ASTM F1807-07ae1
(Specification)Standard Specification for Metal Insert Fittings Utilizing a Copper Crimp Ring for SDR9 Cross-linked Polyethylene (PEX) Tubing
Standard Specification for Metal Insert Fittings Utilizing a Copper Crimp Ring for SDR9 Cross-linked Polyethylene (PEX) Tubing
SCOPE
1.1 This specification covers metal insert fittings and copper crimp rings for use with cross-linked polyethylene (PEX) tubing in 3/8, 1/ 2, 5/8, 3/4, and 1 in. and 1 1/4 nominal diameters that meet the requirements for Specifications F 876 and F 877. These fittings are intended for use in 100 psi (689.5 kPa) cold- and hot-water distribution systems operating at temperatures up to, and including, 180°F (82°C). The requirements for materials, workmanship, dimensions, and markings to be used on the fittings and rings are also included.
1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are mathematical conversions to SI units which are provided for information only and are not considered the standard.
1.3 Compliance with this specification requires that these fittings be tested and certified to Specification F 877.
This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
An American National Standard
e1
Designation: F 1807 – 07a
Standard Specification for
Metal Insert Fittings Utilizing a Copper Crimp Ring for SDR9
1
Cross-linked Polyethylene (PEX) Tubing
This standard is issued under the fixed designation F 1807; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
1
e NOTE—Table 1 and 1.1 were editorially corrected in November 2007.
1. Scope B62 Specification for Composition Bronze or Ounce Metal
Castings
1.1 This specification covers metal insert fittings and copper
B75 Specification for Seamless Copper Tube
crimp rings for use with cross-linked polyethylene (PEX)
B88 Specification for Seamless Copper Water Tube
3 1 5 3 1
tubing in ⁄8 , ⁄2 , ⁄8 , ⁄4 , and 1 in. and 1 ⁄4 nominal diameters
B 140/B 140M Specification for Copper-Zinc-Lead (Red
that meet the requirements for Specifications F 876 and F 877.
Brass or Hardware Bronze) Rod, Bar, and Shapes
These fittings are intended for use in 100 psi (689.5 kPa) cold-
B 283 SpecificationforCopperandCopper-AlloyDieForg-
and hot-water distribution systems operating at temperatures
ings (Hot-Pressed)
up to, and including, 180°F (82°C). The requirements for
B 584 Specification for Copper Alloy Sand Castings for
materials, workmanship, dimensions, and markings to be used
General Applications
on the fittings and rings are also included.
D 1600 Terminology for Abbreviated Terms Relating to
1.2 The values stated in inch-pound units are to be regarded
Plastics
asthestandard.Thevaluesgiveninparenthesesaremathemati-
D 2122 Test Method for Determining Dimensions of Ther-
cal conversions to SI units which are provided for information
moplastic Pipe and Fittings
only and are not considered the standard.
E18 Test Methods for Rockwell Hardness of Metallic
1.3 Compliance with this specification requires that these
Materials
fittings be tested and certified to Specification F 877.
F 412 Terminology Relating to Plastic Piping Systems
1.4 This standard does not purport to address all of the
F 876 Specification for Crosslinked Polyethylene (PEX)
safety concerns, if any, associated with its use. It is the
Tubing
responsibility of the user of this standard to establish appro-
F 877 Specification for Crosslinked Polyethylene (PEX)
priate safety and health practices and determine the applica-
Plastic Hot- and Cold-Water Distribution Systems
bility of regulatory limitations prior to use.
3
2.2 ASME Standards:
2. Referenced Documents B1.20.1 Pipe Threads General Purpose (Inch)
2
B16.18 Cast Copper Alloy Solder Joint Pressure Fittings
2.1 ASTM Standards:
B16.22 Wrought Copper and Copper Alloy Solder Joint
A 269 Specification for Seamless and Welded Austenitic
Pressure Fittings
Stainless Steel Tubing for General Service
4
2.3 Manufacturer’s Standardization Society Standard:
A 276 Specification for Stainless Steel Bars and Shapes
SP-104 Wrought Copper Solder Joint Pressure Fittings
A 312/A 312M Specification for Seamless, Welded, and
5
2.4 NSF International Standard:
Heavily Cold Worked Austenitic Stainless Steel Pipes
Standard No. 14 for Plastic Piping Components and Related
B 16/B 16M Specification for Free-Cutting Brass Rod, Bar
Materials
and Shapes for Use in Screw Machines
Standard No. 61 for Drinking Water System Components-
Health Effects
1
This standard is under the jurisdiction of ASTM Committee F17 on Plastic
Piping Systems and is the direct responsibility of Subcommittee F17.10 on Fittings.
