flat products and sections of killed steels, except stainless steels. It covers products having a thickness between 15 mm and 400 mm inclusive of steels with a specified minimum upper yield strength ReH or proof strength Rp0,2 L 960 MPa ) for which improved through thickness properties are required.
The application of this European Standard to other product thicknesses and other steel types shall be the subject of agreement at the time of the order.
See option 1.
- Standard14 pagesEnglish languagesale 10% offe-Library read for1 day
This part of EN 10277 applies to bright steel bars in the drawn, turned or ground condition, in straight lengths of free-cutting steels. This EN 10277-3 is complemented by EN 10277-1.
- Standard9 pagesEnglish languagesale 10% offe-Library read for1 day
This part of EN 10277 applies to bright steel bars in the drawn, turned or ground condition, in straight lengths of case hardening steels. This EN 10277-4 is complemented by EN 10277-1.
- Standard10 pagesEnglish languagesale 10% offe-Library read for1 day
This part of EN 10277 applies to bright steel bars in the drawn, turned or ground condition, in straight lengths of steels for quenching and tempering. This EN 10277-5 is complemented by EN 10277-1.
- Standard12 pagesEnglish languagesale 10% offe-Library read for1 day
This part of EN 10277 specifies the general technical delivery conditions for bright steel bars in the drawn, turned or ground condition, in straight lengths and of the following steel types: a) steels for general engineering purposes as specified in EN 10277-2; b) free-cutting steels as specified in EN 10277-3; c) case hardening steels as specified in EN 10277-4; d) steels for quenching and tempering as specified in EN 10277-5. It does not cover cold rolled products and cut lengths produced from strip or sheet by cutting. In special cases variations in these technical delivery requirements or additions to them may form the subject of an agreement at the time of enquiry and order (see Annex B). In addition to the specifications of this European Standard, the general technical delivery requirements of EN 10021 are applicable, unless otherwise specified.
- Standard18 pagesEnglish languagesale 10% offe-Library read for1 day
This part of EN 10277 applies to bright steel bars for general engineering purposes in the drawn, turned or ground condition and in straight lengths. This EN 10277-2 is complemented by EN 10277-1.
- Standard9 pagesEnglish languagesale 10% offe-Library read for1 day
ISO 4885:2017 defines important terms used in the heat treatment of ferrous materials.
NOTE The term ferrous materials include products and workpieces of steel and cast iron.
Annex A provides an alphabetical list of terms defined in this document, as well as their equivalents in French, German, Chinese and Japanese.
Table 1 shows the various iron-carbon (Fe-C) phases.
- Standard48 pagesEnglish languagesale 10% offe-Library read for1 day
- Draft53 pagesGerman languagesale 10% offe-Library read for1 day
This International Standard specifies requirements for the identification, location and preparation of samples and test pieces intended for mechanical tests on steel sections, bars, rod, flat products and tubular products as defined in ISO 6929. If agreed in the order this standard may also apply to other metallic products. These samples and test pieces are for use in tests which are carried out in conformity with the methods specified in the product or material standard or, in the absence of this, in the test standard. Where the requirements of the order or product standard differ from those given in this International Standard, then the requirements of the order or product standard apply.
- Standard29 pagesEnglish languagesale 10% offe-Library read for1 day
ISO 377:2013 specifies requirements for the identification, location and preparation of samples and test pieces intended for mechanical tests on steel sections, bars, rod, flat products and tubular products as defined in ISO 6929. If agreed in the order, ISO 377:2013 can also apply to other metallic products. These samples and test pieces are for use in tests that are carried out in conformity with the methods specified in the product or material standard or, in the absence of this, in the standard for the test method.
Where the requirements of the order or product standard differ from those given in ISO 377:2013, then the requirements of the order or product standard apply.
- Standard29 pagesEnglish languagesale 10% offe-Library read for1 day
ISO 4885:2017 defines important terms used in the heat treatment of ferrous materials. NOTE The term ferrous materials include products and workpieces of steel and cast iron. Annex A provides an alphabetical list of terms defined in this document, as well as their equivalents in French, German, Chinese and Japanese. Table 1 shows the various iron-carbon (Fe-C) phases.
- Standard41 pagesEnglish languagesale 15% off
- Standard42 pagesFrench languagesale 15% off
This document specifies the technical delivery conditions for hot and cold formed stainless steel bars for the construction of pressure equipment supplied in accordance with one of the process routes and surface finishes listed in Table 5.
The general technical delivery conditions in EN 10021 also apply.
NOTE Once this European Standard is published in the EU Official Journal (OJEU) under Directive 97/23/EC, presumption of conformity to the Essential Safety Requirements (ESRs) of Directive 97/23/EC is limited to technical data of materials in this European Standard and does not presume adequacy of the material to a specific item of equipment. Consequently, the assessment of the technical data stated in this material standard against the design requirements of this specific item of equipment to verify that the ESRs of Directive 97/23/EC are satisfied, needs to be done.
- Standard35 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies requirements for the design, materials, manufacturing and testing of pressure vessels and pressure vessel parts intended for use with a maximum allowable pressure, PS, equal or less 50 bar and shell wall thicknesses not exceeding 60 mm, that are constructed of spheroidal graphite cast iron.
NOTE The grades of spheroidal graphite cast iron allowed are listed in Tables 5.1-1 and 5.1-2. Service conditions are given in clause 4.
- Standard53 pagesEnglish languagesale 10% offe-Library read for1 day