iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

prEN ISO 10484 rev

(Main)

Widening, crushing and cone proof load tests on nuts

Widening, crushing and cone proof load tests on nuts

2016-11-02:  WI stopped due to cancellation of equivalent ISO WI (notification in dataservice on 2016-10-28).

Mechanische Verbindungselemente - Aufweitversuch an Muttern (ISO/DIS 10484:2014)

Diese Internationale Norm legt das Prüfverfahren zur Beurteilung der Frage fest, ob Muttern mit Oberflächen-fehlern, wie sie in ISO 6152-2 dargestellt sind, angenommen werden können. Sie gilt nicht für Muttern aus Automatenstahl.
Sie gilt für Muttern mit
- Festigkeitsklassen nach ISO 898-2;
- Gewinde-Nenndurchmessern, D, von 5 mm bis 39 mm;
- Produktklassen A und B.

Fixations - Essai d'évasement des écrous (ISO/DIS 10484:2014)

Vezni elementi - Preskus širitve za matice (ISO/DIS 10484:2014)

General Information

Status
Not Published
Publication Date
01-May-2016
ICS
21.060.20 - Nuts
Technical Committee
CEN/TC 185 - Threaded and nonthreaded mechanical fasteners and accessories
Drafting Committee
CEN/TC 185 - Threaded and nonthreaded mechanical fasteners and accessories
Current Stage
4098 - Decision to abandon - Enquiry
Completion Date
16-Nov-2017
Ref Project
oSIST prEN ISO 10484:2014 - Fasteners - Widening test on nuts (ISO/DIS 10484:2014)

Relations

Revises
EN ISO 10484:2004 - Widening test on nuts (ISO 10484:1997)
Effective Date
03-May-2017

Buy Standard

prEN ISO 10484:2014prEN ISO 10484:2014
PreviousNext
Draft
prEN ISO 10484:2014
German language
6 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
oSIST prEN ISO 10484:2014
01-julij-2014
Vezni elementi - Preskus širitve za matice (ISO/DIS 10484:2014)
Fasteners - Widening test on nuts (ISO/DIS 10484:2014)
Mechanische Verbindungselemente - Aufweitversuch an Muttern (ISO/DIS 10484:2014)
Fixations - Essai d'évasement des écrous (ISO/DIS 10484:2014)
Ta slovenski standard je istoveten z: prEN ISO 10484 rev
ICS:
21.060.20 Matice Nuts
oSIST prEN ISO 10484:2014 de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN ISO 10484:2014

---------------------- Page: 2 ----------------------
oSIST prEN ISO 10484:2014

EUROPÄISCHE NORM
ENTWURF
prEN ISO 10484 rev
EUROPEAN STANDARD

NORME EUROPÉENNE

Mai 2014
ICS 21.060.20
Deutsche Fassung
Mechanische Verbindungselemente - Aufweitversuch an Muttern
(ISO/DIS 10484:2014)
Fasteners - Widening test on nuts (ISO/DIS 10484:2014) Fixations - Essai d'évasement des écrous (ISO/DIS
10484:2014)
Dieser Europäische Norm-Entwurf wird den CEN-Mitgliedern zur parallelen Umfrage vorgelegt. Er wurde vom Technischen Komitee
CEN/TC 185 erstellt.

Wenn aus diesem Norm-Entwurf eine Europäische Norm wird, sind die CEN-Mitglieder gehalten, die CEN-Geschäftsordnung zu erfüllen, in
der die Bedingungen festgelegt sind, unter denen dieser Europäischen Norm ohne jede Änderung der Status einer nationalen Norm zu
geben ist.

Dieser Europäische Norm-Entwurf wurde vom CEN in drei offiziellen Fassungen (Deutsch, Englisch, Französisch) erstellt. Eine Fassung in
einer anderen Sprache, die von einem CEN-Mitglied in eigener Verantwortung durch Übersetzung in seine Landessprache gemacht und
dem Management-Zentrum des CEN-CENELEC mitgeteilt worden ist, hat den gleichen Status wie die offiziellen Fassungen.

