ASTM B86-04
(Specification)Standard Specification for Zinc and Zinc-Aluminum (ZA) Alloy Foundry and Die Castings
Standard Specification for Zinc and Zinc-Aluminum (ZA) Alloy Foundry and Die Castings
SCOPE
1.1 This specification covers commercial zinc, zinc-aluminum castings and continuous cast bar stock, as designated and specified in . Seven alloy compositions are specified and designated as follows:UNS ASTMCommonTraditionalZ33520AG 40A Alloy 3Zamak 3Z33523AG 40B Alloy 7Zamak 7Z35531AC 41A Alloy 5Zamak 5Z35541AC 43A Alloy 2Zamak 2Z35636ZA-8Z35631ZA-12Z35841ZA-27See , Footnote B
SAE Specification, Nos. 903 and 925 conform to the requirements for alloys AG40A and AC41A, respectively.
1.2 Zinc Alloys Z33520, Z33523, Z35531, and Z35541 are used primarily in the manufacture of pressure die castings. Zinc-Aluminum Alloys Z35636, Z35631, and Z35841 are used in the manufacture of both foundry and pressure die castings. These alloys are also fabricated into continuous cast bar stock used for prototyping and screw machine stock.
1.3 The values stated in inch-pound units are to be regarded as the standard.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Data Sheet for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: B 86 – 04
Standard Specification for
Zinc and Zinc-Aluminum (ZA) Alloy Foundry and Die
1
Castings
ThisstandardisissuedunderthefixeddesignationB 86;thenumberimmediatelyfollowingthedesignationindicatestheyearoforiginal
adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.Asuperscript
epsilon (e) indicates an editorial change since the last revision or reapproval.
2
1. Scope* 2.2 ASTM Standards:
B 240 Specification for Zinc and Zinc-Aluminum (ZA)
1.1 This specification covers commercial zinc, zinc-
Alloys in Ingot Form for Foundry and Die Castings
aluminumcastingsandcontinuouscastbarstock,asdesignated
B 275 Practice for Codification of Certain Nonferrous Met-
and specified in Table 1. Seven alloy compositions are speci-
als and Alloys, Cast and Wrought
fied and designated as follows:
B 557 Test Methods of Tension Testing Wrought and Cast
A
UNS ASTM Common Traditional
Aluminum- and Magnesium-Alloy Products
B
Z33520 AG 40A Alloy 3 Zamak 3
B 899 Terminology Relating to Non-ferrous Metals and
Z33523 AG 40B Alloy 7 Zamak 7
Alloys
B
Z35531 AC 41A Alloy 5 Zamak 5
E 8 Test Methods for Tension Testing of Metallic Materials
Z35541 AC 43A Alloy 2 Zamak 2
Z35636 ZA-8
E 23 Test Methods for Notched Bar Impact Testing of
Z35631 ZA-12
Metallic Materials
Z35841 ZA-27
__________ E 29 Practice for Using Significant Digits in Test Data to
A
Determine Conformance with Specifications
See Table 1, Footnote B
B
SAE Specification, Nos. 903 and 925 conform to the requirements for alloys
E 47 Test Methods for Chemical Analysis of Zinc Die-
3
AG40A and AC41A, respectively.
Casting Alloys
E 88 Practice for Sampling Nonferrous Metals and Alloys
1.2 Zinc Alloys Z33520, Z33523, Z35531, and Z35541 are
in Cast Form for Determination of Chemical Composition
used primarily in the manufacture of pressure die castings.
E 527 Practice for Numbering Metals and Alloys (UNS)
Zinc-AluminumAlloys Z35636, Z35631, and Z35841 are used
E 536 TestMethodsforChemicalAnalysisofZincandZinc
in the manufacture of both foundry and pressure die castings.
Alloys
These alloys are also fabricated into continuous cast bar stock
E 634 Practice for Sampling of Zinc and Zinc Alloys for
used for prototyping and screw machine stock.
Optical Emission Spectrometric Analysis
1.3 The values stated in inch-pound units are to be regarded
2.3 North American Die Casting Association (NADCA):
as the standard.
4
NADCA Product Specification Standards for Die Castings
1.4 This standard does not purport to address all of the
2.4 Federal Standard:
safety concerns, if any, associated with its use. It is the
5
Fed. Std. No. 123 Marking for Shipment (Civil Agencies)
responsibility of the user of this standard to become familiar
2.5 Military Standard:
with all hazards including those identified in the appropriate
MIL-STD-129 Marking for Shipment and Storage (Military
Material Data Sheet for this product/material as provided by
5
Agencies)
the manufacturer, to establish appropriate safety and health
2.6 Military Specification:
practices, and determine the applicability of regulatory limi-
5
MIL-P-116 Methods of Preservation
tations prior to use.
2.7 ISO Standard:
2. Referenced Documents H 5301
2.1 The following documents of the issue in effect on date
of order acceptance form a part of this specification to the
2
extent referenced herein: For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website.
1 3
This specification is under the jurisdiction of ASTM Committee B02 on Withdrawn.
4
Nonferrous Metals and Alloys and is the direct responsibility of Subcommittee Available from North American Die Casting, Assn., 2000 5th Ave., River
B02.04 on Zinc and Cadmium. Grove, IL 60171.
5
Current edition approved Oct. 1, 2004. Published October 2004. Originally Available from Standardization Documents Order Desk, DODSSP, Bldg. 4,
approved in 1931. Last previous edition approved in 2003 as B 86 - 03. Section D, 700 Robbins Ave., Philadelphia, PA 19111-5098.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
B86–04
TABLE 1 Chemical Requirements
Z33520 Z33523 Z35531 Z35541 Z35636 Z35631 Z35841
A,B,C,D A,B,C,D A,B,C,D A,C,,D A,C,E A,C,E A,C,E
(AG40A) (AG40B) (AC41A) (AC43A)
Element
Alloy 3 Alloy 7 Alloy 5 Alloy 2 ZA-8 ZA-12 ZA-27
Zamak 3 Zamak 7 Zamak 5 Zamak 2
Aluminum 3.5-4.3 3.5-4.3 3.5-4.3 3.5-4.3 8.0-8.8 10.5-11.5 25.0-28.0
F F
Magnesium 0.020-0.05 0.005-0.020 0.03-0.08 0.020-0.050 0.015-0.030 0.015-0.030 0.0
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.