prEN 15685

Building Hardware - Locks and latches - Multipoint locks and their locking plates - Requirements and test methods

This European Standard specifies requirements and test methods for durability, strength, security and function of mechanically operated multipoint locks and their locking plates for use in doors, window doors and entrance doors in buildings.This standard covers systems comprising more than one locking point or anti-separation point or clenching point between door leaf and frame, interlinked and centrally controlled and /or operated.  Multipoint locks and their locking plates used in fire resistant and/or smoke control door assemblies require additional attributes to comply with the Essential Requirement "Safety in case of fire" either independently, or as a part of a complete assembly. Additional requirements for multipoint locks and their locking plates used on fire resistant and/or smoke control door assemblies are specified in annex A.This standard specifies only the dimensions and properties required for security and for the assessment of smoke door suitability.This standard does not specify any particular design or installation.The suitability of an electrically operated multipoint lock is determined by additional performance tests specified in WI 33062This European standard does not specify single point locks or their locking plates which are specified by EN 12209.This European standard is not applicable to cylinders, handles, locks for windows, padlocks, locks for safes, furniture locks or prison locks.This standard specifies Multipoint locks and locking systems intended for use in different environmental and security conditions, thus necessitating different grades.

Schlösser und Baubeschläge - Mehrfachverriegelungs-Schlösser und Schließbleche - Anforderungen und Prüfverfahren

Die vorliegende Europäische Norm legt Anforderungen an und Prüfverfahren für die Dauerfunktions¬tüchtigkeit, Festigkeit, Schutzwirkung und Wirkungsweise von mechanisch betätigten Mehrfachverriegelungen und deren Schließbleche fest, die in Türen, Fenstertüren und Eingangstüren von Gebäuden zum Einsatz kommen.
Die vorliegende Norm deckt Systeme ab, die zwischen Türflügel und Zarge mehr als einen Verriegelungs¬punkt oder Aushebelschutzpunkt oder Türanzugspunkt aufweisen, die miteinander verbunden sind und zentral gesteuert und/oder betätigt werden.
Werden Mehrfachverriegelungen und deren Schließbleche an Feuerschutz  und/oder Rauchschutz¬türen eingesetzt, müssen sie zusätzliche Eigenschaften aufweisen, um die grundlegende Anforderung Sicherheit im Brandfall entweder eigenständig oder als Teil einer vollständigen Anlage zu erfüllen. In Anhang A sind zusätzliche Anforderungen an Mehrfachverriegelungen und deren Schließbleche für Feuerschutz  und/oder Rauchschutztüren festgelegt.
Die vorliegende Europäische Norm deckt Mehrfachverriegelungen ab, die entweder in ihrer Gesamtheit durch einen Hersteller gefertigt und in den Handel gebracht werden oder durch mehr als einen Hersteller aus Baugruppen montiert und anschließend in einem Geschäftsabschluss als Bausatz in den Handel gelangen.
Die vorliegende Norm legt lediglich die für die Schutzwirkung und Beurteilung der Eignung als Rauchschutztür erforderlichen Maße und Eigenschaften fest.
Die vorliegende Norm legt keine besondere Konstruktions- oder Installationsweise fest.
Die Eignung einer elektrisch betätigten Mehrfachverriegelung wird durch zusätzliche Leistungs¬prüfungen bestimmt, die in prEN 14846 festgelegt sind.
Die vorliegende Europäische Norm trifft keine Festlegungen für Schlösser und deren Schließbleche mit Einfachverriegelung, die durch EN 12209 behandelt werden.

