iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 500-6:2006+A1:2008

(Main)

Mobile road construction machinery - Safety - Part 6: Specific requirements for paver-finishers

Mobile road construction machinery - Safety - Part 6: Specific requirements for paver-finishers

This part of EN 500 specifies the safety requirements for paver-finishers as defined in Clause 3 and deals with the significant hazards relevant to these machines, when they are used as intended and under conditions of misuse which are reasonably foreseeable. This part of EN 500 contains additional requirements to EN 500-1 "Common requirements".
If internal and/or external vibrators are used for concrete paving, then prEN 12649 applies.

Bewegliche Straßenbaumaschinen - Sicherheit - Teil 6: Besondere Anforderungen an Straßenfertiger

Machines mobiles pour la construction de routes - Sécurité - Partie 6 : Prescriptions spécifiques pour finisseurs

La présente partie de l'EN 500 précise les prescriptions de sécurité pour les finisseurs tels que définis à l’Article 3 et traite des phénomènes dangereux significatifs relatifs aux machines lorsqu’elles sont utilisées normalement et dans des conditions de mauvaise utilisation qui sont raisonnablement prévisibles. La présente partie de l'EN 500 fournit des prescriptions complémentaires à l'EN 500-1+A1 «Prescriptions communes».
Si des vibreurs internes et/ou externes sont utilisés pour le bétonnage, !l’EN 12649" s’applique.

Premični stroji za gradnjo cest - Varnost - 6. del: Posebne zahteve za finišerje za ceste

General Information

Status
Published
Publication Date
07-Oct-2008
ICS
93.080.10 - Road construction
Technical Committee
CEN/TC 151 - Construction equipment and building material machines - Safety
Drafting Committee
CEN/TC 151/WG 5 - Road construction machines - Safety
Current Stage
9093 - Decision to confirm - Review Enquiry
Completion Date
14-Jun-2018
Directive
2006/42/EC - Directive 2006/42/EC of the European Parliament and of the Council of 17 May 2006 on machinery, and amending Directive 95/16/EC (recast)
98/37/EC - Machinery
Mandate
M/079 - Mandate to CEN and CENELEC for standardization in the field of machines
M/396 - Mandate to CEN and Cenelec for standardisation in the field of machinery
Ref Project
SIST EN 500-6:2007+A1:2008 - Mobile road construction machinery - Safety - Part 6: Specific requirements for paver-finishers

Relations

Merged From
EN 500-6:2006 - Mobile road construction machinery - Safety - Part 6: Specific requirements for paver-finishers
Effective Date
18-Jan-2023
Revised
prEN ISO 20500-6 - Mobile road construction machinery - Safety - Part 6: Specific requirements for paver-finishers
Effective Date
18-Jan-2023

Buy Standard

EN 500-6:2007+A1:2008EN 500-6:2007+A1:2008
PreviousNext
Standard
EN 500-6:2007+A1:2008
English language
29 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-december-2008
3UHPLþQLVWURML]DJUDGQMRFHVW9DUQRVWGHO3RVHEQH]DKWHYH]DILQLãHUMH]D
FHVWH
Mobile road construction machinery - Safety - Part 6: Specific requirements for paver-
finishers
Bewegliche Straßenbaumaschinen - Sicherheit - Teil 6: Besondere Anforderungen an
Straßenfertiger
Machines mobiles pour la construction de routes - Sécurité - Partie 6 : Prescriptions
spécifiques pour finisseurs
Ta slovenski standard je istoveten z: EN 500-6:2006+A1:2008
ICS:
93.080.10 Gradnja cest Road construction
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN 500-6:2006+A1
NORME EUROPÉENNE
EUROPÄISCHE NORM
October 2008
ICS 93.080.10 Supersedes EN 500-6:2006
English Version
Mobile road construction machinery - Safety - Part 6: Specific
requirements for paver-finishers
Machines mobiles pour la construction de routes - Sécurité Bewegliche Straßenbaumaschinen - Sicherheit - Teil 6:
- Partie 6: Prescriptions spécifiques pour finisseurs Besondere Anforderungen an Straßenfertiger
This European Standard was approved by CEN on 17 August 2006 and includes Amendment 1 approved by CEN on 25 August 2008.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.

EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2008 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 500-6:2006+A1:2008: E
worldwide for CEN national Members.

