ASTM D6263-22

Standard Specification for Extruded Rods and Bars Made From Rigid Poly(Vinyl Chloride) (PVC) and Chlorinated Poly(Vinyl Chloride) (CPVC)

ABSTRACT
This specification covers requirements and test methods for the material, dimensions, and workmanship, and the properties of extruded shapes of rods and bars made from poly(vinyl chloride) (PVC), and chlorinated poly(vinyl chloride) (CPVC). The type of poly(vinyl chloride), and chlorinated poly(vinyl chloride) shape product may be categorized by type, grade, and class depending on resin composition: Types 01 and 02; Classes 0 and 1; Grades 0 and 1. The type, class and grade is further differentiated based on dimensional stability. The following test methods shall be performed: tensile stress at break; elongation at break; tensile modulus; dimensional stability; lengthwise chamber; flexural modulus; izod impact; and degree of fusion of extruded PVC and CPVC by solvent immersion.
SCOPE
1.1 This specification covers requirements and test methods for the material, dimensions, and workmanship, and the properties of extruded shapes of rods and bars made from poly(vinyl chloride) (PVC), and chlorinated poly(vinyl chloride) (CPVC).  
1.2 The properties included in this specification are those required for the compositions covered. Use the classification system given in Section 4 to describe requirements necessary to identify particular characteristics important to specialized applications.  
1.3 This specification allows for the use of regrind and recycled plastics providing products produced from regrind or recycled PVC material can be shown to meet the requirements of this standard with regard to material classification, physical performance, dimensions and workmanship; and the regrind or recycled plastics used have not been subjected to severe environments in post consumer applications (such as chemical service) which could adversely affect the end products performance when subjected to machining or critical applications or both.  
1.4 The values are stated in inch-pound units and are regarded as the standard in all property and dimensional tables. For reference purposes, SI units are also included in Table 1 only.  
1.5 The following safety hazards caveat pertains only to the test method portions section of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
Note 1: There is no known ISO equivalent to this standard.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

General Information

• Status: Historical
• Publication Date: 30-Apr-2022
• ICS: 83.080.20 - Thermoplastic materials
• Technical Committee: D20 - Plastics
• Drafting Committee: D20.15 - Thermoplastic Materials