Quincaillerie pour le bâtiment - Serrures et gâches - Serrures multipoints et leurs gâches - Exigences et méthodes d'essai

La présente Norme européenne spécifie les exigences et les méthodes d’essai relatives à l’endurance, la résistance, la sécurité et le fonctionnement des serrures mécaniques multipoints et de leurs gâches destinées à être utilisées sur des portes, des portes-fenêtres et des portes d’entrée de bâtiments.
La présente norme couvre les systèmes comprenant, entre le vantail et l’huisserie, plusieurs points de verrouillage ou points anti-séparation ou points de serrage, interconnectés et à commande centrale.  
Les serrures multipoints et leurs gâches utilisées sur des blocs-portes coupe-feu et/ou pare-fumée nécessitent des qualités supplémentaires afin de satisfaire à l’exigence essentielle de sécurité en cas d’incendie soit comme élément indépendant, soit en tant que partie d’un ensemble complet. Les exigences supplémentaires pour les serrures multipoints et leurs gâches utilisées sur des blocs-portes coupe-feu et/ou pare-fumée sont spécifiées à l’Annexe A.
La présente Norme européenne couvre les serrures multipoints fabriquées et mises sur le marché dans leur intégralité par un seul fabricant, ou assemblées à partir de sous-ensembles produits par plusieurs fabricants et mises ultérieurement sur le marché sous forme d’un kit faisant l’objet d’une seule transaction.
La présente norme spécifie uniquement les dimensions et propriétés requises pour la sécurité et pour l’évaluation de l’aptitude à l’utilisation sur des portes pare-fumée.
La présente norme ne spécifie pas de conception ou installation particulière.
L’aptitude à l’utilisation d’une serrure électrique multipoints est déterminée par des essais de performance supplémentaires spécifiés dans le WI 33062.
La présente Norme européenne ne spécifie pas de serrures monopoints ou leurs gâches objets de l’EN 12209.
La présente Norme européenne ne s’applique pas aux cylindres, béquilles, serrures pour fenêtres, cadenas, serrures assurant la sécurité des personnes, serrures de meubles ou serrures de prison.

Stavbno okovje - Ključavnice in zapahi - Večtočkovne ključavnice in njihovi prijemniki - Zahteve in preskusne metode

General Information

• Status: Not Published
• ICS: 91.190 - Building accessories
• Technical Committee: CEN/TC 33 - Doors, windows, shutters and building hardware
• Drafting Committee: CEN/TC 33/WG 4 - Building hardware
• Current Stage: 4098 - Decision to abandon - Enquiry
• Start Date: 09-Jan-2009
• Completion Date: 09-Jan-2009
• Directive: 305/2011 - Regulation (eu) No 305/2011 of the European Parliament and of the Council of 9 march 2011 laying down harmonised conditions for the marketing of construction products and repealing council directive 89/106/eec
• Directive: 89/106/EEC - Construction products
• Mandate: M/101 - Mandate to CEN/CENELEC concerning the execution of standardization work for harmonized standards on doors, windows and related products
• Ref Project: oSIST prEN 15685:2007 - Building Hardware - Locks and latches - Multipoint locks and their locking plates - Requirements and test methods

Standards Content (Sample)

SLOVENSKI STANDARD
oSIST prEN 15685:2007
01-julij-2007
6WDYEQRRNRYMH.OMXþDYQLFHLQ]DSDKL9HþWRþNRYQHNOMXþDYQLFHLQQMLKRYL
SULMHPQLNL=DKWHYHLQSUHVNXVQHPHWRGH
Building Hardware - Locks and latches - Multipoint locks and their locking plates -
Requirements and test methods
Ta slovenski standard je istoveten z: prEN 15685
ICS:
91.190 Stavbna oprema Building accessories
oSIST prEN 15685:2007 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
EUROPEAN STANDARD
DRAFT
prEN 15685
NORME EUROPÉENNE
EUROPÄISCHE NORM
May 2007
ICS

English Version
Building Hardware - Locks and latches - Multipoint locks and
their locking plates - Requirements and test methods
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee CEN/TC 33.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which
stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other language
made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the
same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2007 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 15685:2007: E
worldwide for CEN national Members.

