prEN ISO 3325
(Main)Sintered metal materials, excluding hardmetals - Determination of transverse rupture strength (ISO/DIS 3325:2024)
Sintered metal materials, excluding hardmetals - Determination of transverse rupture strength (ISO/DIS 3325:2024)
Gives a method for the determination of the transverse rupture strength of sintered metals, excluding hardmetals. Particularly suitable for comparing the sintered strength of a batch of metal powder with that of a reference powder or with a reference strength.
Sintermetalle, ausgenommen Hartmetalle - Ermittlung der Biegebruchfestigkeit (ISO/DIS 3325:2024)
Matériaux métalliques frittés à l'exclusion des métaux-durs - Détermination de la résistance à la rupture transversale (ISO/DIS 3325:2024)
La présente Norme internationale prescrit une méthode pour la détermination de la résistance à la rupture transversale des matériaux métalliques frittés, à l'exclusion des métaux-durs. Cette méthode est particulièrement adaptée à la comparaison de la résistance à l'état fritté d'un lot de poudre métallique à celle d'une poudre ou à une valeur de résistance de référence. La présente méthode est applicable aux matériaux métalliques frittés, à l'exclusion des métaux-durs, qu'ils aient ou non été soumis à un traitement thermique après frittage, ainsi qu'aux matériaux calibrés ou matricés après frittage. Elle est avant tout applicable aux matériaux de dureté uniforme dans la totalité de leur section et de ductilité négligeable, c'est-à-dire de ductilité correspondant à une déformation rémanente, résultant de l'essai et mesurée entre les deux supports, inférieure à 0,5 mm environ (voir note 1). Si l'essai est effectué sur des matériaux se trouvant dans des conditions autres que celles prescrites ci-dessus, les nouvelles conditions doivent être indiquées. NOTE 1 La déformation rémanente peut être mesurée avec une précision suffisante sur les deux fragments d'un barreau cassé ou d'un barreau fissuré par repérage de la surface inférieure. Il est également possible de mesurer, à l'aide d'un dispositif optique (microscope de mesure, comparateur optique, etc.) la courbure d'une droite tracée horizontalement sur le côté du barreau.
Sintrani kovinski materiali, razen trdin - Določanje prečne lomne trdnost (ISO/DIS 3325:2024)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-september-2024
Sintrani kovinski materiali, razen trdin - Določanje prečne lomne trdnost (ISO/DIS
3325:2024)
Sintered metal materials, excluding hardmetals - Determination of transverse rupture
strength (ISO/DIS 3325:2024)
Sintermetalle, ausgenommen Hartmetalle - Ermittlung der Biegebruchfestigkeit (ISO/DIS
3325:2024)
Matériaux métalliques frittés à l'exclusion des métaux-durs - Détermination de la
résistance à la rupture transversale (ISO/DIS 3325:2024)
Ta slovenski standard je istoveten z: prEN ISO 3325
ICS:
77.040.10 Mehansko preskušanje kovin Mechanical testing of metals
77.160 Metalurgija prahov Powder metallurgy
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
DRAFT
International
Standard
ISO/DIS 3325
ISO/TC 119/SC 3
Sintered metal materials, excluding
Secretariat: DIN
hardmetals — Determination of
Voting begins on:
transverse rupture strength
2024-07-08
Matériaux métalliques frittés à l'exclusion des métaux-durs —
Voting terminates on:
Détermination de la résistance à la rupture transversale
2024-09-30
ICS: 77.160; 77.040.10
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENTS AND APPROVAL. IT
IS THEREFORE SUBJECT TO CHANGE
AND MAY NOT BE REFERRED TO AS AN
INTERNATIONAL STANDARD UNTIL
PUBLISHED AS SUCH.
This document is circulated as received from the committee secretariat.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
ISO/CEN PARALLEL PROCESSING
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
NATIONAL REGULATIONS.
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION.
Reference number
ISO/DIS 3325:2024(en)
DRAFT
ISO/DIS 3325:2024(en)
International
Standard
ISO/DIS 3325
ISO/TC 119/SC 3
Sintered metal materials, excluding
Secretariat: DIN
hardmetals — Determination of
Voting begins on:
transverse rupture strength
Matériaux métalliques frittés à l'exclusion des métaux-durs —
Voting terminates on:
Détermination de la résistance à la rupture transversale
ICS: 77.160; 77.040.10
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENTS AND APPROVAL. IT
IS THEREFORE SUBJECT TO CHANGE
AND MAY NOT BE REFERRED TO AS AN
INTERNATIONAL STANDARD UNTIL
PUBLISHED AS SUCH.
This document is circulated as received from the committee secretariat.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
© ISO 2024
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
STANDARDS MAY ON OCCASION HAVE TO
ISO/CEN PARALLEL PROCESSING
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
BE CONSIDERED IN THE LIGHT OF THEIR
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
or ISO’s member body in the country of the requester.
NATIONAL REGULATIONS.
ISO copyright office
RECIPIENTS OF THIS DRAFT ARE INVITED
CP 401 • Ch. de Blandonnet 8
TO SUBMIT, WITH THEIR COMMENTS,
CH-1214 Vernier, Geneva
NOTIFICATION OF ANY RELEVANT PATENT
Phone: +41 22 749 01 11
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION.
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland Reference number
ISO/DIS 3325:2024(en)
ii
ISO/DIS 3325:2024(en)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principle . 1
5 Apparatus . 1
6 Test piece . 2
7 Procedure . 3
8 Expression of results . 3
9 Precision . 3
10 Test report . 4
iii
ISO/DIS 3325:2024(en)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out through
ISO technical committees. Each member body interested in a subject for which a technical committee
has been established has the right to be represented on that committee. International organizations,
governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely
with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described
in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types
of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the
ISO/IEC Directives, Part 2 (see www.iso.org/directives).
ISO draws attention to the possibility that the implementation of this document may involve the use of (a)
patent(s). ISO takes no position concerning the evidence, validity or applicability of any claimed patent
rights in respect thereof. As of the date of publication of this document, ISO had not received notice of (a)
patent(s) which may be required to implement this document. However, implementers are cautioned that
this may not represent the latest information, which may be obtained from the patent database available at
www.iso.org/patents. ISO shall not be held responsible for identifying any or all such patent rights.
Any t
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.