EN 1279-5:2005
(Main)Glass in building - Insulating glass units - Part 5: Evaluation of conformity
Glass in building - Insulating glass units - Part 5: Evaluation of conformity
This document specifies requirements, the evaluation of conformity and the factory production control of insulating glass units for use in buildings.
NOTE 1 For glass products with electrical wiring or connections for e.g. alarm or heating purposes, other directives, e.g. Low Voltage Directive, may apply.
The main intended uses of the insulating glass units are installations in windows, doors, curtain walling, roofs and partitions where there exists protection against direct ultraviolet radiation at the edges.
NOTE 2 In cases where there is no protection against direct ultra-violet radiation at the edges, such as structural sealant glazing systems, additional European technical specifications should be followed (e.g. prEN XXX, prEN 13022-1).
NOTE 3 Units for which the intended use is only 'artistic' and therefore no essential requirement is required, are not subject to CE marking and are not part of this document.
Glas im Bauwesen - Mehrscheiben-Isolierglas - Teil 5: Konformitätsbewertung
Diese Euroäische Norm legt Anforderungen an sowie die Konformitätsbewertung und die werkseigene
Produktionskontrolle für Mehrscheiben-Isolierglas zur Verwendung in Gebäuden fest.
ANMERKUNG 1 Für Glasprodukte mit elektrischer Verdrahtung oder elektrischen Anschlüssen, z. B. zu Alarm- oder
Heizzwecken, gelten möglicherweise weitere Richtlinien, z. B. die Niederspannungsrichtlinie.
Der vorgesehene Hauptverwendungszweck der Mehrscheiben-Isoliergläser ist der Einbau in Fenster, Türen,
Vorhangfassaden, Dächer und Trennwände, wobei die Ränder des Glases gegen direkte UV-Strahlung
geschützt sind.
ANMERKUNG 2 Falls die Ränder nicht gegen direkte UV-Strahlung geschützt sind, wie z. B. bei geklebten
Verglasungen (�Structural Sealant Glazingiu-Systeme), sollten zusätzliche Europäische Technische Spezifikationen befolgt
werden (z. B. 00129113, prEN 13022-1).
ANMERKUNG 3 Einheiten, die nur für �künstlerischeim Zwecke vorgesehen sind und für die daher keine wesentlichen
Anforderungen gelten, sind nicht Gegenstand der CE-Kennzeichnung und werden von dieser Europäischen Norm nicht
erfasst.
Verre dans la construction - Vitrage isolant - Partie 5: Evaluation de la conformité
La présente Norme européenne spécifie des exigences relatives à l'évaluation de la conformité et au contrôle de la production en usine des vitrages isolants utilisés dans la construction.
NOTE 1 Pour les produits verriers équipés d'un câblage ou de branchements électriques pour les besoins d'alarme ou de chauffage, par exemple, d'autres directives, comme par exemple la Directive "Basse(s) Tension(s)", peuvent s'appliquer.
Les usages prévus des vitrages isolants sont principalement les installations dans des fenêtres, portes, murs rideaux, toitures et cloisons offrant une protection des bords contre les rayonnements ultraviolets directs.
NOTE 2 En l'absence de protection contre les rayonnements ultraviolets directs sur les bords, comme par exemple pour les vitrages extérieurs collés, il convient de se conformer à d'autres spécifications techniques européennes (par exemple 00129113, prEN 13022-1).
NOTE 3 Les vitrages de nature purement "artistique", et pour lesquels aucune exigence essentielle n'est requise, ne sont pas soumis au marquage CE et ne sont pas couverts par la présente Norme européenne.
Steklo v gradbeništvu – Izolacijsko steklo – 5. del: Ovrednotenje skladnosti
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Glass in building - Insulating glass units - Part 5: Evaluation of conformitySteklo v gradbeništvu – Izolacijsko steklo – 5. del: Ovrednotenje skladnostiVerre dans la construction - Vitrage isolant - Partie 5: Evaluation de la conformitéGlas im Bauwesen - Mehrscheiben-Isolierglas - Teil 5: Konformitätsbewertung81.040.20Steklo v gradbeništvuGlass in buildingICS:SIST EN 1279-5:2005enTa slovenski standard je istoveten z:EN 1279-5:200501-september-2005SIST EN 1279-5:2005SLOVENSKI
STANDARD
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 1279-5May 2005ICS 81.040.20English versionGlass in building - Insulating glass units - Part 5: Evaluation ofconformityVerre dans la construction - Vitrage isolant préfabriquéscellé - Partie 5: Evaluation de la conformitéGlas im Bauwesen - Mehrscheiben-Isolierglas - Teil 5:KonformitätsbewertungThis European Standard was approved by CEN on 24 March 2005.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2005 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 1279-5:2005: E
Use of IGUs when subjected to UV and/or in SSG.17 Annex B (informative)
Installation of the insulating glass units.18 Annex C (informative)
Provisions for voluntary involvement of third party(ies).21 Annex ZA (informative)
Clauses of this European Standard addressing the provisions of EU Construction Products Directive.22 Bibliography.31
fire resistance tests, excluding ventilation services prEN 13501-5, Fire classification of construction products and building elements – Part 5: Classification using data from external fire exposure to roof tests EN 13541, Glass in building – Security glazing – Testing and classification of resistance against explosion pressure EN 14178-1, Glass in building – Basic alkaline earth silicate glass products – Part 1: Float glass EN ISO 12543-1, Glass in building – Laminated and laminated safety glass - Part 1: Definition and description of component parts (ISO 12543-1:1998)
3 Terms and definitions For the purposes of this European Standard, the terms and definitions given in EN 1279-1:2004, EN 1279-2:2002, EN 1279-3:2002, EN 1279-4:2002 and EN 1279-6:2002 and the following apply. 3.1 initial type testing determination of the performance of a product (characteristic, durability), on the basis of either actual tests or other procedures (such as conventional, standardised, tabulated or general accepted values, standardised or recognised calculation methods, test reports when made available,), in accordance with this European Standard that demonstrates compliance with this European Standard 3.2 test report document that covers the results of tests undertaken on a representative sample of the product from production or on a prototype design of the product 3.3 product description document that details the relevant parameters, e.g. process conditions, structure, etc, for defining a product that complies with the standard. It includes specific references to characteristics that are modified by the production process
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.