---------------------- Page: 2 ----------------------
prEN 15685:2007 (E)
Contents Page
Foreword.5
Introduction.6
1 Scope.7
2 Normative references.7
3 Terms, definitions, symbols and abbreviations .8
3.1 Terms and definitions .8
3.2 Symbols, units and abbreviations .9
4 Classification.12
4.1 General.12
4.2 Classification for mechanically operated multipoint locks and locking plates .12
4.2.1 Category of use (first digit).12
4.2.2 Durability (second digit).12
4.2.3 Door mass and closing force (third digit) .13
4.2.4 Suitability for use on fire/smoke doors (fourth digit).13
4.2.5 Safety (fifth digit) .14
4.2.6 Corrosion resistance and temperature (sixth digit).14
4.2.7 Security (seventh digit).14
4.2.8 Field of door application (eighth digit) .14
4.2.9 Type of key operation and locking (ninth digit).15
4.2.10 Type of spindle operation (tenth digit) .16
4.2.11 Key identification of lever locks (eleventh digit).16
4.2.12 Anti-separation (twelfth digit).17
4.2.13 Clenching (thirteenth digit).17
4.2.14 Example of classification for multipoint locks and their locking plates.17
5 Requirements.18
5.1 General.18
5.1.1 Dangerous substances.18
5.1.2 Return force of latch bolts.18
5.2 Category of use.18
5.2.1 Resistance to side load on latch bolt .18
5.2.2 Torque to operate the lock.18
5.2.3 Strength of follower stops .19
5.2.4 Torque resistance of lockable follower. .19
5.3 Durability requirements.19
5.3.1 Durability of latch action.19
5.3.2 Durability of locking action.19
5.3.3 Durability of locking snib mechanism.20
5.3.4 Durability of clenching .20
5.4 Door mass and closing force .20
5.4.1 Door mass.20
5.5 Suitability for use on fire/smoke doors .20
5.6 Safety.20
5.7 Corrosion resistance and temperature .20
5.7.1 Corrosion resistance.20
5.7.2 Operation at extremes of temperature .21
5.8 Security.21
5.8.1 Torque resistance of lockable follower .21
5.8.2 Requirements for side load .21
5.8.3 Locking point bolt projection .21
2

---------------------- Page: 3 ----------------------
prEN 15685:2007 (E)
5.8.4 Requirements for end load on locking point.21
5.8.5 Security requirements of the locking plate.22
5.9 Field of door application.23
5.9.1 General.23
5.9.2 Protection against removal from door .24
5.10 Type of key operation and locking .24
5.10.1 Strength of key .24
5.10.2 Deadlocking.24
5.11 Type of spindle operations.25
5.11.1 Strength of bolt action. .25
5.11.2 Minimum restoring torque.25
5.12 Key Identification requirements of lever locks.26
5.12.1 Detaining elements.26
5.12.2 Effective differs.26
5.12.3 Differing step heights on key .26
5.12.4 Non-interpassing of keys with just one interval differ .26
5.12.5 Coding protection.26
5.13 Anti-separation requirements.26
5.13.1 Resistance to pulling of anti-separation device.26
5.13.2 Resistance to drilling and pulling of anti-separation device .27
5.13.3 Resistance to disengaging of anti-separation device .27
5.13.4 Resistance to drilling and disengaging of anti-separation device.27
5.13.5 Resistance to pulling on locking plate for the anti-separation device .27
5.14 Clenching.28
6 Test methods.28
6.1.1 Dangerous substances.29
6.1.2 Return force of latch bolt.29
6.2 Category of use .30
6.2.1 Resistance to side load on latch bolt(s).30
6.2.2 Torque to operate lock.30
6.2.3 Strength of follower stops.30
6.2.4 Torque resistance of lockable follower.30
6.3 Durability tests.30
6.3.1 Durability tests of latch action .30
6.3.2 Durability of locking action .31
6.3.3 Durability of locking snib mechanism.32
6.3.4 Durability of clenching action .32
6.4 Door mass and closing force .33
6.4.1 Door mass.33
6.4.2 Door closing force.33
6.5 Suitability for use on fire/smoke doors.33
6.6 Safety tests.33
6.7 Corrosion resistance and temperature .33
6.7.1 Corrosion resistance.33
6.7.2 Operation at extremes of temperature .34
6.8 Security tests.34
6.8.1 Torque resistance of lockable follower.34
6.8.2 Requirements for side load .34
6.8.3 Locking point bolt projection.35
6.8.4 Requirements for end load on locking point.35
6.8.5 Test for security requirements for the locking plate .35
6.9 Field of door application.36
6.9.1 General.36
6.9.2 Protection against removal from door .36
6.10 Type of key operation and locking .36
6.10.1 Strength of key .36
6.10.2 Deadlocking.36
6.11 Type of spindle operation.37
6.11.1 Strength of bolt action. .37
3

