EN ISO 9513:2002
(Main)Metallic materials - calibration of extensometers used in uniaxial testing (ISO 9513:1999)
Metallic materials - calibration of extensometers used in uniaxial testing (ISO 9513:1999)
Specification of a method for the static calibration of extensometers used in uniaxial testing.
Metallische Werkstoffe - Kalibrierung von Längenänderungs-Messeinrichtungen für die Prüfung mit einachsiger Beanspruchung (ISO 9513:1999)
In dieser Internationalen Norm ist ein Verfahren für die statische Kalibrierung von Längenänderungs-Messeinrichtungen, die bei Prüfung mit einachsiger Beanspruchung verwendet werden, festgelegt.
Unter "Längenänderungs-Messeinrichtung" versteht man den Wegaufnehmer und die zugehörige Anzeige- oder Registriereinrichtung.
ANMERKUNG Diese Internationale Norm gibt keine detaillierten Anleitungen zur Kalibrierung von Längenänderungs-Messeinrichtungen mit:
veränderlichen Anfangs-Gerätemesslängen;
berührungsloser Messung;
Ganzfeldmessverfahren.
Für solche Messeinrichtungen sollten besondere Maßnahmen getroffen und bei der nächsten Überarbeitung dieser Internationalen Norm berücksichtigt werden. Einige Hinweise für solche Messeinrichtungen kann man in ASTM E83:1996 finden (siehe Literaturhinweise).
Matériaux métalliques - Etalonnage des extensomètres utilisés lors d'essais unaxiaux (ISO 9513:1999)
Kovinski materiali - Kalibracija ekstenzometrov, ki se uporabljajo pri enoosnem preskušanju (ISO 9513:1999)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-marec-2004
1DGRPHãþD
SIST EN 10002-4:1997
Kovinski materiali - Kalibracija ekstenzometrov, ki se uporabljajo pri enoosnem
preskušanju (ISO 9513:1999)
Metallic materials - calibration of extensometers used in uniaxial testing (ISO 9513:1999)
Metallische Werkstoffe - Kalibrierung von Längenänderungs-Messeinrichtungen für die
Prüfung mit einachsiger Beanspruchung (ISO 9513:1999)
Matériaux métalliques - Etalonnage des extensometres utilisés lors d'essais unaxiaux
(ISO 9513:1999)
Ta slovenski standard je istoveten z: EN ISO 9513:2002
ICS:
77.040.10 Mehansko preskušanje kovin Mechanical testing of metals
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN ISO 9513
NORME EUROPÉENNE
EUROPÄISCHE NORM
September 2002
ICS 77.040.10 Supersedes EN 10002-4:1994
English version
Metallic materials - calibration of extensometers used in uniaxial
testing (ISO 9513:1999)
Matériaux métalliques – Etalonnage des extensomètres
utilisés lors d’essais unaxiaux (ISO 9513:1999)
This European Standard was approved by CEN on 14 July 2002.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,
Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2002 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 9513:2002 E
worldwide for CEN national Members.
Foreword
The text of ISO 9513:1999 has been prepared by Technical Committee ISO/TC 164
"Mechanical testing of metals” of the International Organization for Standardization (ISO) and
has been taken over as EN ISO 9513:2002 by Technical Committee ECISS/TC 1 "Steels -
Mechanical and physical tests", the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication
of an identical text or by endorsement, at the latest by March 2003, and conflicting national
standards shall be withdrawn at the latest by March 2003.
This document supersedes EN 10002-4:1994.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium,
Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy,
Luxembourg, Malta, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the
United Kingdom.
Endorsement notice
The text of the International Standard ISO 9513:1999 has been approved by CEN as a
European Standard without any modifications.
INTERNATIONAL ISO
STANDARD 9513
Second edition
1999-04-15
Corrected and reprinted
2001-02-01
Metallic materials — Calibration of
extensometers used in uniaxial testing
Matériaux métalliques — Étalonnage des extensomètres utilisés lors
d'essais unaxiaux
A
Reference number
ISO 9513:1999(E)
ISO 9513:1999(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not
be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading
this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in
this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the
unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 1999
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic
or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body
in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.ch
Web www.iso.ch
Printed in Switzerland
ii
© ISO
ISO 9513:1999(E)
Contents Page
1 Scope . 1
2 Symbols and designations . 1
3 Principle. 2
4 Calibration apparatus. 2
5 Procedure . 2
5.1 Position of the extensometer . 2
5.2 Temperature at which the calibration is made . 2
5.3 Accuracy of gauge length of the extensometer . 2
5.4 Range of calibration . 3
5.5 Calibration procedure . 3
5.6 Determination of the characteristics of the extensometer. 3
6 Classification of the extensometer . 3
7 Frequency of calibration. 4
8 Calibration report. 5
Annex A (informative) Example of calibration ranges of an extensometer. 6
(informative)
Annex B Parameters for classification of an extensometer. 7
Bibliography. 10
iii
© ISO
ISO 9513:1999(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO
member bodies). The work of preparing International Standards is normally carried out through ISO technical
committees. Each member body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, governmental and non-governmental, in
liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical
Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3.
Draft International Standards adopted by the technical committees are circulated to the member bodies for voting.
Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.
International Standard ISO 9513 was prepared by Technical Committee ISO/TC 164, Mechanical testing of metals,
Subcommittee SC 1, Uniaxial testing.
This second edition cancels and replaces the first edition (ISO 9513:1989) which has been technically revised.
This corrected and reprinted version incorporates the changes specified in ISO 9513:1999/Cor.1:2000 (E), which is
hereby cancelled and replaced, together with an additional change to Table 2, row 4, column 3.
Annexes A and B of this International Standard are for information only.
iv
INTERNATIONAL STANDARD © ISO ISO 9513:1999(E)
Metallic materials — Calibration of extensometers used in uniaxial
testing
1 Scope
This International Standard specifies a method for the static calibration of extensometers used in uniaxial testing.
The term "extensometer" is understood to mean the displacement measuring device and the system for indicating
or recording this displacement.
NOTE This International Standard does not at present provide detailed guidance on the calibration of those types of
extensometer which have:
variable gauge lengths;
no contact with the test piece;
full field strain measurements devices.
Special consideration should be given to such devices. T
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.