EN ISO 24395:2023
(Main)Dentistry - Classification of tooth restorations preparation (ISO 24395:2023)
Dentistry - Classification of tooth restorations preparation (ISO 24395:2023)
This document establishes a system for classifying the location and depth of human tooth restorations preparations.
Zahnheilkunde - Einteilung von Zahnrestaurationspräparationen (ISO 24395:2023)
Dieses Dokument legt ein System zur Klassifizierung der Lage und Tiefe von Präparationen für Zahnrestaurationen beim Menschen fest.
Médecine bucco-dentaire - Classification de la préparation des restaurations dentaires (ISO 24395:2023)
Le présent document établit un système pour la classification de l’emplacement et de la profondeur des préparations en vue de restaurations de dents humaines.
Zobozdravstvo - Klasifikacija restavracij preparacij (ISO/FDIS 24395:2023)
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
oSIST prEN ISO 24395:2022
01-november-2022
Zobozdravstvo - Klasifikacija restavracij preparacij (ISO/DIS 24395:2022)
Dentistry - Classification of tooth restorations preparation (ISO/DIS 24395:2022)
Zahnheilkunde - Kavitätenklassifikation für Zahnrestaurationen (ISO/DIS 24395:2022)
Médecine bucco-dentaire - Classification de la préparation des restaurations dentaires
(ISO/DIS 24395:2022)
Ta slovenski standard je istoveten z: prEN ISO 24395
ICS:
11.060.01 Zobozdravstvo na splošno Dentistry in general
oSIST prEN ISO 24395:2022 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN ISO 24395:2022
---------------------- Page: 2 ----------------------
oSIST prEN ISO 24395:2022
DRAFT INTERNATIONAL STANDARD
ISO/DIS 24395
ISO/TC 106/SC 3 Secretariat: AFNOR
Voting begins on: Voting terminates on:
2022-09-08 2022-12-01
Dentistry — Classification of tooth restorations
preparation
ICS: 11.060.01
This document is circulated as received from the committee secretariat.
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
ISO/CEN PARALLEL PROCESSING
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 24395:2022(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION. © ISO 2022
---------------------- Page: 3 ----------------------
oSIST prEN ISO 24395:2022
ISO/DIS 24395:2022(E)
DRAFT INTERNATIONAL STANDARD
ISO/DIS 24395
ISO/TC 106/SC 3 Secretariat: AFNOR
Voting begins on: Voting terminates on:
Dentistry — Classification of tooth restorations
preparation
ICS: 11.060.01
This document is circulated as received from the committee secretariat.
COPYRIGHT PROTECTED DOCUMENT
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
© ISO 2022
ISO/CEN PARALLEL PROCESSING
THEREFORE SUBJECT TO CHANGE AND MAY
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
NOT BE REFERRED TO AS AN INTERNATIONAL
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on STANDARD UNTIL PUBLISHED AS SUCH.
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
IN ADDITION TO THEIR EVALUATION AS
or ISO’s member body in the country of the requester. BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
ISO copyright office
USER PURPOSES, DRAFT INTERNATIONAL
CP 401 • Ch. de Blandonnet 8
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
CH-1214 Vernier, Geneva
POTENTIAL TO BECOME STANDARDS TO
Phone: +41 22 749 01 11
WHICH REFERENCE MAY BE MADE IN
Reference number
Email: copyright@iso.org
NATIONAL REGULATIONS.
Website: www.iso.org ISO/DIS 24395:2022(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
Published in Switzerland
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
ii
© ISO 2022 – All rights reserved
PROVIDE SUPPORTING DOCUMENTATION. © ISO 2022
---------------------- Page: 4 ----------------------
oSIST prEN ISO 24395:2022
ISO/DIS 24395:2022(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Classification . 1
4.1 Location of preparation . 1
4.2 Depth of tooth restoration preparations . 2
5 Recommendations . 2
Bibliography . 3
iii
© ISO 2022 – All rights reserved
---------------------- Page: 5 ----------------------
oSIST prEN ISO 24395:2022
ISO/DIS 24395:2022(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an en
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.