prEN 15876-1

Electronic fee collection - Conformity evaluation of on-board and roadside equipment to EN 15509 - Part 1: Test suite structure and test purposes

It defines the test suite structure and the test purposes for conformity evaluation of on-board and roadside equipment designed for compliance with the requirements set up in EN 15509.

Elektronische Gebührenerhebung - Konformitätsprüfung von Fahrzeuggeräten und straßenseitigen Einrichtungen nach EN 15509 - Teil 1: Struktur und Zweck des Prüfprogramms

Perception de télépéage - Evaluation de conformité de l'équipement embarqué et de l'équipement au sol à la EN 15509 - Partie 1 : Structure des suites de tests et intention des tests

Elektronsko pobiranje pristojbin - Vrednotenje skladnosti opreme v vozilu in v obcestni napravi s standardom EN 15509 - 1. del: Zgradba preskuševalnega niza in namen preskušanja

General Information

• Status: Not Published
• ICS: 35.240.60 - IT applications in transport
• Technical Committee: CEN/TC 278 - Road transport and traffic telematics
• Drafting Committee: CEN/TC 278/WG 1 - Electronic fee collection and access control (EFC)
• Current Stage: 4599 - Dispatch of FV draft to CMC - Finalization for Vote
• Due Date: 14-Oct-2022
• Completion Date: 14-Oct-2022
• Mandate: M/338 - Standardisation mandate to CEN, CENELEC and ETSI in support of interoperabilty of electonic road toll systems in the community
• Ref Project: oSIST prEN 15876-1:2022 - Electronic fee collection - Conformity evaluation of on-board and roadside equipment to EN 15509 - Part 1: Test suite structure and test purposes

RELATIONS

• Revised: EN 15876-1:2016 - Electronic fee collection - Evaluation of on-board and roadside equipment for conformity to EN 15509 - Part 1: Test suite structure and test purposes
• Effective Date: 22-Dec-2021

Standards Content (sample)

SLOVENSKI STANDARD
oSIST prEN 15876-1:2022
01-september-2022
Elektronsko pobiranje pristojbin - Vrednotenje skladnosti opreme v vozilu in v
obcestni napravi s standardom EN 15509 - 1. del: Zgradba preskuševalnega niza in
namen preskušanja

Electronic fee collection - Conformity evaluation of on-board and roadside equipment to

EN 15509 - Part 1: Test suite structure and test purposes
Elektronische Gebührenerhebung - Konformitätsprüfung von Fahrzeuggeräten und
straßenseitigen Einrichtungen nach EN 15509 - Teil 1: Struktur und Zweck des
Prüfprogramms

Perception de télépéage - Evaluation de conformité de l'équipement embarqué et de

l'équipement au sol à la EN 15509 - Partie 1 : Structure des suites de tests et intention

des tests
Ta slovenski standard je istoveten z: prEN 15876-1
ICS:
03.220.20 Cestni transport Road transport
35.240.60 Uporabniške rešitve IT v IT applications in transport
prometu
43.040.15 Avtomobilska informatika. Car informatics. On board
Vgrajeni računalniški sistemi computer systems
oSIST prEN 15876-1:2022 en,fr,de

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN 15876-1:2022
---------------------- Page: 2 ----------------------
oSIST prEN 15876-1:2022
DRAFT
EUROPEAN STANDARD
prEN 15876-1
NORME EUROPÉENNE
EUROPÄISCHE NORM
June 2022
ICS 35.240.60 Will supersede EN 15876-1:2016
English Version
Electronic fee collection - Conformity evaluation of on-
board and roadside equipment to EN 15509 - Part 1: Test
suite structure and test purposes

Perception de télépéage ¿ Evaluation de conformité de Elektronische Gebührenerhebung -

l'équipement embarqué et de l'équipement au sol à la Konformitätsprüfung von Fahrzeugsgeräten und

EN 15509 ¿ Partie 1 : Structure des suites de tests et straßenseitigen Einrichtungen mit der EN 15509 - Teil

intention des tests 1: Prüfreihenstruktur und Prüfzweck

This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee

CEN/TC 278.

If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations

which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other

language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC

Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,

Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,

Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and

United Kingdom.

Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are

aware and to provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without

notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels

© 2022 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 15876-1:2022 E

worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
oSIST prEN 15876-1:2022
prEN 15876-1:2022 (E)
Contents Page

European foreword ....................................................................................................................................................... 3

Introduction .................................................................................................................................................................... 4

1 Scope .................................................................................................................................................................... 5

2 Normative references .................................................................................................................................... 5

3 Terms and definitions ................................................................................................................................... 5

4 Abbreviations ................................................................................................................................................... 7

5 Conformance ..................................................................................................................................................... 8

6 Test Suite Structure ........................................................................................................................................ 8

Annex A (normative) Test purposes for on-board equipment ................................................................. 13

Annex B (normative) Test purposes for roadside equipment .................................................................. 83

Annex C (normative) PCTR proforma for on-board equipment ............................................................. 123

Annex D (normative) PCTR proforma for roadside equipment ............................................................. 138

Bibliography ............................................................................................................................................................... 147

---------------------- Page: 4 ----------------------
oSIST prEN 15876-1:2022
prEN 15876-1:2022 (E)
European foreword

This document (prEN 15876-1:2022) has been prepared by Technical Committee CEN/TC 278,

Intelligent transport systems, the secretariat of which is held by NEN.
This document is currently submitted to the CEN Enquiry.

This document has been prepared under a mandate given to CEN by the European Commission and the

European Free Trade Association.
This document will supersede EN 15876-1:2016.

This edition of EN 15876-1 incorporates the following main modifications compared with the previous

version:

— amendments to reflect changes to the underlying requirements standards, in particular the updated

data definitions in EN 15509;

— amendments to reflect changes in EN ISO 14907-2, specifically updated references following its

amended structure,

— updated terms to reflect the harmonized terms between electronic fee collection standards in

ISO/TS 17573-2.
---------------------- Page: 5 ----------------------
oSIST prEN 15876-1:2022
prEN 15876-1:2022 (E)
Introduction

CEN/TC 278 has produced a set of standards that support interoperable DSRC-EFC-systems e.g.

prEN ISO/DIS 14906:2022 (a “toolbox” for defining EFC-application transaction) and EN ISO 14907-2

(EFC application interface conformance tests for on-board units). However, these standards are only of

an enabling nature and do not ensure technical interoperability. Therefore EN 15509, Electronic fee

collection ― Interoperability application profile for DSRC was developed to support technical

interoperability between EFC-systems.

This document defines the test suite structure and the test purposes for conformity evaluation of on-

board and roadside equipment designed for compliance with the requirements of EN 15509. A test

standard for evaluation of conformity of on-board and roadside equipment is a necessary element for

coherent, practical and effective appraisal of products' compliance to EN 15509.
This document forms Part 1 of a two-part standard:

— EN 15876-1, Electronic fee collection ― Evaluation of on-board and roadside equipment for conformity

to EN 15509 ― Part 1: Test suite structure and test purposes

— EN 15876-2, Electronic fee collection ― Evaluation of on-board and roadside equipment for conformity

to EN 15509 ― Part 2: Abstract test suites

Together, the two parts of EN 15876 provide the necessary foundation for verification of the

implementation of the interoperability requirements as stated in EN 15509:
— industry is provided with an easy-to-use toolbox for product assessment;

— operators can easily assess conformity to EN 15509 and reference to the standard in tendering

processes;

— authorities and joint undertakings may reference to the test standard when stating interoperability

requirements;

— certification organisations are given an effective tool for certification of products.

---------------------- Page: 6 ----------------------
oSIST prEN 15876-1:2022
prEN 15876-1:2022 (E)
1 Scope

This document specifies the test suite structure (TSS) and test purposes (TPs) for evaluation of on-board

equipment (OBE) and roadside equipment (RSE) to EN 15509.
Normative Annex A presents the test purposes for the OBE.
Normative Annex B presents the test purposes for the RSE.

Normative Annex C provides the protocol conformance test report (PCTR) proforma for OBE.

Normative Annex D provides the PCTR proforma for RSE.
2 Normative references

The following documents are referred to in the text in such a way that some or all of their content

constitutes requirements of this document. For dated references, only the edition cited applies. For

undated references, the latest edition of the referenced document (including any amendments) applies.

