ASTM D5823-13
(Test Method)Standard Test Method for Tuft Height of Pile Floor Coverings
Standard Test Method for Tuft Height of Pile Floor Coverings
SIGNIFICANCE AND USE
5.1 This test method is useful in quality and cost control during the manufacture of pile yarn floor covering. Both appearance and performance can be affected by changes in the tuft height.
5.1.1 In case of a dispute arising from differences in reported test results when using this test method for acceptance testing of commercial shipments, the purchaser and the supplier should conduct comparative tests to determine if there is a statistical bias between their laboratories. Competent statistical assistance is recommended for the investigation of bias. As a minimum, the two parties should take a group of test specimens that are as homogeneous as possible and are from a lot of material of the type in question. The test specimens should then be randomly assigned in equal numbers to each laboratory for testing. The average results from the two laboratories should be compared using Student's t-test for unpaired data and an acceptable probability level chosen by the two parties before testing is begun. If a bias is found, either its cause must be found and corrected or the purchaser and the supplier must agree to interpret future test results in view of the known bias.
SCOPE
1.1 This test method covers the determination of tuft height using a grooved specimen holder. It applies to cut-pile and loop-pile floor covering after adhesive backing has been applied to bond the pile yarn to the backing fabric.
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: D5823 − 13
Standard Test Method for
1
Tuft Height of Pile Floor Coverings
This standard is issued under the fixed designation D5823; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope 3.2 For all other terminology related to textiles see Termi-
nology D123.
1.1 This test method covers the determination of tuft height
using a grooved specimen holder. It applies to cut-pile and
4. Summary of Test Method
loop-pile floor covering after adhesive backing has been
4.1 Forcutpilefloorcovering,individualtuftlegspecimens
applied to bond the pile yarn to the backing fabric.
of like character (either cut or loop and of uniform height) are
1.2 The values stated in inch-pound units are to be regarded
cut as closely as possible to the surface of the backing of a pile
as standard. The values given in parentheses are mathematical
floor covering sample and placed, one at a time, in a grooved
conversions to SI units that are provided for information only
specimen holder that maintains the tuft yarn in a straight line
and are not considered standard.
while the length of the tuft leg is measured using a graduated
1.3 This standard does not purport to address all of the
scale and a magnifying glass.
safety concerns, if any, associated with its use. It is the
4.2 For loop pile floor covering, the two tuft legs forming
responsibility of the user of this standard to establish appro-
the loop are each severed from the adjacent binding sites at the
priate safety and health practices and determine the applica-
backing surface to provide a specimen of twice the tuft height
bility of regulatory limitations prior to use.
and the length measured as in 4.1.
2. Referenced Documents
5. Significance and Use
2
2.1 ASTM Standards:
5.1 This test method is useful in quality and cost control
D123Terminology Relating to Textiles
during the manufacture of pile yarn floor covering. Both
D1776Practice for Conditioning and Testing Textiles
appearance and performance can be affected by changes in the
D1909Standard Table of Commercial Moisture Regains for
tuft height.
Textile Fibers
5.1.1 In case of a dispute arising from differences in
D5684Terminology Relating to Pile Floor Coverings
reportedtestresultswhenusingthistestmethodforacceptance
E122PracticeforCalculatingSampleSizetoEstimate,With
testing of commercial shipments, the purchaser and the sup-
Specified Precision, the Average for a Characteristic of a
plier should conduct comparative tests to determine if there is
Lot or Process
a statistical bias between their laboratories. Competent statis-
tical assistance is recommended for the investigation of bias.
3. Terminology
As a minimum, the two parties should take a group of test
3.1 For all terminology related to Pile Floor Coverings, specimens that are as homogeneous as possible and are from a
D13.21, refer to Terminology D5684.
lot of material of the type in question. The test specimens
3.1.1 The following terms are relevant to this standard: should then be randomly assigned in equal numbers to each
finished, finished pile yarn floor covering, floor covering, level
laboratory for testing. The average results from the two
pile, loop pile yarn floor covering, pile, pile yarn floor laboratories should be compared using Student’s t-test for
covering, textile floor covering, tuft height, tuft leg, tufted
unpaireddataandanacceptableprobabilitylevelchosenbythe
fabric. two parties before testing is begun. If a bias is found, either its
cause must be found and corrected or the purchaser and the
suppliermustagreetointerpretfuturetestresultsinviewofthe
1
ThistestmethodisunderthejurisdictionofASTMCommitteeD13onTextiles
known bias.
and is the direct responsibility of Subcommittee D13.21 on Pile Floor Coverings.
