ASTM F2206-19
(Specification)Standard Specification for Fabricated Fittings of Butt-Fused Polyethylene (PE)
Standard Specification for Fabricated Fittings of Butt-Fused Polyethylene (PE)
ABSTRACT
This specification deals with fabricated fittings intended for use with outside-diameter controlled polyethylene pipe and tubing. These fittings are manufactured by heat-fusion joining shape-modified polyethylene components prepared from pipe, molded fittings, sheet, or block. Pressure rating of the fabricated-fitting design is beyond the scope of this standard and shall be established by the fitting manufacturer. This specification includes requirements for both room temperature and elevated temperature pressure-tests to demonstrate a reasonable level of performance of the fabricated-fitting design at the pressure rating established by the fitting manufacturer. Materials shall be tested and shall conform to the requirements for materials, design, workmanship, minimum dimensions, marking, test methods, and quality control.
SCOPE
1.1 This specification establishes requirements for fabricated fittings intended for use with outside-diameter controlled polyethylene pipe and tubing. These fittings are manufactured by heat-fusion joining shape-modified polyethylene components prepared from pipe, molded fittings, sheet, billet, or block. Included are requirements for materials, design, workmanship, minimum dimensions, marking, test methods, and quality control.
1.2 Pressure rating of the fabricated-fitting design is beyond the scope of this standard and shall be established by the fitting manufacturer.
1.3 This specification includes requirements for both elevated temperature pressure-tests at the pressure rating established by the fitting manufacturer.
1.4 The pressure-tests requirements are specified by the fittings’ equivalent (E) DR. The EDR specified is the DR of the piping system for which the fabricated fitting is intended to be butt-fused.
1.5 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.
1.6 Units—The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units which are provided for information only and are not considered standard.
1.7 The following safety hazards caveat pertains only to the test methods portion, Section 9, of this specification.. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Relations
Buy Standard
Standards Content (Sample)
This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation: F2206 −19 An American National Standard
Standard Specification for
1
Fabricated Fittings of Butt-Fused Polyethylene (PE)
This standard is issued under the fixed designation F2206; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* ization established in the Decision on Principles for the
Development of International Standards, Guides and Recom-
1.1 This specification establishes requirements for fabri-
mendations issued by the World Trade Organization Technical
cated fittings intended for use with outside-diameter controlled
Barriers to Trade (TBT) Committee.
polyethylene pipe and tubing. These fittings are manufactured
by heat-fusion joining shape-modified polyethylene compo-
2. Referenced Documents
nents prepared from pipe, molded fittings, sheet, billet, or
2
2.1 ASTM Standards:
block. Included are requirements for materials, design,
D1600 Terminology forAbbreviatedTerms Relating to Plas-
workmanship, minimum dimensions, marking, test methods,
tics
and quality control.
D2122 Test Method for Determining Dimensions of Ther-
1.2 Pressure rating of the fabricated-fitting design is beyond
moplastic Pipe and Fittings
the scope of this standard and shall be established by the fitting
D2513 Specification for Polyethylene (PE) Gas Pressure
manufacturer.
Pipe, Tubing, and Fittings
D3035 SpecificationforPolyethylene(PE)PlasticPipe(DR-
1.3 This specification includes requirements for both el-
PR) Based on Controlled Outside Diameter
evated temperature pressure-tests at the pressure rating estab-
D3261 Specification for Butt Heat Fusion Polyethylene (PE)
lished by the fitting manufacturer.
Plastic Fittings for Polyethylene (PE) Plastic Pipe and
1.4 The pressure-tests requirements are specified by the
Tubing
fittings’equivalent (E) DR.The EDR specified is the DR of the
F412 Terminology Relating to Plastic Piping Systems
piping system for which the fabricated fitting is intended to be
F714 Specification for Polyethylene (PE) Plastic Pipe (DR-
butt-fused.
PR) Based on Outside Diameter
1.5 The text of this standard references notes and footnotes
F2619/F2619M SpecificationforHigh-DensityPolyethylene
which provide explanatory material. These notes and footnotes
(PE) Line Pipe
(excluding those in tables and figures) shall not be considered
F2880 Specification For Lap-Joint Type FlangeAdapters for
as requirements of the standard.
Polyethylene Pressure Pipe in Nominal Pipe Sizes 3/4 in.
to 65 in.
1.6 Units—The values stated in inch-pound units are to be
F3034 Specification for Billets made by Winding Molten
regarded as standard. The values given in parentheses are
Extruded Stress-Rated High Density Polyethylene
mathematical conversions to SI units which are provided for
(HDPE)
information only and are not considered standard.