FprEN 15509:2022, Electronic fee collection — Interoperability application profile for DSRC

EN ISO 3166-1, Codes for the representation of names of countries and their subdivisions - Part 1: Country

code (ISO 3166-1)

EN ISO 14816, Road transport and traffic telematics - Automatic vehicle and equipment identification -

Numbering and data structure (ISO 14816)

prEN ISO/DIS 14906:2022, Electronic fee collection — Application interface definition for dedicated short-

range communication

EN ISO 14907-2:2021, Electronic fee collection - Test procedures for user and fixed equipment - Part 2:

Conformance test for the on-board unit application interface (ISO 14907-2:2021)
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
3.1
attribute

addressable package of data consisting of a single data element or structured sequences of data elements

[SOURCE: ISO/TS 17573-2:2020, 3.13]
3.2
authenticator
data, possibly encrypted, that is used for authentication
[SOURCE: ISO/TS 17573-2:2020, 3.16]
3.3
data group
class of closely related attributes
[SOURCE: ISO/TS 17573-2:2020, 3.55]
---------------------- Page: 7 ----------------------
oSIST prEN 15876-1:2022
prEN 15876-1:2022 (E)
3.4
Element
EFC Element
coherent set of data and functionality

Note 1 to entry: The functionality includes, where applicable, the security-related functions and the associated

security keys.

Note 2 to entry: EFC Elements are created by the applications and addressed using Element identifiers.

Note 3 to entry: In a given on-board equipment (OBE) (3.9), the EID is used to address a toll context, identified by

the EFC-ContextMark, in which attributes (3.1) can be addressed unambiguously by AttributeIDs inside an EFC

Element of the OBE
[SOURCE: ISO/TS 17573-2:2020, 3.71]
3.5
implementation conformance statement
ICS

statement of capabilities and options that have been implemented that defines to what extent the

implementation is compliant with a given specification
[SOURCE: ISO/TS 17573-2:2020, 3.90]
3.6
implementation conformance statement proforma

document, in the form of a questionnaire, which when completed for an implementation or system

becomes an implementation conformance statement (3.5)
[SOURCE: ISO/TS 17573-2:2020, 3.91]
3.7
implementation extra information for testing
IXIT

statement containing all of the information related to the implementation under test (IUT) and its

corresponding system under test (SUT) which will enable the testing laboratory to run an appropriate

test suite against that IUT
[SOURCE: ISO/TS 17573-2:2020, 3.92]
3.8
implementation extra information for testing proforma

document, in the form of a questionnaire, which when completed for an IUT becomes an implementation

extra information for testing (3.7)
[SOURCE: ISO/TS 17573-2:2020, 3.93]
3.9
on-board equipment
OBE

all required equipment on-board a vehicle for performing required electronic fee collection functions and

communication services
[SOURCE: ISO/TS 17573-2:2020, 3.126]
---------------------- Page: 8 ----------------------
oSIST prEN 15876-1:2022
prEN 15876-1:2022 (E)
3.10
on-board unit
OBU

electronic unit on-board a vehicle for performing specific electronic fee collection functions and for

communication with external systems

Note 1 to entry: OBE and OBU have been used as terms with the same or similar meaning in the standardization of

DSRC and DSRC-based EFC within CEN and ETSI. Previously developed relevant standards used the term OBU with

the meaning OBE as defined in this document. When referring to relevant tests in other documents, this document

uses the terms of the referenced source, which explains why the term OBU is often used in the Annexes.

[SOURCE: ISO/TS 17573-2:2020, 3.127]
3.11
roadside equipment
RSE
fixed or movable electronic fee collection equipment located along the road

Note 1 to entry: RSE and RSU have been used as terms with the same or similar meaning in the standardization of

DSRC and DSRC-based EFC within CEN and ETSI. Previously developed relevant standards used the term RSU with

the meaning RSE as defined in this document. When referring to relevant tests in other documents, this document

uses the terms of the referenced source, which explains why the term RSU is often used in the Annexes

[SOURCE: ISO/TS 17573-2:2020, 3.161]
3.12
tester

combination of equipment, humans and processes able to perform specified conformance tests

[SOURCE: ISO/TS 17573-2:2020, 3.188]
3.13
transaction

whole of the exchange of information between two physically separated communication facilities

