ASTM D3261-15
(Specification)Standard Specification for Butt Heat Fusion Polyethylene (PE) Plastic Fittings for Polyethylene (PE) Plastic Pipe and Tubing
Standard Specification for Butt Heat Fusion Polyethylene (PE) Plastic Fittings for Polyethylene (PE) Plastic Pipe and Tubing
ABSTRACT
This specification covers polyethylene (PE) butt fusion fittings for use with polyethylene pipe (IPS and ISO) and tubing (CTS). Included are requirements for materials, workmanship, dimensions, marking, sustained pressure, and burst pressure. Pressure strength test shall be performed to meet the requirements prescribed.
SCOPE
1.1 This specification covers polyethylene (PE) butt fusion fittings for use with polyethylene pipe (IPS, DIPS, and ISO) and tubing (CTS). Included are requirements for materials, workmanship, dimensions, marking, sustained pressure, and burst pressure.
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:D3261 −15
Standard Specification for
Butt Heat Fusion Polyethylene (PE) Plastic Fittings for
1
Polyethylene (PE) Plastic Pipe and Tubing
This standard is issued under the fixed designation D3261; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope* 2.4 National Sanitation Foundation Standard:
Standard No. 14 for Plastic Piping Components and Related
1.1 This specification covers polyethylene (PE) butt fusion
4
Materials
fittings for use with polyethylene pipe (IPS, DIPS, and ISO)
5
2.5 Plastic Pipe Institute
and tubing (CTS). Included are requirements for materials,
PPI TR-3 Policies and Procedures for Developing Hydro-
workmanship, dimensions, marking, sustained pressure, and
static Design Basis (HDB), Pressure Design Basis (PDB),
burst pressure.
Strength Design Basis (SDB), and Minimum Required
1.2 The values stated in inch-pound units are to be regarded
Strength (MRS) Ratings for Thermoplastic Piping Mate-
as standard. The values given in parentheses are mathematical
rials or Pipe7
conversions to SI units that are provided for information only
PPI TR-4 HDB/SDB/PDB/MRS Listed Materials, PPI List-
and are not considered standard.
ing of Hydrostatic Design Basis (HDB), Strength Design
Basis(SDB),PressureDesignBasis(PDB),andMinimum
2. Referenced Documents
Required Strength (MRS) Ratings for Thermoplastic Pip-
2
2.1 ASTM Standards:
ing Materials or Pipe
D1598 Test Method for Time-to-Failure of Plastic Pipe
Under Constant Internal Pressure
3. Terminology
D1599 Test Method for Resistance to Short-Time Hydraulic
3.1 Definitions are in accordance with Terminology F412
Pressure of Plastic Pipe, Tubing, and Fittings
and abbreviations are in accordance with Terminology D1600,
D1600 Terminology forAbbreviatedTerms Relating to Plas-
unless otherwise specified.
tics
3.2 dimension ratio (DR) for thermoplastic pipe—the ratio
D2122 Test Method for Determining Dimensions of Ther-
of diameter to wall thickness. For this specification it is
moplastic Pipe and Fittings
calculated by dividing the specified outside diameter by the
D2513 Specification for Polyethylene (PE) Gas Pressure
specified wall thickness of the fitting at its area of fusion. DRs
Pipe, Tubing, and Fittings
are rounded and do not calculate exactly.
D3350 Specification for Polyethylene Plastics Pipe and Fit-
tings Materials
4. Classification
F412 Terminology Relating to Plastic Piping Systems
4.1 General—This specification covers butt fusion fittings
2.2 Federal Standard:
3 intended for use with polyethylene pipe and tubing.
Fed. Std. No. 123 Marking for Shipment (Civil Agencies)
4.1.1 Fittings covered by this specification are normally
2.3 Military Standard:
molded. Fittings may be machined from extruded or molded
3
MIL-STD-129 Marking for Shipment and Storage
stock.
4.1.2 Fittings fabricated by thermal welding are not in-
1 cluded in this specification.
This specification is under the jurisdiction ofASTM Committee F17 on Plastic
Piping Systems and is the direct responsibility of Subcommittee F17.10 on Fittings.
4.1.3 Fittings intended for use in the distribution of natural
Current edition approved Dec. 15, 2015. Published January 2016. Originally
gas or petroleum fuels shall also meet the requirements of
ɛ1
approved in 1973. Last previous edition approved in 2012 as D3261 – 12 . DOI:
Specification D2513.
10.1520/D3261-15.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
4
Standards volume information, refer to the standard’s Document Summary page on Available from NSF International, P.O. Box 130140, 789 N. Dixboro Rd.,Ann
the ASTM website. Arbor, MI 48113-0140, http://www.nsf.org.