3
2.2 Federal Standards:
1.7 The following safety hazards caveat pertains only to the
Fed. Std. No. 123 Marking for Shipment (Civil Agencies)
test methods portion, Section 9, of this specification. This
OPS Part 192 Title 49, Code of Federal Regulations
standard does not purport to address all of the safety concerns,
3
2.3 Military Standard:
if any, associated with its use. It is the responsibility of the user
MIL-STD-129 Marking for Shipment and Storage
of this standard to establish appropriate safety, health, and
4
2.4 ANSI/NSF Standard:
environmental practices and determine the applicability of
ANSI/NSF 61 for Drinking Water System Components—
regulatory limitations prior to use.
Health Effects
1.8 This international standard was developed in accor-
dance with internationally recognized principles on standard-
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
Standards volume information, refer to the standard’s Document Summary page on
1
This specification is under the jurisdiction ofASTM Committee F17 on Plastic the ASTM website.
3
Piping Systems and is the direct responsibility of Subcommittee F17.10 on Fittings. DLA Document Services Building 4/D 700 Robbins Avenue Philadelphia, PA
Current edition approved Jan. 15, 2019. Published January 2019. Originally 19111-5094 http://quicksearch.dla.mil/
4
approved in 2002. Last previous edition approved in 2014 as F2206 – 14. DOI: Available fromAmerican National Standards Institute (ANSI), 25 W. 43rd St.,
10.1520/F2206-19. 4th Floor, New York, NY 10036, http://www.ansi.org.
*A Summary of Changes sect
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: F2206 − 14 F2206 − 19 An American National Standard
Standard Specification for
1
Fabricated Fittings of Butt-Fused Polyethylene (PE)
This standard is issued under the fixed designation F2206; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope*
1.1 This specification establishes requirements for fabricated fittings intended for use with outside-diameter controlled
polyethylene pipe and tubing. These fittings are manufactured by heat-fusion joining shape-modified polyethylene components
prepared from pipe, molded fittings, sheet, billet, or block. Included are requirements for materials, design, workmanship,
minimum dimensions, marking, test methods, and quality control.
1.2 Pressure rating of the fabricated-fitting design is beyond the scope of this standard and shall be established by the fitting
manufacturer. This specification includes requirements for both elevated temperature pressure-tests and short-term pressurization
tests to demonstrate a reasonable level of performance of the fabricated-fitting design at the pressure rating established by the
fitting manufacturer.
1.3 This specification includes requirements for both elevated temperature pressure-tests at the pressure rating established by
the fitting manufacturer.
1.4 The pressure-tests requirements are specified by the fittings’ equivalent (E) DR. The EDR specified is the DR of the piping
system for which the fabricated fitting is intended to be butt-fused.
1.5 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes
(excluding those in tables and figures) shall not be considered as requirements of the standard.
1.6 Units—The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are
mathematical conversions to SI units which are provided for information only and are not considered standard.
1.7 The following safety hazards caveat pertains only to the test methods portion, Section 9, of this specification.specification.
This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the
user of this standard to establish appropriate safety safety, health, and healthenvironmental practices and determine the
applicability of regulatory limitations prior to use.
1.8 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2
2.1 ASTM Standards:
D1600 Terminology for Abbreviated Terms Relating to Plastics
D2122 Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
D2513 Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings
D3035 Specification for Polyethylene (PE) Plastic Pipe (DR-PR) Based on Controlled Outside Diameter
D3261 Specification for Butt Heat Fusion Polyethylene (PE) Plastic Fittings for Polyethylene (PE) Plastic Pipe and Tubing
F412 Terminology Relating to Plastic Piping Systems
F714 Specification for Polyethylene (PE) Plastic Pipe (DR-PR) Based on Outside Diameter
F2619/F2619M Specification for High-Density Polyethylene (PE) Line Pipe
F2880 Specification For Lap-Joint Type Flange Adapters for Polyethylene Pressure Pipe in Nominal Pipe Sizes 3/4 in. to 65 in.
F3034 Specification for Billets made by Winding Molten Extruded Stress-Rated High Density Polyethylene (HDPE)
1
This specification is under the jurisdiction of ASTM Committee F17 on Plastic Piping Systems and is the direct responsibility of Subcommittee F17.10 on Fittings.
Current edition approved Dec. 1, 2014Jan. 15, 2019. Published January 2015January 2019. Originally approved in 2002. Last previous edition approved in 20112014 as
F2206F2206 – 11.14. DOI: 10.1520/F2206-14.10.1520/F2206-19.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM Inte
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.