EN 6038:2015
(Main)Aerospace series - Fibre reinforced plastics - Test method - Determination of the compression strength after impact
Aerospace series - Fibre reinforced plastics - Test method - Determination of the compression strength after impact
This European Standard defines a method to be used to measure the low speed impact resistance characteristics of fibre reinforced plastics.
It is applicable to composite laminates with unidirectional plies or woven fabric reinforcement.
This standard does not give any direction necessary to meet health and safety requirements. It is the responsibility of the user of this standard to consult and establish appropriate health and safety precautions.
Luft- und Raumfahrt - Faserverstärkte Kunststoffe - Prüfverfahren - Bestimmung der Restdruckfestigkeit nach Schlagbeanspruchung
Série aérospatiale - Matières plastiques renforcées de fibres - Méthode d'essai - Détermination de la résistance en compression après impact
La présente norme européenne définit la méthode qui doit être utilisée pour mesurer les caractéristiques de résistance à l’impact à basse vitesse des plastiques renforcés de fibres.
La présente norme est applicable aux laminés composites fabriqués à partir d’un renforcement par bande unidirectionnelle ou tissu.
La présente norme ne contient aucune des instructions nécessaires à la satisfaction des exigences en matière d’hygiène et de sécurité. Il est de la responsabilité de l’utilisateur de la présente norme de consulter et d’établir des précautions d’hygiène et de sécurité appropriées
Aeronavtika - Z vlakni ojačeni polimerni materiali - Preskusna metoda - Ugotavljanje tlačne odpornosti po udarcu
Ta evropski standard določa metodo, ki se uporablja za merjenje odpornosti z vlakni ojačenih polimernih materialov po udarcu pri nizki hitrosti.
Uporablja se za kompozitne laminate z enosmernim sukanjem ali iz z vlakni ojačenega materiala. Ta standard ne vsebuje nobenih smernic, potrebnih za izpolnjevanje zdravstvenih in varnostnih zahtev. Uporabnik tega standarda se mora posvetovati in določiti ustrezne zdravstvene in varnostne ukrepe.
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
01-januar-2016
$HURQDYWLND=YODNQLRMDþHQLSROLPHUQLPDWHULDOL3UHVNXVQDPHWRGD
8JRWDYOMDQMHWODþQHRGSRUQRVWLSRXGDUFX
Aerospace series - Fibre reinforced plastics - Test method - Determination of the
compression strength after impact
Luft- und Raumfahrt - Faserverstärkte Kunststoffe - Prüfverfahren - Bestimmung der
Restdruckfestigkeit nach Schlagbeanspruchung
Série aérospatiale - Matières plastiques renforcées de fibres - Méthode d'essai -
Détermination de la résistance en compression après impact
Ta slovenski standard je istoveten z: EN 6038:2015
ICS:
49.025.40 Guma in polimerni materiali Rubber and plastics
83.120 2MDþDQLSROLPHUL Reinforced plastics
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN 6038
EUROPEAN STANDARD
NORME EUROPÉENNE
November 2015
EUROPÄISCHE NORM
ICS 49.025.40
English Version
Aerospace series - Fibre reinforced plastics - Test method -
Determination of the compression strength after impact
Série aérospatiale - Matières plastiques renforcées de Luft- und Raumfahrt - Faserverstärkte Kunststoffe -
fibres - Méthode d'essai - Détermination de la Prüfverfahren - Bestimmung der Restdruckfestigkeit
résistance en compression après impact nach Schlagbeanspruchung
This European Standard was approved by CEN on 21 June 2014.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2015 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 6038:2015 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
1 Scope . 4
2 Normative references . 4
3 Terms and definitions . 4
4 Principle of the method . 4
5 Designation of the method . 5
6 Apparatus . 5
7 Test specimen . 5
8 Procedure. 6
9 Presentation of the results . 7
10 Test report . 8
European foreword
This document (EN 6038:2015) has been prepared by the Aerospace and Defence Industries
Association of Europe - Standardization (ASD-STAN).
After enquiries and votes carried out in accordance with the rules of this Association, this Standard has
received the approval of the National Associations and the Official Services of the member countries of
ASD, prior to its presentation to CEN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by May 2016, and conflicting national standards shall be
withdrawn at the latest by May 2016.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent
rights.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
1 Scope
This European Standard defines a method to be used to measure the low speed impact resistance
characteristics of fibre reinforced plastics.
It is applicable to composite laminates with unidirectional plies or woven fabric reinforcement.
This standard does not give any direction necessary to meet health and safety requirements. It is the
responsibility of the user of this standard to consult and establish appropriate health and safety
precautions.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
EN 2374, Aerospace series — Glass fibre reinforced mouldings and sandwich composites — Production of
test panels
1)
EN 2565, Aerospace series — Preparation of carbon fibre reinforced resin panels for test purposes
EN 2743, Aerospace series — Fibre reinforced plastics — Standard procedures for conditioning prior to
testing unaged materials
1)
EN 2760, Aerospace series — Steel FE-PL78 — 1 760 ≤ R ≤ 2 000 MPa — Bar — D≤ 75 mm
m e
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
3.1
compression strength after impact
maximum compression load experienced by the impacted specimen divided by the initial gross cross
sectional area
4 Principle of the method
Subject the laminate specimen to impacts of varying energy, then measure the indentation depth and
the compression strength after impact.
1) Published as ASD-STAN Prestandard at the date of
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.