Contents Page
Foreword.4
Introduction .5
1 Scope .6
2 Normative references .6
3 Terms and definitions .6
4 List of significant hazards .7
5 Safety requirements and/or protective measures.7
5.1 Lighting, signalling and marking lights and reflex-reflector devices.7
5.2 Operation and handling .7
5.3 Operator's station .7
5.4 Operator's seat.7
5.5 Controls and indicators .7
5.6 Starting .7
5.7 Stopping .8
5.8 Access systems to operator's station and to maintenance points .8
5.9 Protection .8
5.10 Pressurised systems.8
5.11 Fire protection.8
5.12 Hot surfaces .8
5.13 Signal devices and warning signs .8
5.14 Liquid gas units .8
5.15 Electrical and electronic systems.9
5.16 Electro-magnetic compatibility (EMC).9
5.17 Noise and vibration.9
5.18 Conveyors .9
6 Verification of safety requirements and/or protective measures .9
7 Information for the user .9
7.1 Warning signals and devices .9
7.2 Instruction handbook .9
7.3 Marking .9
Annex A (normative) Braking systems of rubber-tyred paver-finishers – Performance requirements
and test procedures .10
Annex B (normative) Noise test code for paver-finishers .12
Annex C (normative) Noise test code for slipform pavers .17
Annex D (informative) Examples of paver-finishers .22
Annex ZA (informative) Relationship between this European Standard and the Essential
Requirements of EC Directive 98/37/EC .27
Annex ZB (informative) !!!!Relationship between this European Standard and the Essential
Requirements of EU Directive 2006/42/EC"""".28
Bibliography .29

Figures
Figure B.1 .13
Figure B.2 .13
Figure B.3 — Microphone positions .13
Figure C.1 .17
Figure C.2 .17
Figure C.3 — Microphone positions .18
Figure D.2 — Crawler-mounted paver-finisher.23
Figure D.3 — Pre-compaction screed.23
Figure D.4 — Compaction screed with vibration .24
Figure D.5 — Compaction screed with tamper bar .24
Figure D.6 — High-compaction screed with tamper bar and vibration.25
Figure D.7 — High-compaction screed with tamper bar, vibration and two pressure bars .25
Figure D.8 — Slipform paver with offset mould .26
Figure D.9 — Slipform paver with road mould .26

Tables
Table 1.7
Table B.1 — Settings for simulation to determine noise emission of a paver-finisher while paving.15
Table C.1 — Settings for simulation to determine noise emission of a slipform paver while paving.19

Foreword
This document (EN 500-6:2006+A1:2008) has been prepared by Technical Committee CEN/TC 151 “Construction
equipment and building material machines — Safety”, the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an identical text or
by endorsement, at the latest by April 2009, and conflicting national standards shall be withdrawn at the latest by
December 2009.
This document includes Amendment 1, approved by CEN on 2008-08-25.
This document supersedes !EN 500-6:2006".
The start and finish of text introduced or altered by amendment is indicated in the text by tags ! ".
This document has been prepared under a mandate given to CEN by the European Commission and the European
Free Trade Association, and supports essential requirements of EU Directive(s).
!For relationship with EU Directive(s), see informative Annexes ZA and ZB, which are integral parts of this
document."
EN 500 ”Mobile road construction machinery — Safety” comprises the following parts:
 Part 1: Common requirements;
 Part 2: Specific requirements for road-milling machines;
 Part 3: Specific requirements for soil-stabilising machines and recycling machines;
 Part 4: Specific requirements for compaction machines;
 Part 6: Specific requirements for paver-finishers.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following coun-
tries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Den-
mark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg,
Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and
United Kingdom.
Introduction
This European Standard is a type C standard as stated in EN ISO 12100-1.
The machinery concerned and the extent to which hazards, hazardous situations and events are covered are indi-
cated in the scope of this European Standard.
When provisions of this type C standard are different from those which are stated in type A or B standards, the pro-
visions of this type C standard take precedence over the provisions of the other standards for machines that have
been designed and built according to the provisions of this type C standard.
1 Scope
This part of EN 500 specifies the safety requirements for paver-finishers as defined in Clause 3 and deals with the
significant hazards relevant to these machines, when they are used as intended and under conditions of misuse
which are reasonably foreseeable. This part of EN 500 contains additional requirements to EN 500-1 “Common
requirements”.
If internal and/or external vibrators are used for concrete paving, then prEN 12649 applies.
2 Normative references
The following referenced documents are indispensable for t
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN 13862:2021(Main)
Floor cutting-off machines - Safety
SIST EN 13862:2022

