EN 12629-2:2002+A1:2010
(Main)Machines for the manufacture of constructional products from concrete and calcium-silicate - Safety - Part 2: Block making machines
Machines for the manufacture of constructional products from concrete and calcium-silicate - Safety - Part 2: Block making machines
This part of EN 12629, taken together with EN 12629-1:2000+A1, applies to machines for the manufacture of blocks, kerbs, paving stones and similar concrete products.
EN 12629-1:2000+A1 specifies general requirements applicable to machines for the manufacture of constructional products from concrete and calcium silicate.
This document specifies the additional requirements to and/or the deviations from EN 12629-1:2000+A1 specific to the machines it covers.
1.2 This European Standard deals with all significant hazards pertinent to these machines, when they are used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer (see Clause 4). This European Standard specifies the appropriate technical measures to eliminate or reduce risks arising from the significant hazards.
1.3 This European Standard applies to the machines from the point at which the mixture enters the machine (see point 1-2 of annex B) and the point where the pallet boards are brought to the assembly (see point 3 of annex B) until the point where the green products are removed from the machine assembly to the curing system (see point 4 of annex B).
1.4 This European Standard deals with the hazards listed in clause 4 which can arise during the operation and maintenance, including the interfaces, of the block making machines, when carried out in accordance with the specifications given by the manufacturer or his authorised representative.
NOTE 1 Amendment is under preparation to deal with noise, in particular for measures to reduce noise at source and a noise test code including noise declaration.
NOTE 2 Interfaces between the block making machines and others of the installation are dealt with in
EN 12629-1:2000+A1:2010 (7.2).
This standard establishes safety requirements and/or methods of protection which apply to these machines.
Maschinen für die Herstellung von Bauprodukten aus Beton und Kalksandsteinmassen - Sicherheit - Teil 2: Steinformmaschinen
Dieser Teil von EN 12629, zusammen mit EN 12629-1:2000+A1:2010, gilt für Maschinen zur
Herstellung von Blöcken, Bordsteinen, Pflastersteinen und ähnlichen Betonprodukten.
EN 12629-1:2000+A1:2010 spezifiziert allgemeine Anforderungen für Maschinen zur Herstellung von Bauprodukten
aus Beton und Kalksandstein.
Dieses Dokument legt die zusätzlichen Anforderungen für und/oder Abweichungen von
EN 12629-1:2000+A1:2010, die spezifisch für die Maschinen sind, die es abdeckt, fest."
1.2 !Diese Europäische Norm behandelt alle signifikanten Gefährdungen, die auf diese Maschinen
zutreffen, wenn sie bestimmungsgemäß und unter den Bedingungen des Missbrauchs, die vernünftigerweise
vom Hersteller vorhersehbar sind, verwendet werden (siehe Abschnitt 4). Diese Europäische Norm spezifiziert
die entsprechenden technischen Maßnahmen zur Beseitigung oder Verminderung der Risiken, die von den
signifikanten Gefährdungen ausgehen."
1.3 Diese Norm gilt für die Maschine von der Stelle an, wo die Mischzufuhr die Maschine befüllt (siehe
Punkt 1 bis 2 von Anhang B) und an der Stelle, wo die Unterlagsbretter zugeführt werden (siehe Punkt 3 von
Anhang B) bis zu der Stelle, wo die Frischprodukte zu dem „Trockenkammer-System“ (siehe Punkt 4 von
Anhang B) abtransportiert werden.
Machines pour la fabrication de produits de construction en béton et silico-calcaire - Sécurité - Partie 2: Machines à blocs
La présente partie de l’EN 12629, utilisée avec l’EN 12629-1:2000+A1, s’applique aux machines pour la
fabrication de blocs, bordures de trottoirs, pavés et autres produits similaires en béton.
L’EN 12629-1:2000+A1 spécifie les prescriptions générales applicables aux machines pour la fabrication de produits
de construction en béton et silico-calcaire.
Le présent document spécifie les prescriptions supplémentaires et les dérogations à l’EN 12629-1:2000+A1
spécifiques aux machines concernées."
1.2 !La présente Norme européenne traite tous les phénomènes dangereux significatifs spécifiques
à ces machines, lorsque celles-ci sont utilisées normalement et dans des conditions de mauvais usage que le
fabricant peut raisonnablement prévoir (voir l’Article 4). Cette Norme européenne spécifie les mesures techniques
appropriées pour éliminer ou réduire les risques dus aux phénomènes dangereux significatifs."
