EN 13383-1:2002

Armourstone - Part 1: Specification

This European Standard specifies the properties of aggregates obtained by processing natural, manufactured or recycled materials and mixtures of these materials for use as armourstone.
It provides for the evaluation of conformity of the products to this European Standard.
NOTE 1   The requirements in this European Standard are based upon experience with armourstone types with an established pattern of use. Care should be taken when considering the use of armourstone from sources with no such pattern of use, e.g., recycled armourstone and armourstone arising from certain industrial by-products. Such armourstone, which should comply with all the requirements of this European Standard, could have other characteristics not included in Mandate M 125 that do not apply to the generality of armourstone types with an established pattern of use and when required, provisions valid at the place of use can be used to assess their suitability.
NOTE 2   Finer aggregates than specified in this European Standard are used in hydraulic structures. For such aggregates European Standards for other end uses of aggregates should be applied.

Wasserbausteine - Teil 1: Anforderungen

Diese Europäische Norm legt die Eigenschaften von Gesteinskörnungen fest, die durch Aufbereitung natürlicher, künstlicher industriell hergestellter oder recycelter rezyklierter Materialien und Mischungen dieser Materialien gewonnen und als Wasserbausteine verwendet werden.
Sie enthält Festlegungen für die Bewertung der Konformität von Produkten nach dieser Europäischen Norm.
ANMERKUNG 1   Die Anforderungen dieser Europäischen Norm basieren auf Erfahrungen mit Wasserbausteinarten, für die ein festgelegtes Anwendungsdie sich in der Anwendung bewährt haben.muster besteht. DieDie Verwendung von Wasserbausteinen aus Bezugsquellen ohne einen derartiges BewährungAnwendungsmuster, wie z. B. von von recyceltenrezyklierten oder in einemin einem industriellen ProzessProzess entstandenen erzeugten Wasserbausteinen, sollte sorgfältig geprüft werden, sollte gründlich erwogen werden. Derartige Wasserbausteine könnten trotz Übereinstimmung mit sämtlichen Anforderungen dieser Europäischen Norm Eigenschaften besitzen, die nicht im Mandat M 125 erfasstenthalten sind und die nicht für die Gesamtheit der Wasserbausteinarten mit einer bewährten Anwendung gelten, die sich bewährt haben mit einem festgelegten Anwendungsmuster gelten.; Ffalls erforderlich, können für die Bewertung Beurteilung ihrer Eignung die am jeweiligen EinsatzVerwendungsort geltenden Vorschriften herangezogen werden.
ANMERKUNG 2   In Wasserbauwerken werden  feinere als die in dieser Europäischen Norm festgelegten Gesteinskörnungen verwendet. Bei derartigen Gesteinskörnungen sollten die für andere Endanwendungen Verwendungszwecke geltenden Europäischen Normen über Gesteinskörnungen angewendet werden.

Enrochements - Partie 1 : Spécifications

La présente Norme européenne spécifie les caractéristiques des granulats naturels, artificiels et recyclés ou les mélanges de ces granulats destinés à être utilisés comme enrochement.
Elle fournit les règles d'évaluation de la conformité des matériaux aux critères de la présente Norme Européenne.
NOTE 1   Les exigences de la présente norme européenne sont basées sur l'expérience acquise avec des types de granulats disposant d'un modèle établi d'utilisation. Il convient de prêter une attention particulière à l'utilisation de granulats provenant de sources ne présentant pas ce type de modèle, par exemple, les granulats recyclés ou les granulats issus de certains produits industriels dérivés. Il est possible que de tels granulats, dont il convient qu'ils soient conformes à toutes les exigences de la présente norme européenne, possèdent d'autres caractéristiques non incluses dans le mandat M 125 et qui ne s'appliquent pas à la totalité des types de granulats dotés d'un modèle établi d'utilisation. Le cas échéant, les dispositions en vigueur sur le lieu d'utilisation peuvent être adoptées pour évaluer leur aptitude à l'emploi.
NOTE 2   Des matériaux plus petits que ceux spécifiés dans la présente norme sont utilisés dans les structures hydrauliques. Dans ce cas, les normes européennes pour d'autres usages doivent être appliquées.

Kamen za obloge pri vodnih zgradbah in drugih gradbenih delih - 1. del: Specifikacija

General Information

• Status: Published
• Publication Date: 07-May-2002
• Withdrawal Date: 31-May-2004
• ICS: 91.100.15 - Mineral materials and products
• Technical Committee: CEN/TC 154 - Aggregates
• Drafting Committee: CEN/TC 154/SC 4 - Hydraulic bound and unbound aggregates
• Current Stage: 9092 - Decision on results of review/2YR ENQ - revise - Review Enquiry
• Start Date: 06-Oct-2006
• Completion Date: 06-Oct-2006
• Directive: 305/2011 - Regulation (eu) No 305/2011 of the European Parliament and of the Council of 9 march 2011 laying down harmonised conditions for the marketing of construction products and repealing council directive 89/106/eec
• Directive: 89/106/EEC - Construction products
• Mandate: M/125 - Mandate to CEN/CENELEC concerning the execution of standardization work for harmonized standards on aggregates
• Ref Project: SIST EN 13383-1:2002 - Armourstone - Part 1: Specification