CEN-Mitglieder sind die nationalen Normungsinstitute von Belgien, Bulgarien, Dänemark, Deutschland, der ehemaligen jugoslawischen
Republik Mazedonien, Estland, Finnland, Frankreich, Griechenland, Irland, Island, Italien, Kroatien, Lettland, Litauen, Luxemburg, Malta,
den Niederlanden, Norwegen, Österreich, Polen, Portugal, Rumänien, Schweden, der Schweiz, der Slowakei, Slowenien, Spanien, der
Tschechischen Republik, der Türkei, Ungarn, dem Vereinigten Königreich und Zypern.

Die Empfänger dieses Norm-Entwurfs werden gebeten, mit ihren Kommentaren jegliche relevante Patentrechte, die sie kennen, mitzuteilen
und unterstützende Dokumentationen zur Verfügung zu stellen.

Warnvermerk : Dieses Schriftstück hat noch nicht den Status einer Europäischen Norm. Es wird zur Prüfung und Stellungnahme
vorgelegt. Es kann sich noch ohne Ankündigung ändern und darf nicht als Europäischen Norm in Bezug genommen werden.


EUROPÄISCHES KOMITEE FÜR NORMUNG
EUROPEAN COMMITTEE FOR STANDARDIZATION

COMITÉ EUROPÉEN DE NORMALISATION

CEN-CENELEC Management-Zentrum: Avenue Marnix 17, B-1000 Brüssel
© 2014 CEN Alle Rechte der Verwertung, gleich in welcher Form und in welchem Ref. Nr. prEN ISO 10484 rev:2014 D
Verfahren, sind weltweit den nationalen Mitgliedern von CEN vorbehalten.

---------------------- Page: 3 ----------------------
oSIST prEN ISO 10484:2014
prEN ISO 10484:2014 (D)
Inhalt
Seite
Vorwort .3
1 Anwendungsbereich .4
2 Normative Verweisungen .4
3 Aufweitversuch .4
3.1 Prinzip .4
3.2 Prüfdorn .4
3.3 Prüfmutter .4
3.4 Versuchsdurchführung .4
4 Beurteilungskriterien .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN ISO 898-2:2022(Main)
Fasteners - Mechanical properties of fasteners made of carbon steel and alloy steel - Part 2: Nuts with specified property classes (ISO 898-2:2022)
SIST EN ISO 898-2:2022

This document specifies the mechanical and physical properties of nuts made of non-alloy steel or alloy steel, when tested at the ambient temperature range of 10 °C to 35 °C.
This document applies to nuts:
—    with ISO metric thread (see ISO 68-1),
—    with diameter/pitch combinations according to ISO 261 and ISO 262,
—    with coarse pitch thread M5 to M39, and fine pitch thread M8×1 to M39×3,
—    with thread tolerances according to ISO 965-1, ISO 965-2 or ISO 965-5,
—    with specified property classes 04, 05, 5, 6, 8, 10 and 12 including proof load,
—    of three different nut styles (see 5.1): regular nuts (style 1), high nuts (style 2) and thin nuts (style 0),
—    with a minimum outside diameter or width across flats s ≥ 1,45D,
—    able to mate with bolts, screws and studs with property classes in accordance with ISO 898-1 (see Annex B), and
—    intended to be used in applications ranging from –50 °C to +150 °C, or up to +300 °C.
WARNING — Nuts conforming to the requirements of this document are tested at the ambient temperature range of 10 °C to 35 °C and are used in applications ranging from –50 °C to +150 °C; however, these nuts are also used outside this range and up to +300 °C for specific applications. It is possible that they do not retain the specified mechanical and physical properties at lower and/or elevated temperatures. Therefore, it is the responsibility of the user to determine the appropriate choices based on the service environment conditions of the assembly (see also 7.1).
For additional specifications applicable to hot dip galvanized nuts, see ISO 10684.
For nuts designed for particular applications, see ISO/TR 16224.
This document does not specify requirements for functional properties such as:
—    prevailing torque properties (see ISO 2320),
—    torque/clamp force properties (see ISO 16047 for test method),
—    weldability, or
—    corrosion resistance.