1.3 La présente Norme européenne s’applique aux machines, du point où le mélange pénètre dans la machine
(voir points 1 et 2 de l’annexe B) et du point où les palettes sont introduites dans la machine (voir point 3 de
l’annexe B) jusqu’au point où les produits frais sont transférés de la machine au système de cure (voir point 4 de
l’annexe B).
Stroji za izdelavo gradbenih proizvodov iz betona in apnenega peščenca - Varnost - 2. del: Stroji za izdelavo blokov
Ta del EN 12629 skupaj z EN 12629-1:2000+A1:2010 velja za stroje za izdelavo blokov, robnikov, tlakovcev in podobnih proizvodov iz betona. EN 12629-1:2000+A1:2010 določa splošne zahteve, ki veljajo za stroje za izdelavo gradbenih proizvodov iz betona in apnenega peščenca. Ta dokument določa dodatne zahteve in/ali odstopanja od EN 12629-1:2000+A1:2010, specifične za stroje, ki jih zajema. Ta evropski standard obravnava vse pomembne nevarnosti, nevarne situacije in primere, ki se nanašajo na te stroje, kadar se uporabljajo kot predvideno in pod pogoji napačne uporabe, ki jih razumno predvidi proizvajalec (glej Klavzulo 4). Ta evropski standard določa primerne tehnične ukrepe za odpravo ali zmanjšanje tveganj, ki se pojavijo zaradi pomembnih nevarnosti. Ta evropski standard velja za stroje od točke, na kateri zmes vstopa v stroj (glej točki 1 in 2 Dodatka B) in točke, na kateri paletne plošče prihajajo v montažo (glej točko 3 Dodatka B), do točke, na kateri gredo zeleni proizvodi iz strojnega sklopa v sušilni sistem (glej točko 4 Dodatka B). Ta evropski standard obravnava nevarnosti, navedene v Klavzuli 4, do katerih lahko pride med obratovanjem in vzdrževanjem strojev za izdelavo blokov, vključno z vmesniki, kadar se izvajata v skladu s specifikacijami, ki jih je navedel proizvajalec ali njegov pooblaščeni zastopnik. Ta standard vzpostavlja varnostne zahteve in/ali zaščitne metode, ki veljajo za te stroje.
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Maschinen für die Herstellung von Bauprodukten aus Beton und Kalksandsteinmassen - Sicherheit - Teil 2: SteinformmaschinenMachines pour la fabrication de produits de construction en béton et silico-calcaire - Sécurité - Partie 2: Machines à blocsMachines for the manufacture of constructional products from concrete and calcium-silicate - Safety - Part 2: Block making machines91.220Gradbena opremaConstruction equipmentICS:Ta slovenski standard je istoveten z:EN 12629-2:2002+A1:2010SIST EN 12629-2:2004+A1:2010en,fr01-december-2010SIST EN 12629-2:2004+A1:2010SLOVENSKI
STANDARD
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 12629-2:2002+A1
September 2010 ICS 91.220 Supersedes EN 12629-2:2002English Version
Machines for the manufacture of constructional products from concrete and calcium-silicate - Safety - Part 2: Block making machines
Machines pour la fabrication de produits de construction en béton et silico-calcaire - Sécurité - Partie 2: Machines à blocs
Maschinen für die Herstellung von Bauprodukten aus Beton und Kalksandsteinmassen - Sicherheit - Teil 2: Steinformmaschinen This European Standard was approved by CEN on 1 November 2002 and includes Amendment 1 approved by CEN on 5 August 2010.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2010 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 12629-2:2002+A1:2010: ESIST EN 12629-2:2004+A1:2010
Mechanical hazards zones for a common block making machine and requirements and measures . 11Annex B (informative)
Terminology of a common block making machine . 12Annex ZA (informative)
!!!! Relationship between this European Standard and the Essential Requirements of EU Directive 2006/42/EC"""" . 13Bibliography . 14
March 2011. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. This document includes Amendment 1, approved by CEN on 2010-08-05. This document supersedes EN 12629-2:2002. The start and finish of text introduced or altered by amendment is indicated in the text by tags ! ". !This European Standard has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EU Directive(s). For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this document." !The series "Machines for the manufacture of constructional products from concrete and calcium – silicate – Safety" consists of the following parts: Part 1: Common requirements Part 2: Block making machines Part 3: Slide and turntable machines Part 4: Concrete roof tile making machines Part 5.1: Pipe making machines manufacturing in the vertical axis Part 5.2: Pipe making machines manufacturing in the horizontal axis Part 5.3: Pipe prestressing machines Part 5.4: Concrete pipe coating machines Part 6: Stationary and mobile equipment for the manufacture of precast reinforced products Part 7: Stationary and mobile equipment for long line manufacture of prestressed products Part 8: Machines and equipment for the manufacture of constructional products from calcium silicate (and concrete)" !deleted text" According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. SIST EN 12629-2:2004+A1:2010
When provisions of this type C document are different from those, which are stated in type A or B documents, the provisions of this type C document take precedence over the provisions of the other documents, for machines that have been designed and built according to the provisions of this type C document.