[SOURCE: ISO/TS 17573-2:2020, 3.211]
4 Abbreviations

For the purposes of this document, the following abbreviations apply throughout the document unless

otherwise specified.
APDU application protocol data Unit
AP application process
ASN.1 abstract syntax notation one (ISO/IEC 8824-1)
ATS abstract test suite
BI behaviour invalid (i.e. invalid behaviour tests)
BST beacon service table
BV behaviour valid (i.e. Valid Behaviour tests)
DSRC dedicated short-range communication
EFC electronic fee collection
---------------------- Page: 9 ----------------------
oSIST prEN 15876-1:2022
prEN 15876-1:2022 (E)
ICS implementation conformance statement
IUT implementation under test
LLC logical link control
LPDU LLC protocol data unit
MAC medium access control
OBE on-board equipment
OBU on-board unit
PCTR protocol conformance test report
PDU protocol data unit
PICS protocol implementation conformance statement
PIXIT protocol implementation extra information for testing
SCTR system conformance test report
TP test purposes
TSS test suite structure
VST vehicle service table
5 Conformance

The supplier of the OBE and RSE, respectively, is responsible for providing a conformance test report.

The supplier of the OBE shall complete the protocol conformance test report (PCTR) for the OBE as

defined in Annex C.

The supplier of the RSE shall complete the PCTR for the RSE as defined in Annex D.

6 Test Suite Structure
6.1 Structure

The table below shows the test suite structure (TSS) including its subgroups defined for the conformance

testing.
Table 1 — Test Suite Structure
Group Type of IUT Behaviour
Physical layer OBE Valid behaviour
Invalid behaviour
RSE Valid behaviour
Invalid behaviour
DLC MAC sublayer OBE Valid behaviour
Invalid behaviour
RSE Valid behaviour
Invalid behaviour
---------------------- Page: 10 ----------------------
oSIST prEN 15876-1:2022
prEN 15876-1:2022 (E)
Group Type of IUT Behaviour
DLC LLC sublayer OBE Valid behaviour
Invalid behaviour
RSE Valid behaviour
Invalid behaviour
Application layer – OBE Valid behaviour
Functions
Invalid behaviour
RSE Valid behaviour
Invalid behaviour
Application Layer – Data OBE Valid behaviour
Invalid behaviour
RSE Valid behaviour
Invalid behaviour
Application Layer – Security OBE Valid behaviour
Level 0
Invalid behaviour
RSE Valid behaviour
Invalid behaviour
Application Layer – Security OBE Valid behaviour
Level 1
Invalid behaviour
RSE Valid behaviour
Invalid behaviour
Application Layer OBE Valid behaviour
– Transactions
Invalid behaviour
RSE Valid behaviour
Invalid behaviour

Physical layer tests are to be performed in a radio wave lab. They will not form part of the abstract test

suite (ATS).
6.2 Reference to Conformance Specifications

Conformance to a profile standard implies conformance to the related base standards; hence, a number

of test cases for the profile standard are exactly the same as the conformance test cases for the related

base standards. Other test cases are derived from the base standards conformance test cases, by applying

some restrictions or choices in e.g. the parameters values, according to what is stated in the profile

standard. Finally, specific conformance test cases for the profile standard are identified for statements

contained in the profile standard, which have no equivalence in the base standards. These latter cases

cover for example the security algorithms and functions that are described in the profile standard. This

document takes into account already defined test purposes for conformance to the base standards by

referencing them, so that:

a) For test purposes that are identical to those defined in the base standards conformance test cases

(see e.g. ETSI/TS 102 486-1-2 or ETSI/TS 102 486-2-2) a direct reference is reported. For reader's

---------------------- Page: 11 ----------------------
oSIST prEN 15876-1:2022
prEN 15876-1:2022 (E)

convenience, the title or a verbal description of the referenced test purpose is given, together with

the reference.

b) For test purposes that are derived from those defined in the base standards conformance test cases,

a direct reference is reported, plus an indication on how the referred test purpose has to be modified

for the profile conformance testing.

c) For test purposes that are specific to the standard profile, a complete description is given.

An indication on whether a test purpose is identical, derived, or specific is given in each test purpose.