---------------------- Page: 4 ----------------------
prEN 15685:2007 (E)
6.11.2 Minimum restoring torque .37
6.12 Key Identification requirements of lever locks.37
6.12.1 Detaining elements.37
6.12.2 Effective differs.37
6.12.3 Differing step heights on key .37
6.12.4 Non-interpassing of keys with just one interval differ.38
6.12.5 Coding protection.38
6.13 Test of Anti-separation prevision requirements.38
6.13.1 Resistance to pulling of anti-separation device.38
6.13.2 Resistance to drilling and pulling of anti-separation device .38
6.13.3 Resistance to disengaging anti-separation device.38
6.13.4 Resistance to drilling and disengaging of anti-separation device.38
6.13.5 Resistance to pulling on locking plate for the anti-separation device .39
7 Marking.39
8 Evaluation of conformity.40
8.1 Initial type test.40
8.2 Factory production control.41
8.2.1 Documentation.41
8.2.2 Unit checks during manufacture.41
8.2.3 Treatment of non-conforming parts .41
8.2.4 Further testing of samples.41
Annex A (normative) Locks for use on fire / smoke doors.42
A.1 Grade A:.42
A.2 Grade B to F: .42
Annex B (normative) Test apparatus - Illustrations.43
Annex C (normative) Test sampling and sequencing .47
Annex ZA (normative) Clauses of this European Standard addressing the provisions of the EU
Construction Products Directive (89/106/EEC).49
Bibliography.55

4

---------------------- Page: 5 ----------------------
prEN 15685:2007 (E)
Foreword
This document (prEN 15685:2007) has been prepared by Technical Committee CEN/TC 33 “Doors, windows,
shutters, building hardware and curtain walling”, the secretariat of which is held by AFNOR.
This document is currently submitted to the CEN Enquiry.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive(s).
For relationship with EU Directive(s), see informative Annex ZA, B, C or D, which is an integral part of this
document.
No existing European Standard is superseded.
This European standard is one of a series of European standards dedicated to building hardware products.
Complementing this standard is a standard for mechanically operated locks and latches (EN 12209), and a
draft for electromechanically operated locks and locking plates (prEN 14846)
Normative and informative annexes to this standard are indicated in the contents list.
The performance tests incorporated in this standard are considered to be reproducible and as such will
provide a consistent and objective assessment of the performance of these products throughout CEN Member
States.
5

---------------------- Page: 6 ----------------------
prEN 15685:2007 (E)
Introduction
Experiences relating to security and environmental conditions encountered in residential, commercial and
public buildings have indicated a need to provide, in some applications, additional locking points to locks
installed on doors, window doors and entrance doors.
These additional locking points are designed to ensure sufficient performance, weather tightness and/or attack
resistance of doors.
6