Relations

• Corrected By: EN 13383-1:2002/AC:2004 - Armourstone - Part 1: Specification
• Effective Date: 08-Jun-2022
• Revised: prEN 13383-1 - Armourstone - Part 1:Characteristics
• Effective Date: 19-Jan-2023
• Revised: FprEN 13383-1 - Armourstone - Part 1: Product standard
• Effective Date: 08-Jun-2022
• Revised: EN 13383-1:2013 - Armourstone - Part 1: Specification
• Effective Date: 22-Dec-2008
• Child: EN 13383-2:2002 - Armourstone - Part 2: Test methods
• Effective Date: 22-Dec-2008

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Armourstone - Part 1: SpecificationKamen za obloge pri vodnih zgradbah in drugih gradbenih delih - 1. del: SpecifikacijaEnrochements - Partie 1 : SpécificationsWasserbausteine - Teil 1: Anforderungen91.100.15Mineralni materiali in izdelkiMineral materials and productsICS:SIST EN 13383-1:2002enTa slovenski standard je istoveten z:EN 13383-1:200201-september-2002SIST EN 13383-1:2002SLOVENSKI
STANDARD
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 13383-1May 2002ICS 91.100.15English versionArmourstone - Part 1: SpecificationEnrochements - Partie 1: SpécificationsWasserbausteine - Teil 1: AnforderungenThis European Standard was approved by CEN on 25 March 2002.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2002 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 13383-1:2002 E

Limits of coarse, light and heavy gradings.19Annex B (informative)
Guidance on block integrity.20Annex C (informative)
Guidance on the resistance of armourstone to freezing and thawing and to saltcrystallization.21Annex D (normative)
Factory production control.24Annex E (informative)
Properties and information which comprise the description of armourstone.30Annex ZA (informative)
Clauses of this European Standard addressing the provisions of EUConstruction Products Directive.31Bibliography.38

construction.prEN 13450Aggregates for railway ballast.According to the CEN/CENELEC Internal Regulations, the national standards organizations of the followingcountries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland,France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Spain,Sweden, Switzerland and the United Kingdom.

ScopeThis European Standard specifies the properties of aggregates obtained by processing natural, manufactured orrecycled materials and mixtures of these materials for use as armourstone.It provides for the evaluation of conformity of the products to this European Standard.NOTE 1The requirements in this European Standard are based upon experience with armourstone types with an establishedpattern of use. Care should be taken when considering the use of armourstone from sources with no such pattern of use, e.g.,recycled armourstone and armourstone arising from certain industrial by-products. Such armourstone, which should comply withall the requirements of this European Standard, could have other characteristics not included in Mandate M 125 that do notapply to the generality of armourstone types with an established pattern of use and when required, provisions valid at the placeof use can be used to assess their suitability.NOTE 2Finer aggregates than specified in this European Standard are used in hydraulic structures. For such aggregatesEuropean Standards for other end uses of aggregates should be applied.2 Normative referencesThis European Standard incorporates by dated or undated reference, provisions from other publications. Thesenormative references are cited at the appropriate places in the text, and the publications are listed hereafter. Fordated references, subsequent amendments to or revisions of any of these publications apply to this EuropeanStandard only when incorporated in it by amendment or revision. For undated references the latest edition of thepublication referred to applies (including amendments).EN 932-3, Tests for general properties of aggregate — Part 3: Procedure and terminology for simplifiedpetrographic description.EN 932-5, Tests for general properties of aggregate — Part 5: Common equipment and calibration.EN 933-3, Tests for geometrical properties of aggregates — Part 3: Determination of particle shape — Flakiness index.EN 1097-1, Tests for mechanical and physical properties of aggregates — Part 1: Determination of the resistanceto wear (micro-Deval).EN 1367-2, Tests for thermal and weathering properties of aggregates — Part 2: Magnesium sulfate test.EN 1744-1:1998, Tests for chemical properties of aggregates — Part 1: Chemical analysis.prEN 1744-3, Tests for chemical properties of aggregates — Part 3: Preparation of eluates by leachingof aggregates.EN 1926:1999, Methods of test for natural stones — Determination of compressive strength.EN 13383-2:2002, Armourstone — Part 2: Test methods.3 Terms and definitionsFor the purposes of this European Standard, the following terms and definitions apply.3.1armourstonecoarse aggregates used in hydraulic structures and other civil engineering works

80 % by mass.c Fragments.4.2.2 Light gradingsThe mass distribution of light gradings shall be determined in accordance with EN 13383-2:2002, clause 6.The mass distribution of a bulk sample consisting of three samples from a stream of material or six samples from astatic batch shall conform to:
...