This document applies to pedestrian-controlled floor-sawing machines having travel power feed or manual feed (see 3.1) for sawing, grooving and milling floor surfaces made of concrete, asphalt and similar mineral building materials where the main power is supplied by electric or internal combustion prime engine. The power transmission of floor-sawing machines is mechanical or hydraulic.
This document deals with all significant hazards, hazardous situations or hazardous events relevant to floor sawing machines, when they are used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer (see Annex A). This document specifies the appropriate technical measures to eliminate or reduce risks arising from the significant hazards during the lifetime of the machinery as described in EN ISO 12100:2010, 5.4.
These machines are designed for use with rotating cutting-off wheels for wet and dry cutting. These cutting-off wheels can be either a diamond cutting-off wheel or a boron nitride cutting-off wheel.
This document does not apply to:
-   self-propelled ride-on floor-sawing machines;
-   machines moving along a rail;
-   hand-held portable cutting off machines for construction materials mounted on a mobile support, to be used as floor saws;
-   remote-controlled machines.
In this document, floor-sawing machines are called “machines”, and cutting-off wheels are also called “tools”.
This document applies to machines which are manufactured after the date of approval of the standard by CEN.

  • Standard
    50 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13020:2015(Main)
Road surface treatment machines - Safety requirements
SIST EN 13020:2016

This European Standard applies to road surface treatment machines, which are in particular:
-   binder sprayers [or sprayers];
-   chipping spreaders [or spreaders];
-   machines for surface repairs (binder sprayer chipping spreader [or sprayer spreader]);
-   mastics asphalt mixers;
-   joint sealer;
-   micro-surfacing machines/slurry machines;
-   cold asphalt laying / micro-asphalt-paving machines
(see also Clause 3).
Road surface treatment machines can be mounted on a carrier vehicle, trailer or articulated truck, combining to form an integral unit. It is also possible to mount a road surface treatment machine on its own chassis construction and propulsion system (self-propelled or pedestrian-controlled). In all cases the machine and chassis form an integral unit.
Directives and standards for the vehicular truck chassis aspects, termed 'carrier vehicle' in this document, would be those relative to that equipment, even where specific modifications have been made to realize the road surface treatment application. The use in public road traffic is governed by the national regulations.
This European Standard deals with all significant hazards identified through a risk assessment relevant to road surface treatment machines when they are used as intended and under the conditions foreseen by the manufacturer (see Clause 4). This European Standard does not deal with significant hazards associated with pressurized tanks, and EMC. This European Standard specifies the appropriate technical measures to eliminate or reduce risks arising from the significant hazards associated with machine operation, setting and adjustments, load discharge and routine maintenance.
This European Standard does not include requirements for the carrier vehicles or special constructions. These are covered in directives related to the construction of vehicles. Demountable bodywork systems (e.g. demountable containers) are specified in other standards. Vibrations are not dealt with in the standard, because for all machines of this family vibration is not a relevant hazard due to the low working speed and special working conditions (e.g. flat surface).
This European Standard does not deal with the risks associated with the operation of the machines in potentially explosive atmospheres.
This European Standard does not include requirements of the 94/55/EC Directive related to transport of dangerous goods by road but contains additional specifications in link with these existing requirements.
This European Standard applies to machines which are manufactured after the date of approval of this standard by CEN.

  • Standard
    39 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 536:2015(Main)
Road construction machines - Mixing plants for road construction materials - Safety requirements
SIST EN 536:2015

This European Standard specifies the safety requirements applicable to stationary and relocatable mixing plants for the production of materials (e.g. hot-mix asphalt, cold-mix asphalt, cement gravel) used for the construction and maintenance of traffic routes (roads, highways, sidewalks, airfields, etc.) water retaining works, dam walls, culverts, etc.
This European Standard applies to the following types of mixing plant:
a)   hot Asphalt mixing plant;
b)   cold mixing plant (e.g. for production of cement gravel, cold mix asphalt);
c)   mixing plant for bituminous or non-bituminous reclaimed materials;
d)   mixing plant for mastic asphalt, also including natural asphalt.
Machines moving during the working process (e.g. mobile mastic asphalt mixers) and crushers are not covered by this European Standard.
Those types of asphalt mixing plants can also be combined or enlarged by additional installations (e.g. Plant for storage of binders (e.g. bituminous, synthetic, vegetal).
This European Standard deals with all significant hazards pertinent to mixing plants, when they are used as intended and under the conditions of misuse which are reasonably foreseen by the manufacturer (see Clause 4). This European Standard specifies the appropriate technical measures to eliminate or reduce risks arising from the significant hazards.
This European Standard does not apply to machines for the production of cement concrete and mortar as covered in EN 12151.
This European Standard does not deal with hazards caused by flammable gases. As soon as information is available it will be included.
This European Standard is not applicable to mixing plants for road construction materials, which are manufactured before the date of publication of this European Standard by CEN.