6.3 Test Purposes
6.3.1 TP Definition Conventions
The TPs are defined following the rules shown in Table 2 below.
Table 2 — TP Definition Rules
TP ID according to the TP Title
naming conventions
Reference
TP origin
Initial condition
Stimulus and expected behaviour
The TP ID is a unique identifier. It shall be specified according to the TP
TP ID
naming conventions defined in the sub-clause below.
Title Short description of Test Purpose objective.

Reference The reference should contain the references of the subject to be validated

by the actual TP (specification reference, clause, and paragraph).

TP origin Indicates if the TP is identical to a TP defined in another test standard,

derived from a TP defined in another test standard, or specific for this
profile standard.

Initial condition The condition defines in which initial state the IUT has to be to apply the

actual TP.

Stimulus and Definition of the events the tester performs, and the events that are

expected behaviour expected from the IUT to conform to the base specification.

Note that the reference field normally points to the clause of the base standard EN 15509. As the same

standard contains the Protocol Implementation Conformance Statement proforma, where appropriate a

reference to the relevant table of the PICS is given either in this field or in the text introducing the group

of Test Purposes.
---------------------- Page: 12 ----------------------
oSIST prEN 15876-1:2022
prEN 15876-1:2022 (E)
6.3.2 TP Naming Conventions

Each TP is given a unique identification. This unique identification is built up to contain the following

string of information:
TP///-
TP : to indicate that it is a Test Purpose;

: which group among those defined in Table 1 — Test Suite Structure does the TP apply

to;
: type of IUT (i.e. OBE or RSE);

X : type of testing (i.e. Valid Behaviour tests – BV, or Invalid Behaviour tests – BI);

: sequential TP number (01–99).

The naming conventions are as described in Table 3 — TP Naming Conventions below.

Table 3 — TP Naming Conventions
Identifier TP///<
: x>-
PHY Physical layer
MAC MAC sublayer
LLC LLC sublayer
AP-0BAS Application layer – I Kernel support Security level 0
AP-0FUN Application layer – T Kernel support Security level 0
AP-0DAT Application layer – Data attributes support Security Level 0
AP-0SEC Application layer – Security Level 0 support
AP-0TRA Application layer – Transaction support Security level 0
AP-1BAS Application layer – I Kernel support Security level 1
AP-1FUN Application layer – T Kernel support Security level 1
AP-1DAT Application layer – Data attributes support Security Level 1
AP-1SEC Application layer – Security Level 1 support
AP-1TRA Application layer – Transaction support Security level 1
AP-0BAS Application layer – Initialisation phase support Security
level 0
AP-0GET Application layer - GET-rq PDU test purposes, security level
AP-0SET Application layer - SET-rq PDU test purposes, security level
AP-0STA Application layer - GET-STAMPED-rq PDU test purposes,
security level 0
AP- Application layer - SET-MMI-rq PDU test purposes security
0MMI level 0
AP-0ECH Application layer - ECHO-rq PDU test purposes, security
level 0
---------------------- Page: 13 ----------------------
oSIST prEN 15876-1:2022
prEN 15876-1:2022 (E)
Identifier TP///<
: x>-
AP-0REL Application layer - EVENT-REPORT-rq PDU test purposes,
security level 0
AP-1BAS Application layer - initialization phase test purposes,
security level 1
AP-1GET Application layer - GET-rq PDU test purposes, security level
AP-1SET Application layer - SET-rq PDU test purposes, security level
AP-1STA Application layer - GET-STAMPED-rq PDU test purposes,
security level 1
AP- Application layer - SET-MMI-rq PDU test purposes security
1MMI level 1
AP-1ECH Application layer - ECHO-rq PDU test purposes, security
level 1
= type of IUT OBE On-board equipment
RSE Roadside equipment
x = Type of testing BV Valid Behaviour Tests
BI Invalid Behaviour Tests
= sequential (01–99) Test Purpose Number
number
---------------------- Page: 14 ----------------------
oSIST prEN 15876-1:2022
prEN 15876-1:2022 (E)
Annex A
(normative)
Test purposes for on-board equipment
A.1 Introduction

This annex contains the test purposes (TP) for the conformity evaluation of on-board equipment (OBE)

to FprEN 15509:2022.