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:D6263 −22
Standard Specification for
Extruded Rods and Bars Made From Rigid Poly(Vinyl
Chloride) (PVC) and Chlorinated Poly(Vinyl Chloride)
1
(CPVC)
This standard is issued under the fixed designation D6263; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
INTRODUCTION
This specification is intended to be a means of calling out mechanical grade plastic product used in
the fabrication of end items or parts.
1. Scope* does not purport to address all of the safety concerns, if any,
associated with its use. It is the responsibility of the user of this
1.1 This specification covers requirements and test methods
standard to establish appropriate safety, health, and environ-
for the material, dimensions, and workmanship, and the prop-
mental practices and determine the applicability of regulatory
erties of extruded shapes of rods and bars made from poly(vi-
limitations prior to use.
nyl chloride) (PVC), and chlorinated poly(vinyl chloride)
(CPVC).
NOTE 1—There is no known ISO equivalent to this standard.
1.6 This international standard was developed in accor-
1.2 The properties included in this specification are those
dance with internationally recognized principles on standard-
required for the compositions covered. Use the classification
ization established in the Decision on Principles for the
system given in Section 4 to describe requirements necessary
Development of International Standards, Guides and Recom-
to identify particular characteristics important to specialized
mendations issued by the World Trade Organization Technical
applications.
Barriers to Trade (TBT) Committee.
1.3 This specification allows for the use of regrind and
recycled plastics providing products produced from regrind or
2. Referenced Documents
recycled PVC material can be shown to meet the requirements
2
2.1 ASTM Standards:
of this standard with regard to material classification, physical
D256 Test Methods for Determining the Izod Pendulum
performance, dimensions and workmanship; and the regrind or
Impact Resistance of Plastics
recycled plastics used have not been subjected to severe
D618 Practice for Conditioning Plastics for Testing
environments in post consumer applications (such as chemical
D638 Test Method for Tensile Properties of Plastics
service) which could adversely affect the end products perfor-
D790 Test Methods for Flexural Properties of Unreinforced
mance when subjected to machining or critical applications or
and Reinforced Plastics and Electrical Insulating Materi-
both.
als
1.4 The values are stated in inch-pound units and are
D883 Terminology Relating to Plastics
regarded as the standard in all property and dimensional tables.
D1600 Terminology forAbbreviatedTerms Relating to Plas-
For reference purposes, SI units are also included in Table 1
tics
only.
D1784 Classification System and Basis for Specification for
1.5 The following safety hazards caveat pertains only to the
Rigid Poly(Vinyl Chloride) (PVC) Compounds and Chlo-
testmethodportionssectionofthisspecification: This standard
rinated Poly(Vinyl Chloride) (CPVC) Compounds
D3892 Practice for Packaging/Packing of Plastics
1
This specification is under the jurisdiction of ASTM Committee D20 on
Plastics and is the direct responsibility of Subcommittee D20.15 on Thermoplastic
2
Materials (Section D20.20.02). For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM
Current edition approved May 1, 2022. Published May 2022. Originally
Standards volume information, refer to the standard’s Document Summary page on
approved in 1998. Last previous edition approved in 2015 as D6263 - 15. DOI:
the ASTM website.
10.1520/D6263-22.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
D6263−22
2.2 ANSI Standard: ride) materials covered by this specification. The system uses
Z1.4-1993 Sampling Procedures and Tables for Inspection pre-definedcellstorefertospecificaspectsofthisspecification
3
by Attributes as illustrated below:
4.5.1 Examples:
2.3 NSF Standard:
4 4.5.1.1 Example 1—Product made from general purpose
NSF Standard 61
poly(vinyl chloride):
CELL CALLOUT: S-PVC0111
3. Terminology
S-PVC01 = Product made from PVC in accordance with Table
S-PVC-I and Table S-PVC-II
3.1 Definitions:
1 = Unfilled class
3.1.1 For definitions of terms pertaining to plastics used in
1 = General purpose grade product
thi
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: D6263 − 15 D6263 − 22
Standard Specification for
Extruded Rods and Bars Made From Rigid Poly(Vinyl
Chloride) (PVC) and Chlorinated Poly(Vinyl Chloride)
1
(CPVC)
This standard is issued under the fixed designation D6263; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
INTRODUCTION
This specification is intended to be a means of calling out mechanical grade plastic product used in
the fabrication of end items or parts.
1. Scope*
1.1 This specification covers requirements and test methods for the material, dimensions, and workmanship, and the properties of
extruded shapes of rods and bars made from poly(vinyl chloride) (PVC), and chlorinated poly(vinyl chloride) (CPVC).
1.2 The properties included in this specification are those required for the compositions covered. Use the classification system
given in Section 4 to describe requirements necessary to identify particular characteristics important to specialized applications.
1.3 This specification allows for the use of regrind and recycled plastics as defined in Guide providing D7209 providing: products
produced from regrind or recycled PVC material can be shown to meet the requirements of this standard with regard to material
classification, physical performance, dimensions and workmanship; and the regrind or recycled plastics used have not been
subjected to severe environments in post consumer applications (such as chemical service) which could adversely affect the end
products performance when subjected to machining or critical applications or both.
1.4 The values are stated in inch-pound units and are regarded as the standard in all property and dimensional tables. For reference
purposes, SI units are also included in Table 1 only.
1.5 The following safety hazards caveat pertains only to the test method portions section of this specification: This standard
does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this
standard to establish appropriate safety safety, health, and healthenvironmental practices and determine the applicability of
regulatory limitations prior to use.
NOTE 1—There is no known ISO equivalent to this standard.
1.6 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
1
This specification is under the jurisdiction of ASTM Committee D20 on Plastics and is the direct responsibility of Subcommittee D20.15 on Thermoplastic Materials
(Section D20.20.02).
Current edition approved Oct. 1, 2015May 1, 2022. Published October 2015May 2022. Originally approved in 1998. Last previous edition approved in 20112015 as
D6263 - 11.D6263 - 15. DOI: 10.1520/D6263-15.10.1520/D6263-22.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
D6263 − 22
2. Referenced Documents
2
2.1 ASTM Standards:
D256 Test Methods for Determining the Izod Pendulum Impact Resistance of Plastics
D618 Practice for Conditioning Plastics for Testing
D638 Test Method for Tensile Properties of Plastics
D790 Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials
D883 Terminology Relating to Plastics
D1600 Terminology for Abbreviated Terms Relating to Plastics
D1784 Classification System and Basis for Specification for Rigid Poly(Vinyl Chloride) (PVC) Compounds and Chlorinated
Poly(Vinyl Chloride) (CPVC) Compounds
D3892 Practice for Packaging/Packing of Plastics
D7209 Guide for Waste Reduction, Resource Recovery, and Use of Recycled Polymeric Materials and Products (Withdrawn
3
2015)
2.2 ANSI Standard:
3
Z1.4-1993 Sampling Procedures and Tables for Inspection by Attributes
2.3 NSF Standard:
4
NSF Standard 61
3. Terminology
3.1 Definitions:
3.1.1 For definitions of other technical terms pertaining to plastics used in this specification, see standard, refer to Terminology
D883 or Guide . For abbreviations used in this standard, re
...