EN 4015:2004

Aerospace series - Inserts, thickwall, self-locking - Installation and removal procedure

This standard specifies the conditions of installation and removal procedure (hole serration profile, tools, swaging) of self-locking thickwall inserts defined by EN standards, for aerospace applications.

Luft- und Raumfahrt - Gewindeeinsätze, dickwandig, selbstsichernd - Ein- und Ausbauverfahren

Diese Norm legt die Bedingungen für das Ein  und Ausbauverfahren (Lochverzahnungsprofil, Werkzeuge, Aufweiten) für selbstsichernde, dickwandige Gewindeeinsätze nach EN-Normen für Anwendungen in der Luft  und Raumfahrt fest.

Série aérospatiale - Douilles filetées, à paroi renforcée, à freinage interne - Procédure d'installation et d'extraction

Aerospace series - Inserts, thickwall, self-locking - Installation and removal procedure

General Information

• Status: Published
• Publication Date: 09-Nov-2004
• Withdrawal Date: 30-May-2005
• ICS: 49.030.30 - Nuts
• Technical Committee: ASD-STAN - Aerospace
• Drafting Committee: ASD-STAN/D 3 - Mechanical
• Current Stage: 9093 - Decision to confirm - Review Enquiry
• Completion Date: 30-Jun-2017
• Ref Project: SIST EN 4015:2005 - Aerospace series - Inserts, thickwall, self-locking - Installation and removal procedure

Relations

• Replaces: EN 4015:2003 - Aerospace series - Inserts, thickwall, self-locking - Installation and removal procedure
• Effective Date: 22-Dec-2008

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 4015:2005
01-junij-2005
1DGRPHãþD
SIST EN 4015:2004
Aerospace series - Inserts, thickwall, self-locking - Installation and removal
procedure
Aerospace series - Inserts, thickwall, self-locking - Installation and removal procedure
Luft- und Raumfahrt - Gewindeeinsätze, dickwandig, selbstsichernd - Ein- und
Ausbauverfahren
Série aérospatiale - Douilles filetées, a paroi renforcée, a freinage interne - Procédure
d'installation et d'extraction
Ta slovenski standard je istoveten z: EN 4015:2004
ICS:
49.030.30 Matice Nuts
SIST EN 4015:2005 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 4015:2005

---------------------- Page: 2 ----------------------

SIST EN 4015:2005



EUROPEAN STANDARD
EN 4015

NORME EUROPÉENNE

EUROPÄISCHE NORM
November 2004
ICS 49.030.30 Supersedes EN 4015:2003
English version
Aerospace series - Inserts, thickwall, self-locking - Installation
and removal procedure
Série aérospatiale - Douilles filetées, à paroi renforcée, à Luft- und Raumfahrt - Gewindeeinsätze, dickwandig,
freinage interne - Procédure d'installation et d'extraction Selbstsichernd - Ein- und Ausbauverfahren
This European Standard was approved by CEN on 11 September 2003.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Central Secretariat or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official
versions.

CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.




EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2004 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 4015:2004: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN 4015:2005

EN 4015:2004 (E)
Contents Page
Foreword.3
1 Scope .4
2 Normative references .4
3 Insert information .4
4 Broaching .5
5 Hole serration profile.7
6 Inspection requirements before installation.8
7 Installation tools .8
8 Checks of insert position and crimping .11
9 Inspection of minimum self-locking torque.12
10 Insert removal .13
11 Repair.14

2

---------------------- Page: 4 ----------------------

SIST EN 4015:2005
EN 4015:2004 (E)
Foreword
This document (EN 4015:2004) has been prepared by the European Association of Aerospace
Manufacturers - Standardization (AECMA-STAN).
After enquiries and votes carried out in accordance with the rules of this Association, this Standard has
received the approval of the National Associ
...