  • Standard
    60 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 500-1:2006+A1:2009(Main)
Mobile road construction machinery - Safety - Part 1: Common requirements
SIST EN 500-1:2007+A1:2010

1.1   This part of EN 500 specifies the common safety requirements for mobile road construction machinery ). The EN 500 series is applicable to mobile road construction machinery as listed in Annex A. When no specific standard exists, EN 500-1 applies.
It specifies common requirements for the design and construction of mobile road construction machinery in order to protect workers from accidents and health hazards which could occur during operation, loading, transport and maintenance.
Additional specific requirements for certain types of mobile road construction machinery are given in parts 2 to 4 and 6 of this standard.
This part of this standard gives safety requirements for all types of mobile road construction machinery and shall be used in conjunction with one of the parts 2 to 4 and 6. These machine-specific parts do not repeat the requirements from part 1 but add to or replace the requirements for the type of mobile road construction machinery in question.
Machine-specific requirements in parts 2 to 4 and 6 take precedence over the respective requirements of this stan-dard.
For types of mobile road construction machinery not dealt with in parts 2 to 4 and 6, EN 500-1 applies and if for those machinery additional derived risks may arise, these risks have to be taken into consideration.
1.2   This European Standard deals with all significant hazards, hazardous situations and events relevant to mobile road construction machinery, when they are used as intended and under conditions of misuse which are reasonably foreseeable (see Clause 4).
This European Standard specifies the appropriate technical measures to eliminate or reduce risks arising from the significant hazards as specified in Clause 4.
1.3   This European Standard applies to machines which are manufactured after the date of publication of this European Standard by CEN.

  • Standard
    51 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 500-3:2006+A1:2008(Main)
Mobile road construction machinery - Safety - Part 3: Specific requirements for soil-stabilising machines and recycling machines
SIST EN 500-3:2007+A1:2008

This part of EN 500 specifies the safety requirements for soil-stabilising machines and recycling machines as de-fined in Clause 3 and deals with all significant hazards, hazardous situations and events relevant to these ma-chines, when they are used as intended and under conditions of misuse which are reasonably foreseeable.
This part of EN 500 contains additional requirements to EN 500-1 "Common requirements".

  • Standard
    22 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 500-2:2006+A1:2008(Main)
Mobile road construction machinery - Safety - Part 2: Specific requirements for road-milling machines
SIST EN 500-2:2007+A1:2008

This part of EN 500 specifies the safety requirements for road-milling machines as defined in Clause 3 and deals with all significant hazards, hazardous situations and events relevant to these machines, when they are used as intended and under conditions of misuse which are reasonably foreseeable.
This part of EN 500 contains additional requirements to EN 500-1 "Common requirements".

  • Standard
    21 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
prEN ISO 20500-6(Main)
Mobile road construction machinery - Safety - Part 6: Specific requirements for paver-finishers
oSIST prEN ISO 20500-6:2020

This part of EN 500 specifies the safety requirements for paver-finishers as defined in Clause 3 and deals with the significant hazards relevant to these machines, when they are used as intended and under conditions of misuse which are reasonably foreseeable. This part of EN 500 contains additional requirements to EN 500-1 "Common requirements". If internal and/or external vibrators are used for concrete paving, then prEN 12649 applies.

  • Draft
    32 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
prEN ISO 20500-4(Main)
Mobile road construction machinery - Safety - Part 4: Specific requirements for compaction machines
oSIST prEN ISO 20500-4:2020

This part of EN 500 specifies the safety requirements for compaction machines as defined in Clause 3 and deals with all significant hazards, hazardous situations and events relevant to compaction machines, when they are used as intended and under conditions of misuse which are reasonably foreseeable. This document specifies additional requirements to and/or exceptions from EN 500-1 "Common requirements".

  • Draft
    52 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
prEN ISO 20500-3(Main)
Mobile road construction machinery - Safety - Part 3: Specific requirements for soil-stabilising machines and recycling machines
oSIST prEN ISO 20500-3:2020

This part of EN 500 specifies the safety requirements for soil-stabilising machines and recycling machines as defined in Clause 3 and deals with all significant hazards, hazardous situations and events relevant to these machines, when they are used as intended and under conditions of misuse which are reasonably foreseeable. This part of EN 500 contains additional requirements to EN 500-1 "Common requirements".

  • Draft
    35 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
prEN ISO 20500-2(Main)
Mobile road construction machinery - Safety - Part 2: Specific requirements for road-milling machines
oSIST prEN ISO 20500-2:2020

This part of EN 500 specifies the safety requirements for road-milling machines as defined in Clause 3 and deals with all significant hazards, hazardous situations and events relevant to these machines, when they are used as intended and under conditions of misuse which are reasonably foreseeable. This part of EN 500 contains additional requirements to EN 500-1 "Common requirements".

  • Draft
    60 pages
    English language
    sale 10% off
    e-Library read for
    1 day