3
Current edition approved Aug. 1, 2007. Published August 2007. Originally Available from American Society of Mechanical Engineers (ASME), ASME
approved in 1997. Last previous edition approved in 2007 as F 1807 – 07. International Headquarters, Three Park Ave., New York, NY 10016-5990.
2 4
For referenced ASTM standards, visit the ASTM website, www.astm.org, or AvailablefromManufacturersStandardizationSocietyoftheValveandFittings
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Industry (MSS), 127 Park St., NE, Vienna, VA 22180-4602.
5
Standards volume information, refer to the standard’s Document Summary page on Available from NSF International, P.O. Box 130140, 789 N. Dixboro Rd.,Ann
the ASTM website. Arbor, MI 48113-0140.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
e1
F 1807 – 07a
6
2.5 EN Standards 6.2 In addition, when a section with a title identical to that
EN 12164 CopperandCopperAlloys-RodforFreeMachin- referenced in 6.1 appears in this specification, it contains
ing Purposes additional requirements that supplement
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
An American National Standard
e1
Designation:F1807–07 Designation: F 1807 – 07a
Standard Specification for
Metal Insert Fittings Utilizing a Copper Crimp Ring for SDR9
1
Cross-linked Polyethylene (PEX) Tubing
This standard is issued under the fixed designation F 1807; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
1
e NOTE—Table 1 and 1.1 were editorially corrected in November 2007.
1. Scope
1.1 This specification covers metal insert fittings and copper crimp rings for use with cross-linked polyethylene (PEX) tubing
3 1 5 3 1 1
in ⁄8 , ⁄2 , ⁄8 , ⁄4 , 1 in., and 1 ⁄4 , and 1 in. and 1 ⁄4 nominal diameters that meet the requirements for Specifications F 876 and
F 877.These fittings are intended for use in 100 psi (689.5 kPa) cold- and hot-water distribution systems operating at temperatures
up to, and including, 180°F (82°C). The requirements for materials, workmanship, dimensions, and markings to be used on the
fittings and rings are also included.
1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are mathematical
conversions to SI units which are provided for information only and are not considered the standard.
1.3 Compliance with this specification requires that these fittings be tested and certified to Specification F 877.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use.
2. Referenced Documents
2
2.1 ASTM Standards:
A 269 Specification for Seamless and Welded Austenitic Stainless Steel Tubing for General Service
A 276 Specification for Stainless Steel Bars and Shapes
A 312/A 312M Specification for Seamless, Welded, and Heavily Cold Worked Austenitic Stainless Steel Pipes
B 16/B 16M Specification for Free-Cutting Brass Rod, Bar and Shapes for Use in Screw Machines
B 62 Specification for Composition Bronze or Ounce Metal Castings
B 75 Specification for Seamless Copper Tube
B 88 Specification for Seamless Copper Water Tube
B 140/B 140M Specification for Copper-Zinc-Lead (Red Brass or Hardware Bronze) Rod, Bar, and Shapes
B 283 Specification for Copper and Copper-Alloy Die Forgings (Hot-Pressed)
B 584 Specification for Copper Alloy Sand Castings for General Applications
D 1600 Terminology for Abbreviated Terms Relating to Plastics
D 2122 Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
E 18 Test Methods for Rockwell Hardness of Metallic Materials
F 412 Terminology Relating to Plastic Piping Systems
F 876 Specification for Crosslinked Polyethylene (PEX) Tubing
F 877 Specification for Crosslinked Polyethylene (PEX) Plastic Hot- and Cold-Water Distribution Systems
3
2.2 ASME Standards:
B1.20.1 Pipe Threads General Purpose (Inch)
B16.18 Cast Copper Alloy Solder Joint Pressure Fittings
B16.22 Wrought Copper and Copper Alloy Solder Joint Pressure Fittings
4
2.3 Manufacturer’s Standardization Society Standard:
SP-104 Wrought Copper Solder Joint Pressure Fittings
1
This standard is under the jurisdiction of ASTM Committee F17 on Plastic Piping Systems and is the direct responsibility of Subcommittee F17.10 on Fittings.
Current edition approved MarchAug. 1, 2007. Published MarchAugust 2007. Originally approved in 1997. Last previous edition approved in 20052007 as F 1807 – 057.
2
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at service@astm.org. ForAnnualBookofASTMStandards
volume information, refer to the standard’s Document Summary page on the ASTM website.
3
Available from American Society of Mechanical Engineers (ASME), ASME International Headquarters, Three Park Ave., New York, NY 10016-5990.
4
Available from Manufacturers Standardization Society of the Valve and Fittings Industry (MSS), 127 Park St., NE, Vienna, VA 22180-4602.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
e1
F 1807 – 07a
5
2.4 NSF International Standard:
Standard No. 14 for Plastic Piping Components and Related Materials
Standard No. 61 for Drinking Water System Components-Health Effect
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.