EN 13480-6:2017/A1:2019

Metallic industrial piping - Part 6: Additional requirements for buried piping

This European Standard specifies requirements for industrial piping either totally buried or partly buried and partly run in sleeves or similar protection. It is used in conjunction with the other six parts of EN 13480. Where buried piping subject to this standard connects to piping installed under other jurisdiction such as pipelines, the transition should be made at a closing element e.g. an isolating or regulating valve separating the two sections. This should be close to the boundary of the industrial site, but may be inside or outside the boundary. Operating temperature up to 75 °C. NOTE For higher temperatures reference should be made to EN 13941, but it should be kept in mind, that CEN/TC 107 only deals with pre-insulated piping with temperatures up to 140 °C and diameters up to 800 mm, which is state of the art for these products.

Metallische industrielle Rohrleitungen - Teil 6: Zusätzliche Anforderungen an erdgedeckte Rohrleitungen

Tuyauteries industrielles métalliques - Partie 6 : Exigences complémentaires pour les tuyauteries enterrées

Kovinski industrijski cevovodi - 6. del: Dodatne zahteve za vkopane cevovode - Dopolnilo A1

General Information

• Status: Withdrawn
• Publication Date: 16-Apr-2019
• Withdrawal Date: 23-Jul-2024
• ICS: 23.040.01 - Pipeline components and pipelines in general
• Technical Committee: CEN/TC 267 - Industrial piping and pipelines
• Drafting Committee: CEN/TC 267/WG 1 - General
• Directive: 2014/68/EU - Directive 2014/68/EU of the European Parliament and of the Council of 15 May 2014 on the harmonisation of the laws of the Member States relating to the making available on the market of pressure equipment
• Directive: 97/23/EC - Directive 97/23/EC of the European Parliament and of the Council of 29 May 1997 on the approximation of the laws of the Member States concerning pressure equipment
• Mandate: M/071 - Mandate to CEN for standardization in the field of Pressure equipment
• Ref Project: SIST EN 13480-6:2018/A1:2019 - Metallic industrial piping - Part 6: Additional requirements for buried piping

Relations

• Replaced By: EN 13480-6:2024 - Metallic industrial piping - Part 6: Additional requirements for buried piping
• Effective Date: 31-Jul-2024
• Amends: EN 13480-6:2017 - Metallic industrial piping - Part 6: Additional requirements for buried piping
• Effective Date: 06-Dec-2017

Standards Content (Sample)

SLOVENSKI STANDARD
01-september-2019
Kovinski industrijski cevovodi - 6. del: Dodatne zahteve za vkopane cevovode -
Dopolnilo A1
Metallic industrial piping - Part 6: Additional requirements for buried piping
Metallische industrielle Rohrleitungen - Teil 6: Zusätzliche Anforderungen an
erdgedeckte Rohrleitungen
Tuyauteries industrielles métalliques - Partie 6: Exigences complémentaires relatives aux
tuyauteries enterrées
Ta slovenski standard je istoveten z: EN 13480-6:2017/A1:2019
ICS:
23.040.10 Železne in jeklene cevi Iron and steel pipes
77.140.75 Jeklene cevi in cevni profili Steel pipes and tubes for
za posebne namene specific use
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN 13480-6:2017/A1
EUROPEAN STANDARD
NORME EUROPÉENNE
April 2019
EUROPÄISCHE NORM
ICS 23.040.01
English Version
Metallic industrial piping - Part 6: Additional requirements
for buried piping
Tuyauteries industrielles métalliques - Partie 6 : Metallische industrielle Rohrleitungen - Teil 6:
Exigences complémentaires pour les tuyauteries Zusätzliche Anforderungen an erdgedeckte
enterrées Rohrleitungen
This amendment A1 modifies the European Standard EN 13480-6:2017; it was approved by CEN on 1 March 2019.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of
this amendment into the relevant national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This amendment exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 13480-6:2017/A1:2019 E
worldwide for CEN national Members.

Contents
European foreword . 3
1 Modification to 5.2, Design . 4
2 Modification to A.3.2.2, Notations . 4
3 Modification to A.3.2.3, Soil properties . 4
4 Modifications to A.3.2.5.1, Definition . 4
5 Modifications to A.3.3.2, Distributed live load . 5
6 Modification to A.3.5.6.2, Longitudinal compressive stress in the restrained part . 5
7 Modification to Annex ZA (informative), Relationship between this European
Standard and the Essential Requirements of EU Directive 2014/68/EU aimed to be
covered. 5

European foreword
This document (EN 13480-6:2017/A1:2019) has been prepared by Technical Committee CEN/TC 267
“Industrial piping and pipelines”, the secretariat of which
...