---------------------- Page: 7 ----------------------
prEN 15685:2007 (E)
1 Scope
This European Standard specifies requirements and test methods for durability, strength, security and function
of mechanically operated multipoint locks and their locking plates for use in doors, window doors and entrance
doors in buildings.
This standard covers systems comprising more than one locking point or anti-separation point or clenching
point between door leaf and frame, interlinked and centrally controlled and /or operated.
Multipoint locks and their locking plates used in fire resistant and/or smoke control door assemblies require
additional attributes to comply with the Essential Requirement "Safety in case of fire" either independently, or
as a part of a complete assembly. Additional requirements for multipoint locks and their locking plates used on
fire resistant and/or smoke control door assemblies are specified in annex A.
This European Standard covers multipoint locks which are either manufactured and placed on the market in
their entirety by one producer or assembled from sub-assemblies produced by more than one producer and
subsequently placed on the market as a kit in a single transaction.
This standard specifies only the dimensions and properties required for security and for the assessment of
smoke door suitability.
This standard does not specify any particular design or installation.
The suitability of an electrically operated multipoint lock is determined by additional performance tests
specified in WI 33062
This European standard does not specify single point locks or their locking plates which are specified by EN
12209.
This European standard is not applicable to cylinders, handles, locks for windows, padlocks, locks for safes,
furniture locks or prison locks.
This standard specifies Multipoint locks and locking systems intended for use in different environmental and
security conditions, thus necessitating different grades.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.


EN 1634-1, Fire testing of door and shutter assemblies — Part 1: Method of test for fire resistance of fire
doors and shutters
EN 1670: 1998, Building hardware — Corrosion resistance — Requirements and test methods
ISO 10899: 1996, High-speed steel two-flute drills — Technical specifications
7

---------------------- Page: 8 ----------------------
prEN 15685:2007 (E)
3 Terms, definitions, symbols and abbreviations
3.1 Terms and definitions
For the purposes of this European Standard the following terms and definitions apply:
3.1.1
anti-separation point
an arrangement of components to prevent the separation of a door leaf from its frame or adjacent door leaf in
the plane of the door
3.1.2
bolt
movable part of a lock that usually engages a component fixed to a frame, and withdraws into a lockcase
3.1.3
centrally controlled
having operation of all of its locking and/or clenching and/or anti-separation points, affected, enabled or
prevented from a single lockcase
3.1.4
clenching point
an arrangement of components to draw together a door and its frame in the door closing direction to reduce
distortion of the door and/or compress seal.(not necessarily a locking point)
3.1.5
cylinder
device, usually separate from, but engaging with, its associated lock, operated by a key
3.1.6
cylinder lock
lock in which the lock mechanism is operated by one or more cylinders
3.1.7
deadbolt
bolt that is operated at least in one direction by a key, handle and/or thumb turn
3.1.8
follower
part of a lock that operates the bolts and/or clenching and/or anti-separation points when turned by a spindle
3.1.9
forend
part of a mortise lockcase by which the lock is fixed to the door
3.1.10
interlinked
connected for the purpose of operation
3.1.11
key
device that is removable and portable and used to operate the lock
3.1.12
latch action
arrangement and performance of the constituent parts that operate a latch bolt
8

---------------------- Page: 9 ----------------------
prEN 15685:2007 (E)
3.1.13
latch bolt
spring-loaded bolt that automatically engages a locking plate to keep the door in its closed position
3.1.14
lock
fastener which secures a door leaf in its closed position and which is operated by a key or other device
3.1.15
lockcase
part of a lock in which the lock mechanism is housed
3.1.16
locking plate
a component, which is normally fixed to a door frame to engage at least a bolt or an anti-separation point or a
clenching point
3.1.17
locking point
an arrangement of components interacting between a bolt and locking plate for security purpose
NOTE Bolts separated by less than 150 mm in the same plane, between the closest points on their adjacent surfaces
in the plane of the forend in locked position, constitute one locking point only.
Bolts operating in different planes are separate locking points
3.1.18
lock mechanism
constituent parts of a lock that operate at least a bolt or an anti-separation point or a clenching point and,
where required, provide the differs
3.1.19
mortice loc
...