This document specifies the additional requirements to and/or the deviations from EN 12629-1:2000+A1:2010 specific for the block making machines as described in 1.1. With the aim of clarifying the intentions of the document it should be noticed that the following assumptions were made when producing it: specific conditions of use or environmental conditions out of the scope of the document shall be the subject of negotiations between the manufacturer and the user/owner, the equipment will only be used by competent and designated persons,
the place of use/installation is adequately lit,
all operations are carried out by specially trained operators."
1 Scope 1.1 !This part of EN 12629, taken together with EN 12629-1:2000+A1:2010, applies to machines for the manufacture of blocks, kerbs, paving stones and similar concrete products.
EN 12629-1:2000+A1:2010 specifies general requirements applicable to machines for the manufacture of constructional products from concrete and calcium–silicate.
This document specifies the additional requirements to and/or the deviations from EN 12629-1:2000+A1:2010 specific to the machines it covers." 1.2 !This European Standard deals with all significant hazards pertinent to these machines, when they are used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer (see Clause 4). This European Standard specifies the appropriate technical measures to eliminate or reduce risks arising from the significant hazards." 1.3 This European Standard applies to the machines from the point at which the mixture enters the machine (see point 1-2 of annex B) and the point where the pallet boards are brought to the assembly (see point 3 of annex B) until the point where the green products are removed from the machine assembly to the curing system (see point 4 of annex B). !deleted text" SIST EN 12629-2:2004+A1:2010
!EN 12629-1:2000+A1:2010 (7.2)". This standard establishes safety requirements and/or methods of protection which apply to these machines. ! 1.5 This document is not applicable to block making machines, which are manufactured before the date of publication of this document by CEN." 2 Normative references !The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies." !deleted text" !EN 12629-1:2000+A1:2010", Machines for the manufacture of constructional products from concrete and calcium-silicate — Safety — Part 1: Common requirements !EN ISO 12100-1:2003, Safety of machinery — Basic concepts, general principles for design — Part 1: Basic terminology, methodology (ISO 12100-1:2003) EN ISO 12100-1:2003, Safety of machinery — Basic concepts, general principles for design — Part 2: Technical principles (ISO 12100-2:2003)" 3 Terms and definitions !For the purposes of this document, the terms and definitions given in EN ISO 12100-1:2003,
EN 12629-1:2000+A1:2010 and the following apply." NOTE See also annex B for terminology of a typical block making machine. 3.1 drawing box container having the shape of a box with an open or movable bottom. The drawing box fills the mould with the mixture 3.2 drawing box grid machine element which is placed at the bottom of the drawing box. It consists of bars specially designed so as to assist a uniform supply of fresh concrete into the mould. The grid can be loose, fixed or movable with respect to the drawing box 3.3 feed hopper
device that contains the mixture which is transported to the drawing box by a discharge gate or a dosing belt SIST EN 12629-2:2004+A1:2010
the mould. It is intended to: assist the compacting of concrete by compression; form the upper part of the products. 4 List of significant hazards This clause contains all hazards, as far as they are dealt with in this European Standard, identified by risk assessments significant for this type of machinery and which require action to eliminate or reduce risk. !deleted text" 4.1 Mechanical hazards (see informative annex B) Annex B (informative) illustrates an example of a common machine type. In accordance with !Clause 4 of EN 12629-1:2000+A1:2010" the hazard zones, marked 1-8 at annex A of this standard, are described in the following table (see also 4.1.1 to 4.1.6 for detailed mechanical hazards). SIST EN 12629-2:2004+A1:2010
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.