EN 16236:2018
(Main)Assessment and Verification of the Constancy of Performance (AVCP) of aggregates - Type testing and Factory Production Control
Assessment and Verification of the Constancy of Performance (AVCP) of aggregates - Type testing and Factory Production Control
This European Standard specifies both type testing and factory production control procedures for use during the assessment and verification of constancy of performance of aggregates.
Additional testing carried out within contracts is beyond the scope of this standard.
This European Standard is applicable to European Standards for aggregates if regulatory marking of conformity is to be applied. It is also applicable to European Standards for aggregates where regulatory marking does not apply.
This European Standard is applicable to the type testing and factory production control of aggregates within the scope of EN 12620, EN 13043, EN 13242, EN 13139, EN 13383 1 and EN 13450.
Bewertung und Überprüfung der Leistungsbeständigkeit (AVCP) von Gesteinskörnungen - Typprüfung und werkseigene Produktionskontrolle
Diese Europäische Norm legt die Anforderungen an die Typprüfung und die werkseigene Produktions-kontrolle zur Bewertung und Überprüfung der Leistungsbeständigkeit von Gesteinskörnungen fest.
Vertraglich bedingte, zusätzlich ausgeführte Prüfungen fallen nicht unter den Anwendungsbereich dieser Norm.
Diese Europäische Norm kommt bei Europäischen Normen für Gesteinskörnungen zur Anwendung, wenn regulatorisch eine Kennzeichnung der Konformität gefordert wird. Sie ist auch bei Europäischen Normen in Fällen anwendbar, in denen eine solche Kennzeichnung nicht regulatorisch ist.
Diese Europäische Norm ist auf die Überwachung von Gesteinskörnungen im Rahmen des Anwendungsbereichs von EN 12620, EN 13043, EN 13242, EN 13139, EN 13383-1 und EN 13450 anwendbar.
Evaluation et Vérification de la Constance des Performances (EVCP) des granulats - Essais de types et Maîtrise de la production en usine
La présente Norme européenne spécifie les procédures relatives aux essais de type et à la maîtrise de la production des granulats applicables lors de d’Evaluation et de la Vérification de la Constance des Performances des granulats.
Les essais supplémentaires réalisés dans le cadre de contrats ne font pas partie du domaine d’application de la présente norme.
La présente Norme européenne s’applique aux Normes européennes relatives aux granulats lorsqu’il est prévu d’apposer un marquage réglementaire de conformité. Elle s’applique également aux Normes européennes pour les granulats où le marquage réglementaire n’est pas apposé.
La présente Norme européenne est applicable pour les essais de type et la maîtrise de la production des granulats faisant partie du domaine d’application de l’EN 12620, l’EN 13043, l’EN 13242, l’EN 13139, l’EN 13383-1 et de l’EN 13450.
Ocenjevanje ter preverjanje nespremenljivosti lastnosti (AVCP) agregatov - Preskušanje tipa in kontrola proizvodnje v obratu
Ta evropski standard določa zahteve za preskušanje tipa ter kontrolo proizvodnje v obratu, ki se uporabljajo pri ocenjevanju in preverjanju nespremenljivosti lastnosti agregatov.
Dodatno preskušanje po pogodbah ne spada na področje uporabe tega standarda.
Ta evropski standard se uporablja v evropskih standardih za agregate, če se uporablja ureditveno označevanje skladnosti. Uporablja se tudi v evropskih standardih za agregate, v katerih se ureditveno označevanje ne uporablja.
Ta evropski standard se uporablja za nadzor agregatov, ki spadajo na področje uporabe standardov EN 12620, EN 13043, EN 13242, EN 13139, EN 13383-1 in EN 13450.
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Ocenjevanje ter preverjanje nespremenljivosti lastnosti (AVCP) agregatov - Preskušanje tipa in kontrola proizvodnje v obratuBewertung der Konformität von Gesteinskörnungen - Erstprüfung und werkseigene ProduktionskontrolleEvaluation et Vérification de la Constance des Performances (EVCP) des granulats - Essais de types et Maîtrise de la production en usineAssessment and Verification of the Constancy of Performance (AVCP) of aggregates - Type testing and Factory Production Control91.100.15Mineralni materiali in izdelkiMineral materials and productsICS:Ta slovenski standard je istoveten z:EN 16236:2018SIST EN 16236:2018en,fr,de01-oktober-2018SIST EN 16236:2018SLOVENSKI
STANDARDSIST EN 16236:20131DGRPHãþD
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 16236
July
t r s z ICS
{ sä s r rä s w English Version
Assessment and Verification of the Constancy of egates æ Type testing and Factory Production Control Evaluation et Vérification de la Constance des Maîtrise de la production en usine
Bewertung der Konformität von Gesteinskörnungen æ Erstprüfung und werkseigene Produktionskontrolle This European Standard was approved by CEN on
t v April
t r s yä
egulations which stipulate the conditions for giving this European Standard the status of a national standard without any alterationä Upætoædate lists and bibliographical references concerning such national standards may be obtained on application to the CENæCENELEC Management Centre or to any CEN memberä
translation under the responsibility of a CEN member into its own language and notified to the CENæCENELEC Management Centre has the same status as the official versionsä
CEN members are the national standards bodies of Austriaá Belgiumá Bulgariaá Croatiaá Cyprusá Czech Republicá Denmarká Estoniaá Finlandá Former Yugoslav Republic of Macedoniaá Franceá Germanyá Greeceá Hungaryá Icelandá Irelandá Italyá Latviaá Lithuaniaá Luxembourgá Maltaá Netherlandsá Norwayá Polandá Portugalá Romaniaá Serbiaá Slovakiaá Sloveniaá Spainá Swedená Switzerlandá Turkey and United Kingdomä
EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Rue de la Science 23,
B-1040 Brussels
t r s z CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Membersä Refä Noä EN
s x t u xã t r s z ESIST EN 16236:2018
2 Contents Page European foreword . 3 Introduction . 4 1 Scope . 5 2 Normative references . 5 3 Terms and definitions . 7 4 Assessment and Verification of Constancy of Performance - AVCP . 9 4.1 General . 9 4.2 Type testing . 9 4.2.1 General . 9 4.2.2 Test samples, testing and conformity criteria . 9 4.2.3 Test reports . 10 4.2.4 Shared other party results . 10 4.3 Factory Production Control (FPC) . 10 4.3.1 General . 10 4.3.2 Procedure. 11 4.3.3 Product specific FPC . 15 4.3.4 Initial inspection of production unit and of FPC . 16 4.3.5 Continuous surveillance of FPC . 16 4.3.6 Procedure for modifications . 17 5 Minimum test frequencies and conformity criteria . 17 Bibliography . 34
4 Introduction This European Standard has been written as the system for the Assessment and Verification of the Constancy of Performance (AVCP) of aggregates. This European Standard is intended for use with future revisions (currently in preparation) of the standards listed below. It is not for use with the versions of these standards dated 2002 (plus amendment A1). It is intended to be used in conjunction with the future aggregate product standards: EN 12620, EN 13043, EN 13139, EN 13242, EN 13383-1 and EN 13450 and will be called up by these standards. This European Standard and the corresponding product standards have been written under the Construction Products Regulation (CPR). According to Annex ZA of these standards, the tasks relative to AVCP for the manufacturer comprise Type Testing (TT) and Factory Production Control (FPC). This standard has been compiled from the TT and FPC clauses, annexes and tables previously found in the aggregate product standards. A further revision of this standard is currently under preparation, which will provide more detailed TT procedures and clear, detailed procedures for product conformity (e.g. statistical conformity criteria, number of samples, tolerances, time limits of validity, etc). The type testing and factory production control procedures are designed to be applied to European Standards for aggregates. When the appropriate “conformity” clauses are applied, it forms part of the system of assessment and verification of constancy of performance as required by the Construction Products Regulation. It provides the minimum provisions for TT and FPC for CE Marking. The testing procedures, using the reference test methods, have the function of providing assurance that a particular aggregate product conforms to each of the selected specified characteristics in the product standard. The type testing procedure is designed to be applied to all harmonized elements of European Harmonized Standards for aggregates. The factory production control system describes control of the sourcing and processing of the aggregate combined with routine sampling and testing to provide ongoing assurance that the aggregates product continues to conform to those characteristics determined through TT. Testing within FPC may use either the standard reference tests called up by the aggregate product standards or other test procedures which have been shown to correlate with those tests. For commercial and/or contractual reasons, the manufacturer can choose to perform more testing and inspection than the minimum specified. SIST EN 16236:2018
6 EN 933-9, Tests for geometrical properties of aggregates — Part 9: Assessment of fines — Methylene blue test EN 933-10, Tests for geometrical properties of aggregates — Part 10: Assessment of fines — Grading of filler aggregates (air jet sieving) EN 933-11, Tests for geometrical properties of aggregates — Part 11: Classification test for the constituents of coarse recycled aggregate EN 1097-1, Tests for mechanical and physical properties of aggregates — Part 1: Determination of the resistance to wear (micro-Deval) EN 1097-2, Tests for mechanical and physical properties of aggregates — Part 2: Methods for the determination of resistance to fragmentation
EN 1097-3:1998, Tests for mechanical and physical properties of aggregates — Part 3: Determination of loose bulk density and voids EN 1097-4, Tests for mechanical and physical properties of aggregates — Part 4: Determination of the voids of dry compacted filler EN 1097-5, Tests for mechanical and physical properties of aggregates — Part 5: Determination of the water content by drying in a ventilated oven EN 1097-6, Tests for mechanical and physical properties of aggregates — Part 6: Determination of particle density and water absorption EN 1097-7, Tests for mechanical and physical properties of aggregates — Part 7: Determination of the particle density of filler — Pyknometer method EN 1097-8:2009, Tests for mechanical and physical properties of aggregates — Part 8: Determination of the polished stone value EN 1097-9, Tests for mechanical and physical properties of aggregates — Part 9: Determination of the resistance to wear by abrasion from studded tyres — Nordic test EN 1097-10, Tests for mechanical and physical properties of aggregates — Part 10: Determination of water suction height EN 1367-1, Tests for thermal and weathering properties of aggregates — Part 1: Determination of resistance to freezing and thawing EN 1367-2, Tests for thermal and weathering properties of aggregates — Part 2: Magnesium sulfate test EN 1367-3, Tests for thermal and weathering properties of aggregates
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.