EN 16236:2013
(Main)Evaluation of conformity of aggregates - Initial Type Testing and Factory Production Control
Evaluation of conformity of aggregates - Initial Type Testing and Factory Production Control
This European Standard specifies both initial type testing and factory production control requirements for use during the evaluation and production of aggregates.
Additional testing carried out within contracts is beyond the scope of this standard.
This European Standard is applicable to European Standards for aggregates if regulatory marking of conformity is to be applied. It is also applicable to European Standards for aggregates where regulatory marking does not apply.
This European Standard is applicable to the control of aggregates within the scope of EN 12620, EN 13043, EN 13242, EN 13139, EN 13383-1 and EN 13450.
Bewertung der Konformität von Gesteinskörnungen - Erstprüfung und werkseigene Produktionskontrolle
Diese Europäische Norm legt die Anforderungen an die Erstprüfung und die werkseigene Produktionskontrolle
zur Anwendung bei der Bewertung und Produktion von Gesteinskörnungen fest.
Im Rahmen von Verträgen zusätzlich ausgeführte Prüfungen gehen über den Anwendungsbereich der
vorliegenden Norm hinaus.
Diese Europäische Norm ist auf Europäische Normen für Gesteinskörnungen anwendbar, wenn die gesetzlich
geregelte Konformitätskennzeichnung zur Anwendung kommen muss. Sie gilt auch für Europäische Normen
für Gesteinskörnungen, in Situationen, wo die gesetzliche geregelte Kennzeichnung nicht anwendbar ist.
Diese Europäische Norm ist zur Überprüfung von Gesteinskörnungen innerhalb des Anwendungsbereichs von
EN 12620, EN 13043, EN 13242, EN 13139, EN 13383-1 und EN 13450 anwendbar.
Évaluation de la conformité des granulats - Contrôle de la production en usine
La présente Norme européenne spécifie les exigences relatives aux essais de type initiaux et au contrôle de
la production en usine de granulats applicables lors de l’évaluation et de la production des granulats.
Les essais supplémentaires réalisés dans le cadre de contrats ne font pas partie du domaine d’application de
la présente norme.
La présente Norme européenne s’applique aux Normes européennes relatives aux granulats lorsqu’il est
prévu d’apposer un marquage réglementaire de conformité. Elle s’applique également aux Normes
européennes pour les granulats où le marquage réglementaire n’est pas apposé.
La présente Norme européenne est applicable pour la maîtrise des granulats faisant partie du domaine
d’application de l’EN 12620, l’EN 13043, l’EN 13242, l’EN 13139, l’EN 13383-1 et de l’EN 13450.
Vrednotenje skladnosti agregatov - Začetno preskušanje tipa in kontrola proizvodnje v obratu
Ta evropski standard določa tako začetno tipsko preskušanje kot zahteve za kontrolo proizvodnje v obratu za uporabo med vrednotenjem in proizvodnjo agregatov. Dodatno preskušanje po pogodbah ne sodi v področje uporabe tega standarda. Ta evropski standard se uporablja v evropskih standardih za agregate, če se uporablja regulirano označevanje skladnosti. Uporablja se tudi v evropskih standardih za agregate, kjer se regulirano označevanje ne uporablja. Ta evropski standard se uporablja za nadzor agregatov, ki sodijo v področje uporabe standardov EN 12620, EN 13043, EN 13242, EN 13139, EN 13383-1 in EN 13450.
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.QWURODBestimmung der Konformität von Gesteinskörnungen - Werkseigene ProduktionskontrolleÉvaluation de la conformité des granulats - Contrôle de la production en usineEvaluation of conformity of aggregates - Initial Type Testing and Factory Production Control91.100.15Mineralni materiali in izdelkiMineral materials and productsICS:Ta slovenski standard je istoveten z:EN 16236:2013SIST EN 16236:2013en,de01-september-2013SIST EN 16236:2013SLOVENSKI
STANDARD
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 16236
May 2013 ICS 91.100.15 English Version
Evaluation of conformity of aggregates - Initial Type Testing and Factory Production Control
Évaluation de la conformité des granulats - Contrôle de la production en usine
Bewertung der Konformität von Gesteinskörnungen - Erstprüfung und werkseigene Produktionskontrolle This European Standard was approved by CEN on 5 February 2013.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2013 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 16236:2013: ESIST EN 16236:2013
This standard has been compiled from the ITT and FPC clauses, annexes and tables previously found in the aggregate product standards. It does not introduce any new requirements compared with the original, 2002 versions of those standards. A new, separate Evaluation of Conformity standard is currently in preparation, which will provide more detailed ITT procedures and clear, detailed requirements for product conformity (e.g. statistical conformity criteria, number of samples, tolerances, time limits of validity etc). For the time being, when assessing aggregates within a system of factory production control, at least 90% of gradings taken on different batches within a maximum period of 6 months should fall within the limits specified in the product standards for tolerances on suppliers’ typical declared gradings. The initial type testing and factory production control procedures are designed to be applied to European Standards for aggregates. When the appropriate "conformity" clauses are applied, it forms part of the system for attestation of conformity as required by the Construction Products Directive. It provides the minimum level of ITT and FPC for CE Marking. The testing procedures, using the reference test methods, have the function of providing assurance that a particular aggregate product complies with each of the selected specified requirements in the product standard. The type testing procedure is designed to be applied to all harmonised elements of European Harmonised Standards for aggregates. The system can also be extended to non-harmonised elements. The factory production control system describes control of the sourcing and processing of the aggregate combined with routine sampling and testing to provide ongoing assurance that the aggregates product continues to conform to those properties determined through ITT. Testing within FPC may use either the standard reference tests called up by the aggregate product standards or other test procedures which have been shown to correlate with those tests. For commercial and/or contractual reasons, the manufacturer can choose to perform more testing and inspection than the minimum specified. SIST EN 16236:2013
The assignment of tasks to the notified body and the manufacturer is shown in Annex ZA, Table ZA.3 of EN 12620:2013, EN 13043:2013, EN 13242:2013, EN 13139:2013, EN 13383-1:2013 and EN 13450:2013. 5 Initial type tests The aggregates shall be subject to initial type tests relevant to the intended end use to show conformity with the relevant product standard in the following circumstances: a) a new source of aggregates is to be used; b) there is a major change in the nature of the raw materials or in the processing conditions that may affect the properties of the aggregates. All samples used for initial type testing shall be rep
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.