3 5
DLA Document Services Building 4/D 700 Robbins Avenue Philadelphia, PA Available from Plastics Pipe Institute (PPI), 105 Decker Court, Suite 825,
19111-5094 http://quicksearch.dla.mil/ Irving, TX 75062, http://www.plasticpipe.org.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
D3261−15
TABLE 1 Specification D3350 Classification of Polyethylene Fittings Materials
Physical Properties Cell Classification and Properties for Polyethylene Pipe Materials
PE2606 PE2706 PE2708 PE3608 PE3708 PE3710 PE4708 PE4710
Density 2 2233344
Melt Index 3 or 4 3 or 4 3 or 4 44444
Flexural modulus $4 $4 $4 $4 $4 $4 $4 $5
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
´1
Designation: D3261 − 12 D3261 − 15
Standard Specification for
Butt Heat Fusion Polyethylene (PE) Plastic Fittings for
1
Polyethylene (PE) Plastic Pipe and Tubing
This standard is issued under the fixed designation D3261; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1
ε NOTE—7.2.2 was editorially corrected in January 2014.
1. Scope*
1.1 This specification covers polyethylene (PE) butt fusion fittings for use with polyethylene pipe (IPS, DIPS, and ISO) and
tubing (CTS). Included are requirements for materials, workmanship, dimensions, marking, sustained pressure, and burst pressure.
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
2. Referenced Documents
2
2.1 ASTM Standards:
D1598 Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure
D1599 Test Method for Resistance to Short-Time Hydraulic Pressure of Plastic Pipe, Tubing, and Fittings
D1600 Terminology for Abbreviated Terms Relating to Plastics
D2122 Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
D2513 Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings
D3350 Specification for Polyethylene Plastics Pipe and Fittings Materials
F412 Terminology Relating to Plastic Piping Systems
2.2 Federal Standard:
3
Fed. Std. No. 123 Marking for Shipment (Civil Agencies)
2.3 Military Standard:
3
MIL-STD-129 Marking for Shipment and Storage
2.4 National Sanitation Foundation Standard:
4
Standard No. 14 for Plastic Piping Components and Related Materials
5
2.5 Plastic Pipe Institute
PPI TR-3 Policies and Procedures for Developing Hydrostatic Design Basis (HDB), Pressure Design Basis (PDB), Strength
Design Basis (SDB), and Minimum Required Strength (MRS) Ratings for Thermoplastic Piping Materials or Pipe7
PPI TR-4 HDB/SDB/PDB/MRS Listed Materials, PPI Listing of Hydrostatic Design Basis (HDB), Strength Design Basis
(SDB), Pressure Design Basis (PDB), and Minimum Required Strength (MRS) Ratings for Thermoplastic Piping Materials
or Pipe
3. Terminology
3.1 Definitions are in accordance with Terminology F412 and abbreviations are in accordance with Terminology D1600, unless
otherwise specified.
1
This specification is under the jurisdiction of ASTM Committee F17 on Plastic Piping Systems and is the direct responsibility of Subcommittee F17.10 on Fittings.
Current edition approved Aug. 1, 2012Dec. 15, 2015. Published December 2012January 2016. Originally approved in 1973. Last previous edition approved in 20102012
ɛ1
as D3261 – 10a.D3261 – 12 . DOI: 10.1520/D3261-12E01.10.1520/D3261-15.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
3
Available from Standardization Documents Order Desk, DODSSP, Bldg. 4, Section D, 700 Robbins Ave., Philadelphia, PA 19111-5098, http://dodssp.daps.dla.mil.DLA
Document Services Building 4/D 700 Robbins Avenue Philadelphia, PA 19111-5094 http://quicksearch.dla.mil/
4
Available from NSF International, P.O. Box 130140, 789 N. Dixboro Rd., Ann Arbor, MI 48113-0140, http://www.nsf.org.
5
Available from Plastics Pipe Institute (PPI), 105 Decker Court, Suite 825, Irving, TX 75062, http://www.plasticpipe.org.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
D3261 − 15
3.2 dimension ratio (DR) for thermoplastic pipe—the ratio of diameter to wall thickness. For this specification it is calculated
by dividing the specified outside diameter by the specified wall thickness of the fitting at its area of fusion. DRs are rounded and
do not calculate exactly.
4. Classification
4.1 General—This specification covers butt fusion fittings intended for use with polyethylene pipe and tubing.
4.1.1 Fittings covered by this specification are normally molded. Fittings may be machined from
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.