EN ISO 14585:2001
(Main)Hexalobular socket pan head tapping screws (ISO 14585:2001)
Hexalobular socket pan head tapping screws (ISO 14585:2001)
Flachkopf-Blechschrauben mit Innensechsrund (ISO 14585:2001)
Diese Internationale Norm legt die Eigenschaften von Flachkopf-Blechschrauben mit Innensechsrund, mit Gewinde von ST2,9 bis ST6,3 fest.
Werden in besonderen Fällen andere als in dieser Internationalen Norm aufgeführte Festlegungen benötigt, sollten diese aus bestehenden Internationalen Normen wie zum Beispiel ISO 1478, ISO 2702 und ISO 4759-1 ausge-wählt werden.
Vis à tôle à tête cylindrique bombée large à six lobes internes (ISO 14585:2001)
La présente Norme internationale spécifie les caractéristiques des vis à tôle à tête cylindrique bombée large à six lobes internes, de filetage ST2,9 à ST6,3 inclus. Si, dans des cas particuliers, des spécifications autres que celles figurant dans la présente Norme internationale sont requises, il est recommandé de les choisir dans les Normes internationales existantes, par exemple ISO 1478, ISO 2702, ISO 4759-1.
Notranji šestrogeljnik v polokrogli valjasti glavi pločevinskega vijaka (ISO 14585:2001)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-julij-2002
1RWUDQMLãHVWURJHOMQLNYSRORNURJOLYDOMDVWLJODYLSORþHYLQVNHJDYLMDND ,62
Hexalobular socket pan head tapping screws (ISO 14585:2001)
Flachkopf-Blechschrauben mit Innensechsrund (ISO 14585:2001)
Vis a tôle a tete cylindrique bombée large a six lobes internes (ISO 14585:2001)
Ta slovenski standard je istoveten z: EN ISO 14585:2001
ICS:
21.060.10 Sorniki, vijaki, stebelni vijaki Bolts, screws, studs
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN ISO 14585
NORME EUROPÉENNE
EUROPÄISCHE NORM
September 2001
ICS 21.060.10
English version
Hexalobular socket pan head tapping screws (ISO 14585:2001)
Vis à tôle à tête cylindrique bombée large à six lobes Flachkopf-Blechschrauben mit Innensechsrund (ISO
internes (ISO 14585:2001) 14585:2001)
This European Standard was approved by CEN on 1 September 2001.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,
Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2001 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 14585:2001 E
worldwide for CEN national Members.
CORRECTED 2002-02-06
Foreword
This document (ISO 14585:2001) has been prepared by Technical Committee ISO/TC 2
"Fasteners" in collaboration with Technical Committee CEN/TC 185 "Threaded and non-
threaded mechanical fasteners and accessories", the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of
an identical text or by endorsement, at the latest by March 2002, and conflicting national
standards shall be withdrawn at the latest by March 2002.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium, Czech
Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg,
Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of the International Standard ISO 14585:2001 has been approved by CEN as a
European Standard without any modifications.
NOTE Normative references to International Standards are listed in annex ZA (normative).
Annex ZA
(normative)
Normative references to international publications
with their relevant European publications
This European Standard incorporates by dated or undated reference, provisions from other
publications. These normative references are cited at the appropriate places in the text and the
publications are listed hereafter. For dated references, subsequent amendments to or revisions of
any of these publications apply to this European Standard only when incorporated in it by
amendment or revision. For undated references the latest edition of the publication referred to
applies (including amendments).
NOTE Where an International Publication has been modified by common modifications, indicated
by (mod.), the relevant EN/HD applies.
Publication Year Title EN Year
ISO 1478 1999 Tapping screws thread EN ISO 1478 1999
ISO 2702 1992 Heat-treated steel tapping EN ISO 2702 1994
screws — Mechanical properties
ISO 3269 2000 Fasteners — Acceptance EN ISO 3269 2000
inspection
ISO 4042 1999 Fasteners — Electroplated EN ISO 4042 1999
coatings
ISO 4759-1 2000 Tolerances for fasteners — EN ISO 4759-1 2000
Part 1: Bolts, screws, studs and
nuts — Product grades A, B and
C
ISO 10664 1999 Hexalobular internal driving EN ISO 10664 1999
feature for bolts and screws
ISO 225 1983 Fasteners - Bolts, screws, studs EN 20225 1991
and nuts - Symbols and
designations of dimensions
INTERNATIONAL ISO
STANDARD 14585
First edition
2001-09-01
Hexalobular socket pan head tapping
screws
Vis à tôle à tête cylindrique bombée large à six lobes internes
Reference number
ISO 14585:2001(E)
©
ISO 2001
ISO 14585:2001(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not
be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this
file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this
area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters
were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event
that a problem relating to it is found, please inform the Centra
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.