  • Standard
    41 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    36 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 898-3:2018/A1:2021(Amendment)
Mechanical properties of fasteners made of carbon steel and alloy steel - Part 3: Flat washers with specified property classes - Amendment 1 (ISO 898-3:2018/Amd 1:2020)
SIST EN ISO 898-3:2018/A1:2021
  • Amendment
    7 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    4 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 3506-2:2020(Main)
Fasteners - Mechanical properties of corrosion-resistant stainless steel fasteners - Part 2: Nuts with specified grades and property classes (ISO 3506-2:2020)
SIST EN ISO 3506-2:2020

This document specifies the mechanical and physical properties of nuts, with coarse pitch thread and fine pitch thread, made of corrosion-resistant stainless steels, when tested at the ambient temperature range of 10 °C to 35 °C. It specifies property classes in relation to austenitic, martensitic, ferritic and duplex (austenitic-ferritic) steel grades for nuts.
ISO 3506‑6 provides general rules and additional technical information on suitable stainless steels and their properties.
Nuts conforming to the requirements of this document are evaluated at the ambient temperature specified in paragraph 1. It is possible that they do not retain the specified mechanical and physical properties at elevated and/or lower temperatures.
NOTE 1  Fasteners conforming to the requirements of this document are used without restriction in applications ranging from ?20 °C to +150 °C; however, fasteners conforming to this document are also used for applications outside this range down to ?196 °C and up to +300 °C. For more details, see ISO 3506-6.
Outside the temperature range of ?20 °C to +150 °C, it is the responsibility of the user to determine the appropriate choice for a given application, in consultation with an experienced fastener metallurgist and by taking into account e.g. stainless steel composition, duration of exposure at elevated or low temperature, the effect of the temperature on the fastener mechanical properties and clamped parts, and the corrosive service environment of the bolted joint.
NOTE 2  ISO 3506‑5[1] is developed in order to assist in the selection of appropriate stainless steel grades and property classes intended for use at temperatures up to +800 °C.
This document applies to nuts:
—     with ISO metric thread in accordance with ISO 68‑1,
—     with diameter/pitch combinations in accordance with ISO 261 and ISO 262,
—     with coarse pitch thread M5 to M39, and fine pitch thread M8×1 to M39×3,
—     with thread tolerances in accordance with ISO 965‑1 and ISO 965‑2,
—     with specified property classes, including proof load,
—     with different nut styles: thin nuts, regular nuts and high nuts,
—     with a minimum nut height m ≥ 0,45D,
—     with a minimum outside diameter or width across flats s ≥ 1,45D (see Annex A),
—     of any shape, and
—     able to mate with bolts, screws and studs with property classes in accordance with ISO 3506‑1.
Stainless steel grades and property classes can be used for sizes outside the diameter limits of this document (i.e. for D < 5 mm or D > 39 mm), provided that all applicable chemical, mechanical and physical requirements are met.
This document does not specify requirements for functional properties such as:
—     torque/clamp force properties,
—     prevailing torque properties, or
—     weldability.
[1] Under preparation.

  • Standard
    37 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    37 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 898-3:2018(Main)
Mechanical properties of fasteners made of carbon steel and alloy steel - Part 3: Flat washers with specified property classes (ISO 898-3:2018)
SIST EN ISO 898-3:2018

This document specifies mechanical and physical properties of flat washers, designed to be used in bolted joints in combination with bolts, screws, studs and nuts with a specified property class in accordance with ISO 898‑1 and ISO 898‑2.
NOTE 1    These types of washers can also be used with other fasteners such as screws forming their own mating thread.
Washers that conform to the requirements of this document are evaluated at an ambient temperature range of 10 °C to 35 °C. They might not retain the specified mechanical and physical properties at elevated temperatures and/or lower temperatures.
NOTE 2    Washers conforming to the requirements of this document are used in applications ranging from −50 °C to +150 °C. Users are advised to consult an experienced fastener expert for temperatures outside this range and up to a maximum temperature of +300 °C when determining appropriate choices, or for critical applications.
This document is applicable to the following flat captive and non-captive washers made of carbon steel or alloy steel, with thickness from 0,2 mm to 12 mm:
—          plain washers (with or without knurls, ribs or chamfers);
—          square washers;
—          square hole washers;
—          shaped plates.
It does not specify requirements for the following properties:
—          corrosion resistance;
—          weldability.