OBE and OBU have been used as terms with the same or similar meaning in the standardization of DSRC

and DSRC-based EFC within CEN and ETSI. Previously developed relevant standards used the term OBU

with the meaning OBE as defined in this document. When referring to relevant tests in other documents,

this document uses the terms of the referenced source, which explains why the term OBU is often used in

this Annex
A.2 Physical Layer
A.2.1 BV Test Purposes
Test subgroup objective:

— to test the behaviour of the IUT in relation to syntactically and contextual correct behaviour of the

test system.
TP/PHY/OBU/BV/01 Dynamic range – sensitivity
TP Origin Identical to ETSI EN 300 674–1, 10.1.1
Reference FprEN 15509:2022, 6.1.2
Initial condition See ETSI EN 300 674–1, Clause 8.
Stimulus and Expected Behaviour
See ETSI EN 300 674–1, 10.1.1
TP/PHY/OBU/BV/02 Dynamic range – upper power limit for communication
TP Origin Identical to ETSI EN 300 674–1, 10.1.2
Reference FprEN 15509:2022, 6.1.2
Initial condition See ETSI EN 300 674–1, Clause 8.
Stimulus and Expected Behaviour
See ETSI EN 300 674–1, 10.1.2
---------------------- Page: 15 ----------------------
oSIST prEN 15876-1:2022
prEN 15876-1:2022 (E)
TP/PHY/OBU/BV/03 Cut-off power level
TP Origin Identical to ETSI EN 300 674–1, 10.2
Reference FprEN 15509:2022, 6.1.2
Initial condition See ETSI EN 300 674–1, Clause 8.
Stimulus and Expected Behaviour
See ETSI EN 300 674–1, 10.2
TP/PHY/OBU/BV/04 Conversion gain
TP Origin Identical to ETSI EN 300 674–1, 10.3
Reference FprEN 15509:2022, 6.1.2
Initial condition See ETSI EN 300 674–1, Clause 8.
Stimulus and Expected Behaviour
See ETSI EN 300 674–1, 10.3
TP/PHY/OBU/BV/05 Maximum equivalent isotropically radiated power
TP Origin Identical to ETSI EN 300 674–1, 10.4
Reference FprEN 15509:2022, 6.1.2
Initial condition See ETSI EN 300 674–1, Clause 8.
Stimulus and Expected Behaviour
See ETSI EN 300 674–1, 10.4
TP/PHY/OBU/BV/06 Frequency error
TP Origin Identical to ETSI EN 300 674–1, 10.5
Reference FprEN 15509:2022, 6.1.2
Initial condition See ETSI EN 300 674–1, Clause 8.
Stimulus and Expected Behaviour
See ETSI EN 300 674–1, 10.5
TP/PHY/OBU/BV/07 Transmitter spectrum mask
TP Origin Identical to ETSI EN 300 674–1, 10.6
Reference FprEN 15509:2022, 6.1.2
Initial condition See ETSI EN 300 674–1, Clause 8.
Stimulus and Expected Behaviour
See ETSI EN 300 674–1, 10.6
---------------------- Page: 16 ----------------------
oSIST prEN 15876-1:2022
prEN 15876-1:2022 (E)
TP/PHY/OBU/BV/08 Transmitter unwanted emissions
TP Origin Identical to ETSI EN 300 674–1, 10.7
Reference FprEN 15509:2022, 6.1.2
Initial condition See ETSI EN 300 674–1, Clause 8.
Stimulus and Expected Behaviour
See ETSI EN 300 674–1, 10.7
TP/PHY/OBU/BV/09 Receiver spurious emissions
TP Origin Identical to ETSI EN 300 674–1, 10.8
Reference FprEN 15509:2022, 6.1.2
Initial condition See ETSI EN 300 674–1, Clause 8.
Stimulus and Expected Behaviour
See ETSI EN 300 674–1, 10.8
A.2.2 BI Test Purposes
BI test purposes group do not apply for Layer 1.
A.3 MAC
A.3.1 BV Test Purposes
Test subgroup objective:

— to test the behaviour of the IUT in relation to syntactically and contextual correct behaviour of the

test system.
TP/MAC/OBU/BV/01 Receive downlink frames – maximum length
TP Origin Identical to ETSI/TS 102 486–1-2 TP/MAC/OBU/BV/01
Reference FprEN 15509:2022, 6.1.2
Initial condition See ETSI/TS 102 486–1-2 TP/MAC/OBU/BV/01
Stimulus and Expected Behaviour
See ETSI/TS 102 486–1-2 TP/MAC/OBU/BV/01
TP/MAC/OBU/BV/02 Receive downlink frames within T1
TP Origin Identical to ETSI/TS 102 486–1-2 TP/MAC/OBU/BV/02
Reference FprEN 15509:2022, 6.1.2
Initial condition See ETSI/TS 102 486–1-2 TP/MAC/OBU/BV/02
Stimulus and Expected Behaviour
See ETSI/TS 102 486–1-2 TP/MAC/OBU/BV/02
---------------------- Page: 17 ----------------------
oSIST prEN 15876-1:2022
prEN 15876-1:2022 (E)
TP/MAC/OBU/BV/03 Timing constraints for public uplink windows
TP Origin Identical to ETSI/TS 102 486–1-2 TP/MAC/OBU/BV/03
Reference FprEN 15509:2022, 6.1.2
Initial condition See ETSI/TS 102 486–1-2 TP/MAC/OBU/BV/03
Stimulus and Expected Behaviour
See ETSI/TS 102 486–1-2 TP/MAC/OBU/BV/03
TP/MAC/OBU/BV/04 Receive downlink frames within T2
TP Origin Identical to ETSI/TS 102 486–1-2 TP/MAC/OBU/BV/04
Reference FprEN 15509:2022, 6.1.2
Initial condition See ETSI/TS 102 486–1-2 TP/MAC/OBU/BV/04
Stimulus and Expected Behaviour
See ETSI/TS 102 486–1-2 TP/MAC/OBU/BV/04
TP/MAC/OBU/BV/05 Timing constraints for private uplink windows
TP Origin Identical to ETSI/TS 102 486–1-2 TP/MAC/OBU/BV/05
Reference FprEN 15509:2022, 6.1.2
Initial condition See ETSI/TS 102 486–1-2 TP/MAC/OBU/BV/05
Stimulus and Expected Behaviour
See ETSI/TS 102 486–1-2 TP/MAC/OBU/BV/05
TP/MAC/OBU/BV/06 S-bit and L-bit in MAC control field
TP Origin Identical to ETSI/TS 102 486–1-2 TP/MAC/OBU/BV/06
Reference FprEN 15509:2022, 6.1.2
Initial condition See ETSI/TS 102 486–1-2 TP/MAC/OBU/BV/06
Stimulus and Expected Behaviour
See ETSI/TS 102 486–1-2 TP/MAC/OBU/BV/06
TP/MAC/OBU/BV/07 Manage S-bit state variable
TP Origin Identical to ETSI/TS 102 486–1-2 TP/MAC/OBU/BV/07
Reference FprEN 15509:2022, 6.1.2
Initial condition See ETSI/TS 102 486–1-2 TP/MAC/OBU/BV/07
Stimulus and Expected Behaviour
See ETSI/TS 102 486–1-2 TP/MAC/OBU/BV/07
---------------------- Page: 18 ----------------------
oSIST prEN 15876-1:2022
prEN 15876-1:2022 (E)
TP/MAC/OBU/BV/08 Random selection of N5 public uplink windows
TP Origin Identical to ETSI/TS 102 486–1-2 TP/MAC/OBU/BV/08
Reference FprEN 15509:2022, 6.1.2
Initial condition See ETSI/TS 102 486–1-2 TP/MAC/OBU/BV/08
Stimulus and Expected Behaviour
See ETSI/TS 102 486–1-2 TP/MAC/OBU/BV/08
A.3.2 BI Test Purposes
Test subgroup objective:

— to check the behaviour of the IUT in response to invalid stimuli and behaviour from the test tool.

TP/MAC/OBU/BI/01 Manage double-bit errors in the LID, MAC control and LPDU fields

TP Origin Identical to ETSI/TS 102 486–1-2 TP/MAC/OBU/BI/01
Reference FprEN 15509:2022, 6.1.2
Initial condition See ETSI/TS 102 486–1-2 TP/MAC/OBU/BI/01
Stimulus and Expected Behaviour
See ETSI/TS 102 486–1-2 TP/MAC/OBU/BI/01
TP/MAC/OBU/BI/02 Detect and manage dou
...