Current edition approved July 1, 2013. Published August 2013. Originally
6. Apparatus
approved in 1995. Last previous edition approved in 2005 as D5823–05a. DOI:
10.1520/D5823-13.
6.1 GroovedSpecimenHolder,havingalengthatleast10%
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
longer than the longest tuft element to be measured.
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
6.1.1 Specimen Holder, 4-in. (100-mm) long, has been
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website. found satisfactory for this purpose.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
D5823 − 13
6.1.2 The grooves shall have a V-shaped cross-sec
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: D5823 − 05a D5823 − 13
Standard Test Method for
1
Tuft Height of Pile Floor Coverings
This standard is issued under the fixed designation D5823; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This test method covers the determination of tuft height using a grooved specimen holder. It applies to cut-pile and loop-pile
floor covering after adhesive backing has been applied to bond the pile yarn to the backing fabric.
1.2 The values stated in SIinch-pound units are to be regarded as the standard for all measurements. The inch-pound values are
standard. The values given in parentheses are mathematical conversions to SI units that are provided for information purposes
only.only and are not considered standard.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use.
2. Referenced Documents
2
2.1 ASTM Standards:
D123 Terminology Relating to Textiles
D1776 Practice for Conditioning and Testing Textiles
D1909 Standard Table of Commercial Moisture Regains for Textile Fibers
D5684 Terminology Relating to Pile Floor Coverings
E122 Practice for Calculating Sample Size to Estimate, With Specified Precision, the Average for a Characteristic of a Lot or
Process
3. Terminology
3.1 For all terminology related to Pile Floor Coverings, D13.21, refer to Terminology D5684.
3.1.1 The following terms are relevant to this standard: finished, finished pile yarn floor covering, floor covering, level pile, loop
pile yarn floor covering, pile, pile yarn floor covering, textile floor covering, tuft height, tuft leg, tufted fabric.
3.2 For all other terminology related to textiles see Terminology D123.
4. Summary of Test Method
4.1 For cut pile floor covering, individual tuft leg specimens of like character (either cut or loop and of uniform height) are cut
as closely as possible to the surface of the backing of a pile floor covering sample and placed, one at a time, in a grooved specimen
holder that maintains the tuft yarn in a straight line while the length of the tuft leg is measured using a graduated scale and a
magnifying glass.
4.2 For loop pile floor covering, the two tuft legs forming the loop are each severed from the adjacent binding sites at the
backing surface to provide a specimen of twice the tuft height and the length measured as in 4.1.
5. Significance and Use
5.1 This test method is useful in quality and cost control during the manufacture of pile yarn floor covering. Both appearance
and performance can be affected by changes in the tuft height.
1
This test method is under the jurisdiction of ASTM Committee D13 on Textiles and is the direct responsibility of Subcommittee D13.21 on Pile Floor Coverings.
Current edition approved Sept. 1, 2005July 1, 2013. Published October 2005August 2013. Originally approved in 1995. Last previous edition approved in 2005 as
D5823–05.–05a. DOI: 10.1520/D5823-05A.10.1520/D5823-13.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
D5823 − 13
5.1.1 In case of a dispute arising from differences in reported test results when using this test method for acceptance testing of
commercial shipments, the purchaser and the supplier should conduct comparative tests to determine if there is a statistical bias
between their laboratories. Competent statistical assistance is recommended for the investigation of bias. As a minimum, the two
parties should take a group of test specimens that are as homogeneous as possible and are from a lot of material of the type in
question. The test specimens should then be randomly assigned in equal numbers to each laboratory for testing. The average results
from the two laboratories should be compared using Student’s t-test for unpaired data and an acceptable probability level chosen
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.