  • Standard
    25 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 2320:2015(Main)
Fasteners - Prevailing torque steel nuts - Functional properties (ISO 2320:2015)
SIST EN ISO 2320:2016

ISO 2320:2015 specifies the functional properties for prevailing torque steel nuts when tested at an ambient temperature range of +10 °C to +35 °C. It includes a combined test method to determine the prevailing torque properties and the torque/clamp force properties at the same time.
It applies to prevailing torque all metal type nuts and prevailing torque non-metallic insert type nuts:
-      with triangular ISO thread in accordance with ISO 68‑1;
-      with diameter/pitch combination in accordance with ISO 261 and ISO 262;
-      with coarse pitch thread M5 to M39 or with fine pitch thread M8 × 1 to M39 × 3;
-      with thread tolerances in accordance with ISO 965-2;
-      with mechanical properties in accordance with ISO 898‑2;
Prevailing torque values specified in this standard are based on laboratory test conditions.
NOTE 1       Actual prevailing torques in practical application can vary.
NOTE 2       All metal type nuts conforming to the requirements of this International Standard are used in applications ranging from −50 °C to +150 °C.
NOTE 3       Non-metallic insert type nuts conforming to the requirements of this International Standard are used in applications ranging from −50 °C to +120 °C.
WARNING ? Temperatures outside the ambient temperature range can influence the functional properties (torque/clamp force and prevailing torque properties), see Annex A.

  • Standard
    27 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 14399-3:2015(Main)
High-strength structural bolting assemblies for preloading - Part 3: System HR - Hexagon bolt and nut assemblies
SIST EN 14399-3:2015

This European Standard specifies, together with EN 14399 1 and EN 14399 2, the requirements for assemblies of high-strength structural bolts and nuts of system HR suitable for preloaded joints with large widths across flats, thread sizes M12 to M36 and property classes 8.8/8 or 8.8/10 and 10.9/10.
Bolting assemblies in accordance with this document have been designed to allow preloading of at least 0,7 fub × As  ) according to EN 1993 1 8 (Eurocode 3) and to obtain ductility predominantly by plastic elongation of the bolt. For this purpose the components have the following characteristics:
-   normal nut height (style 1), see EN ISO 4032;
-   thread length of the bolt according to ISO 888.
Bolting assemblies in accordance with this document include washers according to EN 14399 6 or to EN 14399 5 (under the nut only).
NOTE   Attention is drawn to the importance of ensuring that bolting assemblies are correctly used if satisfactory results are to be obtained. For recommendations concerning proper application, reference to EN 1090-2 is made.
General requirements and requirements for suitability for preloading are specified in EN 14399 2.
Clamp lengths and grip lengths for the bolting assemblies are specified in the normative Annex A.

  • Standard
    28 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    28 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 21670:2014(Main)
Fasteners - Hexagon weld nuts with flange (ISO 21670:2014)
SIST EN ISO 21670:2014

ISO 21670:2014 specifies characteristics for hexagon weld nuts with flange, with sizes M5 to M16 (coarse thread) or d = 8 mm to 16 mm (fine pitch thread), of product grade A. Weld nuts conforming to ISO 21670:2014 are suitable for use with bolts of property classes up to 10.9 according to ISO 898‑1.

  • Standard
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 7719:2012/AC:2013(Corrigendum)
Prevailing torque type all-metal hexagon regular nuts - Property classes 5, 8 and 10 - Technical Corrigendum 1 (ISO 7719:2012/Cor 1:2013)
SIST EN ISO 7719:2014/AC:2014

ISO corrigendum.

  • Corrigendum
    4 pages
    French language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 8675:2012(Main)
Hexagon thin nuts chamfered (style 0) with metric fine pitch thread - Product grades A and B (ISO 8675:2012)
SIST EN ISO 8675:2013

ISO 8675:2012 specifies the characteristics of chamfered hexagon thin nuts (style 0), with metric fine pitch thread, with nominal thread diameters from 8 mm up to and including 64 mm, with product grade A for sizes D ≤ 16 mm and product grade B for sizes D > 16 mm.

  • Standard
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 4034:2012(Main)
Hexagon regular nuts (style 1) - Product grade C (ISO 4034:2012)
SIST EN ISO 4034:2013

ISO 4034:2012 specifies the characteristics of hexagon regular nuts (style 1) with threads from M5 up to and including M64 and product grade C.

  • Standard
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day