EN ISO 17172:2021
(Main)Fine ceramics (advanced ceramics, advanced technical ceramics) - Determination of compaction properties of ceramic powders (ISO 17172:2014)
Fine ceramics (advanced ceramics, advanced technical ceramics) - Determination of compaction properties of ceramic powders (ISO 17172:2014)
ISO 17172:2014 specifies the test method for determining the extent to which granulated or ungranulated ceramic powders are compacted, when subjected to uniaxial compressive loading in a confining die, under specified conditions.
Hochleistungskeramik - Bestimmung der Verdichtungseigenschaften keramischer Pulver (ISO 17172:2014)
Diese Internationale Norm legt das Prüfverfahren für die Bestimmung des Ausmaßes fest, bis zu dem granulierte oder nicht granulierte keramische Pulver bei uniaxialer Druckbelastung in einer formstabilen Matrize unter festgelegten Bedingungen verdichtet werden.
Céramiques techniques - Détermination des propriétés de compactage des poudres céramiques (ISO 17172:2014)
La présente Norme Internationale spécifie la méthode d'essai pour déterminer dans quelle mesure les poudres céramiques, granulées ou non, sont compactées lorsqu'elles sont soumises à une charge de compression uniaxiale dans une matrice de confinement, dans des conditions spécifiées.
Fina keramika (sodobna keramika, sodobna tehnična keramika) - Ugotavljanje lastnosti za stiskanje keramičnih praškov (ISO 17172:2014)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-marec-2021
Fina keramika (sodobna keramika, sodobna tehnična keramika) - Ugotavljanje
lastnosti za stiskanje keramičnih praškov (ISO 17172:2014)
Fine ceramics (advanced ceramics, advanced technical ceramics) - Determination of
compaction properties of ceramic powders (ISO 17172:2014)
Hochleistungskeramik - Bestimmung der Verdichtungseigenschaften keramischer Pulver
(ISO 17172:2014)
Céramiques techniques - Détermination des propriétés de compactage des poudres
céramiques (ISO 17172:2014)
Ta slovenski standard je istoveten z: EN ISO 17172:2021
ICS:
81.060.30 Sodobna keramika Advanced ceramics
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN ISO 17172
EUROPEAN STANDARD
NORME EUROPÉENNE
January 2021
EUROPÄISCHE NORM
ICS 81.060.30
English Version
Fine ceramics (advanced ceramics, advanced technical
ceramics) - Determination of compaction properties of
ceramic powders (ISO 17172:2014)
Céramiques techniques - Détermination des propriétés Hochleistungskeramik - Bestimmung der
de compactage des poudres céramiques (ISO Verdichtungseigenschaften keramischer Pulver (ISO
17172:2014) 17172:2014)
This European Standard was approved by CEN on 20 December 2020.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 17172:2021 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
European foreword
The text of ISO 17172:2014 has been prepared by Technical Committee ISO/TC 206 "Fine ceramics” of
the International Organization for Standardization (ISO) and has been taken over as EN ISO 17172:2021
by Technical Committee CEN/TC 184 “Advanced technical ceramics” the secretariat of which is held by
DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by July 2021, and conflicting national standards shall be
withdrawn at the latest by July 2021.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 17172:2014 has been approved by CEN as EN ISO 17172:2021 without any modification.
INTERNATIONAL ISO
STANDARD 17172
First edition
2014-02-01
Fine ceramics (advanced ceramics,
advanced technical ceramics) —
Determination of compaction
properties of ceramic powders
Céramiques techniques — Détermination des propriétés de
compactage des poudres céramiques
Reference number
ISO 17172:2014(E)
©
ISO 2014
ISO 17172:2014(E)
© ISO 2014
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2014 – All rights reserved
ISO 17172:2014(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Principle . 1
4 Symbols and designation . 1
5 Apparatus . 1
6 Sampling . 2
7 Procedure. 2
7.1 Quantity . 2
7.2 Cleaning of die and punches . 2
7.3 Powder testing conditions . 2
7.4 Lubrication . 3
7.5 Compaction and ejection . 3
7.6 Compaction pressures . 4
8 Expression of results . 4
8.1 Calculation . 4
8.2 Compaction curve . 4
9 Test report . 4
Bibliography . 8
ISO 17172:2014(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity
assessment, as well as information about ISO’s adherence to the WTO principles in the Technical Barriers
to Trade (TBT) see the following URL: Foreword - Supplementary information
The committee responsible for this document is ISO/TC 206, Fine ceramics.
iv © ISO 2014 – All rights reserved
INTERNATIONAL STANDARD ISO 17172:2014(E)
Fine ceramics (advanced ceramics, advanced technical
ceramics) — Determination of compaction properties of
ceramic powders
1 Scope
This International Standard specifies the test method to determine the extent to which granulated or
ungranulated ceramic powders are compacted, when subjected to uniaxial compressive loading in a
confining die, under specified conditions.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
ISO/IEC 17025, General requirements for the competence of testing and calibration laboratories
3 Principle
Granulated or ungranulated ceramic powders are compacted uniaxially in a confining die by double-
action pressing (mode 1) or by single-action pressing (mode 2). Samples of the ceramic powders can be
pressed either at a single specified pressure or at a series of specified pressures. After ejection from die,
the apparent density of the ceramic powder compact is determined.
The apparent density obtained in the former case represents the compaction properties of the ceramic
powder at the specified pressure. The apparent densities obtained in the latter case are utilized for
drawing the compaction curve of the ceramic powder, which is a plot of apparent density as a function
of compaction pressure.
4 Symbols and designation
Symbol Designation Unit
ρ Apparent density g/cm
a
m Mass of ceramic powder compact g
V Volume of ceramic powder compact cm
If the apparent density is measured at only one specified pressure, for example 100 MPa, the symbol
becomes ρ (100).
a
5 Apparatus
5.1 Cylindrical die, should be made from hard material, preferably hardened steel or tungsten carbide.
The die shall contain two upper and lower punches for producing cylindrical powder compacts and shall
be of the floating type or of the type suspended from a spring (mode 1), or of stationary type with only
one movable upper punch (mode 2). The die shall be capable of making cylindrical powder compacts
with a diameter from 10 mm to 26 mm and a height to diameter ratio between 0,3 and 0,5 (mode 1),
or with a diameter from 10 mm to 32 mm and a height to diameter ratio between 0,15 and 0,25 (mode
ISO 17172:2014(E)
2), as indicated in Figure 1. The upper part of the die shall be preferably designed to avoid d
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.