EN 2591-506:2001

Aerospace series - Elements of electrical and optical connection - Test methods - Part 506: Use of tools

This standard specifies a method of checking the ability of elements of electrical and optical connection to withstand the use of the tools for insertion and extraction of contacts.
It shall be used together with EN 2591-100.

Luft- und Raumfahrt - Elektrische und optische Verbindungselemente - Prüfverfahren - Teil 506: Anwendung der Werkzeuge

Diese Norm legt ein Verfahren zum Nachweis der Widerstandsfähigkeit von elektrischen und optischen Verbin-dungselementen bei Verwendung von Einsetz- und Lösewerkzeugen für Kontakte fest.
Sie ist in Verbindung mit EN 2591-100 anzuwenden.

Série aérospatiale - Organes de connexion électrique et optique - Méthodes d'essais - Partie 506 : Utilisation des outils

La présente norme spécifie une méthode pour vérifier l'aptitude des organes de connexion à résister à l'utilisation des outils d'insertion et d'extraction des contacts électrique et optique.
Elle doit être utilisée conjointement avec EN 2591-100.

Aerospace series - Elements of electrical and optical connection - Test methods - Part 506: Use of tools

General Information

• Status: Published
• Publication Date: 20-Nov-2001
• Withdrawal Date: 30-May-2002
• ICS: 49.060 - Aerospace electric equipment and systems
• Technical Committee: ASD-STAN - Aerospace
• Drafting Committee: ASD-STAN/D 2 - Electrical
• Current Stage: 9093 - Decision to confirm - Review Enquiry
• Completion Date: 01-Jun-2017
• Ref Project: SIST EN 2591-506:2004 - Aerospace series - Elements of electrical and optical connection - Test methods - Part 506: Use of tools

Standards Content (Sample)

SLOVENSKI STANDARD
01-maj-2004
Aerospace series - Elements of electrical and optical connection - Test methods -
Part 506: Use of tools
Aerospace series - Elements of electrical and optical connection - Test methods - Part
506: Use of tools
Luft- und Raumfahrt - Elektrische und optische Verbindungselemente - Prüfverfahren -
Teil 506: Anwendung der Werkzeuge
Série aérospatiale - Organes de connexion électrique et optique - Méthodes d'essais -
Partie 506 : Utilisation des outils
Ta slovenski standard je istoveten z: EN 2591-506:2001
ICS:
49.060 /HWDOVNDLQYHVROMVND Aerospace electric
HOHNWULþQDRSUHPDLQVLVWHPL equipment and systems
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN 2591-506
NORME EUROPÉENNE
EUROPÄISCHE NORM
November 2001
ICS 49.060
English version
Aerospace series - Elements of electrical and optical connection
- Test methods - Part 506: Use of tools
Série aérospatiale - Organes de connexion électrique et Luft- und Raumfahrt - Elektrische und optische
optique - Méthodes d'essais - Partie 506: Utilisation des Verbindungselemente - Prüfverfahren - Teil 506:
outils Anwendung der Werkzeuge
This European Standard was approved by CEN on 4 June 2001.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,
Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2001 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 2591-506:2001 E
worldwide for CEN national Members.

Foreword
This European Standard has been prepared by the European Association of Aerospace Manufacturers
(AECMA).
After inquiries and votes carried out in accordance with the rules of this Association, this Standard has
received the approval of the National Associations and the Official Services of the member countries of
AECMA, prior to its presentation to CEN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by May 2002, and conflicting national standards shall be withdrawn at
the latest by May 2002.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark,
Finland, France, Ge
...