EN ISO 4157-3:1998
(Main)Construction drawings - Designation systems - Part 3: Room identifiers (ISO 4157-3:1998)
Construction drawings - Designation systems - Part 3: Room identifiers (ISO 4157-3:1998)
This part of ISO 4157 establishes requirements for designation systems for rooms, areas, spaces, and voids in
buildings by room identifiers. It introduces a new designation concept intended for identification of rooms in a project
throughout its life cycle, i.e. the conception, programming, planning, erection, maintenance, remodelling and
demolition phases.
Zeichnungen für das Bauwesen - Bezeichnungssysteme - Teil 3: Raum-Kennzeichnungen (ISO 4157-3:1998)
Dieser Teil der ISO 4157 legt durch Rau-Kennzeichnungen Anforderungen an Bezeichnungssysteme für Räume, Bereiche, Zwischenräume und Hohlräume in Gebäuden fest. Er stellt ein neues Kennzeichnungskonzept for, welches die Erkennung von Räumen in einem Bauvorhaben und seinen durchgängigen Phasen Entwurf, Entwicklung, Planung, Errichtung, Wartung, Umbau und Abriß beabsichtigt.
Dessins de bâtiment - Systèmes de désignation - Partie 3: Identificateurs de pièces (ISO 4157-3:1998)
La présente partie de l'ISO 4157 spécifie les exigences concernant les systèmes de désignation par des
identificateurs de pièces des pièces, zones, espaces et vides dans des bâtiments. Elle introduit un nouveau
concept de désignation destiné à identifier les pièces dans un projet tout au long des phases de conception, de
programmation, d'étude, de construction, de maintenance, de rénovation et de démolition.
Gradbeniške risbe - Sistemi označevanja - 3. del: Identifikatorji prostora (ISO 4157-3:1998)
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
01-februar-2002
*UDGEHQLãNHULVEH6LVWHPLR]QDþHYDQMDGHO,GHQWLILNDWRUMLSURVWRUD,62
Construction drawings - Designation systems - Part 3: Room identifiers (ISO 4157-
3:1998)
Zeichnungen für das Bauwesen - Bezeichnungssysteme - Teil 3: Raum-
Kennzeichnungen (ISO 4157-3:1998)
Dessins de bâtiment - Systemes de désignation - Partie 3: Identificateurs de pieces (ISO
4157-3:1998)
Ta slovenski standard je istoveten z: EN ISO 4157-3:1998
ICS:
01.100.30 *UDGEHQLQDþUWL Construction drawings
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
INTERNATIONAL ISO
STANDARD 4157-3
First edition
1998-12-01
Construction drawings — Designation
systems —
Part 3:
Room identifiers
Dessins de bâtiment — Systèmes de désignation —
Partie 3: Identificateurs de pièces
A
Reference number
ISO 4157-3:1998(E)
ISO 4157-3:1998(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO
member bodies). The work of preparing International Standards is normally carried out through ISO technical
committees. Each member body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, governmental and non-governmental, in
liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical
Commission (IEC) on all matters of electrotechnical standardization.
Draft International Standards adopted by the technical committees are circulated to the member bodies for voting.
Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.
International Standard ISO 4751-3 was prepared by Technical Committee ISO/TC 10, Technical drawings, product
definition and related documentation, Subcommittee SC 8, Construction documentation.
ISO 4157 consists of the following parts, under the general title Construction drawings — Designation systems:
Part 1: Buildings and parts of buildings
Part 2: Room names and numbers
Part 3: Room identifiers
© ISO 1998
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic
or mechanical, including photocopying and microfilm, without permission in writing from the publisher.
International Organization for Standardization
Case postale 56 • CH-1211 Genève 20 • Switzerland
Internet iso@iso.ch
Printed in Switzerland
ii
INTERNATIONAL STANDARD © ISO ISO 4157-3:1998(E)
Construction drawings — Designation systems —
Part 3:
Room identifiers
1 Scope
This part of ISO 4157 establishes requirements for designation systems for rooms, areas, spaces, and voids in
buildings by room identifiers. It introduces a new designation concept intended for identification of rooms in a project
throughout its life cycle, i.e. the conception, programming, planning, erection, maintenance, remodelling and
demolition phases.
2 Normative references
The following standards contain provisions, which through reference in this text, constitute provisions of this part of
ISO 4157. At the time of publication, the editions indicated were valid. All standards are subject to revision, and
parties to agreements based on this part of ISO 4157 are encouraged to investigate the possibility of applying the
most recent editions of the standards indicated below. Members of IEC and ISO maintain registers of currently val
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.