EN 13445-8:2014
(Main)Unfired pressure vessels - Part 8: Additional requirements for pressure vessels of aluminium and aluminium alloys
Unfired pressure vessels - Part 8: Additional requirements for pressure vessels of aluminium and aluminium alloys
This European Standard specifies requirements for unfired pressure vessels and their parts made of aluminium and aluminium alloys in addition to the general requirements for unfired pressure vessels under EN 13445:2014 Parts 1 to 5. This European Standard specifies unfired pressure vessels for loads up to 500 full cycles.
NOTE Cast materials are not included in this version. Details regarding cast materials will be subject to an amendment to or a revision of this European Standard.
Unbefeuerte Druckbehälter - Teil 8: Zusätzliche Anforderungen an Druckbehälter aus Aluminium und Aluminiumlegierungen
Dieser Teil 8 der Europäischen Norm legt zusätzlich zu den allgemeinen Anforderungen an unbefeuerte Druckbe-hälter nach EN 13445:2014, Teile 1 bis 5, Anforderungen an aus Aluminium und Aluminiumlegierungen hergestellte unbefeuerte Druckbehälter und deren Bauteile fest. Dieser Teil der Europäischen Norm gilt für unbefeuerte Druckbehälter für Druckbelastungen bis zu 500 vollen Lastzyklen.
ANMERKUNG Gusswerkstoffe sind in der vorliegenden Fassung nicht enthalten. Angaben zu Gusswerkstoffen werden in einer Ergänzung bzw. Überarbeitung dieser Norm aufgenommen.
Récipients sous pression non soumis à la flamme - Partie 8 : exigences complémentaires pour les récipients sous pression en aluminium et alliages d'aluminium
La présente Norme européenne spécifie les exigences relatives aux récipients sous pression non soumis à la flamme et à leurs composants en aluminium et alliages d’aluminium, en complément des exigences générales énoncées dans les parties 1 à 5 de l’EN 13445:2014. La présente Norme européenne concerne les récipients sous pression non soumis à la flamme pouvant aller jusqu’à 500 cycles complets de chargement.
NOTE Les matériaux moulés ne sont pas inclus pour l’instant. Des détails relatifs aux matériaux moulés feront l’objet d’un amendement ou à une révision de la présente Norme européenne.
Neogrevane tlačne posode - 8. del: Dodatne zahteve za tlačne posode iz aluminija in aluminijevih zlitin
Standard EN 13445-8 določa zahteve za neogrevane tlačne posode in njihove dele, izdelane iz aluminija ter aluminijevih zlitin, poleg splošnih zahtev za neogrevane tlačne posode iz 1. do 5. dela standarda EN 13445:2014. Ta evropski standard določa neogrevane tlačne posode za obremenitve do vključno 500 polnih ciklov.
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Unbefeuerte Druckbehälter - Teil 8: Zusätzliche Anforderungen an Druckbehälter aus Aluminium und AluminiumlegierungenRécipients sous pression non soumis à la flamme - Partie 8 : exigences complémentaires pour les récipients sous pression en aluminium et alliages d'aluminiumUnfired pressure vessels - Part 8: Additional requirements for pressure vessels of aluminium and aluminium alloys77.150.10Aluminijski izdelkiAluminium products23.020.30MHNOHQNHPressure vessels, gas cylindersICS:Ta slovenski standard je istoveten z:EN 13445-8:2014SIST EN 13445-8:2014en,fr,de01-november-2014SIST EN 13445-8:2014SLOVENSKI
STANDARDSIST EN 13445-8:20091DGRPHãþD
SIST EN 13445-8:2014
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 13445-8
September 2014 ICS
Supersedes EN 13445-8:2009English Version
Unfired pressure vessels - Part 8: Additional requirements for pressure vessels of aluminium and aluminium alloys
Récipients sous pression non soumis à la flamme - Partie 8: Exigences complémentaires pour les récipients sous pression en aluminium et alliages d'aluminium
Unbefeuerte Druckbehälter - Teil 8: Zusätzliche Anforderungen an Druckbehälter aus Aluminium und Aluminiumlegierungen This European Standard was approved by CEN on 19 August 2014.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2014 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 13445-8:2014 ESIST EN 13445-8:2014
EN 13445-8:2014 (E) Issue 1 (2014-09) 2 Contents Page Foreword .4 1 Scope .6 2 Normative references .6 3 Terms, definitions, symbols and units .7 4 General requirements .7 5 Materials .7 5.1 General .7 5.2 Elongation after fracture .7 5.3 Prevention of brittle fracture .7 5.4 Lamellar tearing .8 5.5 Chemical composition .8 5.6 Material grouping system .8 6 Design .9 6.1 General .9 6.2 Design temperature and propert
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.