iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

prEN 1680

(Main)

Plastics piping systems - Valves for polyethylene (PE) piping systems - Test method for leaktightness under and after bending applied to the operating mechanisms

Plastics piping systems - Valves for polyethylene (PE) piping systems - Test method for leaktightness under and after bending applied to the operating mechanisms

This document specifies a test method for PE valves to maintain tightness during and after being subjected to a force, applied as a bending moment to the operating mechanism.
Valves according to these standards are intended for use in polyethylene (PE) piping systems for the transport of fluids.
When specified in the product document, this document can be applied to valves and plastics pipes of material different than PE.

Kunststoff-Rohrleitungssysteme - Armaturen für Systeme aus Polyethylen (PE) - Prüfverfahren für die Dichtheit während und nach der Aufbringung eines Biegemoments auf den Betätigungsmechanismus

Dieses Dokument legt ein Prüfverfahren für Armaturen aus PE zur Aufrechterhaltung der Dichtheit während und nach Einwirkung einer Kraft fest, die als Biegemoment auf den Betätigungsmechanismus aufgebracht wird.
Armaturen nach diesen Normen sind für den Einsatz in Rohrleitungssystemen aus Polyethylen (PE) für den Transport von Flüssigkeiten vorgesehen.
Wenn im Produktdokument festgelegt, kann dieses Dokument auf Armaturen und Kunststoffrohre aus einem anderen Werkstoff als PE angewendet werden.

Systèmes de canalisations en plastique - Robinets pour les systèmes de canalisations en polyéthylène (PE) - Méthode d'essai d'étanchéité sous et après une flexion appliquée au mécanisme d'entraînement

Le présent document spécifie une méthode d’essai pour les robinets en PE devant maintenir l’étanchéité pendant et après avoir été soumis à une force, appliquée comme un moment de flexion au mécanisme d’entrainement.
Les robinets conformes à ces normes sont destinés à être utilisés dans des systèmes de canalisations en polyéthylène (PE) pour le transport de fluide.
Lorsque cela est spécifié dans le document du produit, le présent document peut être appliqué aux robinets et tubes en plastique d’un matériau autre que le PE.

Cevni sistemi iz polimernih materialov - Ventili za cevne sisteme iz polietilena (PE) - Metoda za preskus neprepustnosti med upogibanjem zaradi uporabe zapiralnih mehanizmov in po njem

General Information

Status
Not Published
Publication Date
26-Feb-2025
ICS
23.060.01 - Valves in general
Technical Committee
CEN/TC 155 - Plastics piping systems and ducting systems
Drafting Committee
CEN/TC 155/WG 32 - Valves
Current Stage
4060 - Closure of enquiry - Enquiry
Start Date
25-Jan-2024
Due Date
04-Jan-2024
Completion Date
25-Jan-2024
Directive
305/2011 - Regulation (eu) No 305/2011 of the European Parliament and of the Council of 9 march 2011 laying down harmonised conditions for the marketing of construction products and repealing council directive 89/106/eec
Ref Project
oSIST prEN 1680:2024 - Plastics piping systems - Valves for polyethylene (PE) piping systems - Test method for leaktightness under and after bending applied to the operating mechanisms

Relations

Revises
EN 1680:1997 - Plastics piping systems - Valves for polyethylene (PE) piping systems - Test method for leaktightness under and after bending applied to the operating mechanisms
Effective Date
22-Jan-2023

Buy Standard

prEN 1680:2024prEN 1680:2024
PreviousNext
Draft
prEN 1680:2024
English language
10 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
oSIST prEN 1680:2024
01-januar-2024
Cevni sistemi iz polimernih materialov - Ventili za cevne sisteme iz polietilena (PE)
- Metoda za preskus neprepustnosti med upogibanjem zaradi uporabe zapiralnih
mehanizmov in po njem
Plastics piping systems - Valves for polyethylene (PE) piping systems - Test method for
leaktightness under and after bending applied to the operating mechanisms
Kunststoff-Rohrleitungssysteme - Armaturen für Systeme aus Polyethylen (PE) -
Prüfverfahren für die Dichtheit während und nach der Aufbringung eines Biegemoments
auf den Betätigungsmechanismus
Systèmes de canalisations en plastique - Robinets pour les systèmes de canalisations
en polyéthylène (PE) - Méthode d'essai d'étanchéité sous et après une flexion appliquée
au mécanisme d'entraînement
Ta slovenski standard je istoveten z: prEN 1680
ICS:
23.060.01 Ventili na splošno Valves in general
83.140.30 Polimerne cevi in fitingi za Plastics pipes and fittings for
snovi, ki niso tekočine non fluid use
oSIST prEN 1680:2024 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN 1680:2024

---------------------- Page: 2 ----------------------
oSIST prEN 1680:2024


DRAFT
EUROPEAN STANDARD
prEN 1680
NORME EUROPÉENNE

EUROPÄISCHE NORM

November 2023
ICS 23.060.01 Will supersede EN 1680:1997
English Version

Plastics piping systems - Valves for polyethylene (PE)
piping systems - Test method for leaktightness under and
after bending applied to the operating mechanisms
Systèmes de canalisations en plastique - Robinets pour Kunststoff-Rohrleitungssysteme - Armaturen für
les systèmes de canalisations en polyéthylène (PE) - Systeme aus Polyethylen (PE) - Prüfverfahren für die
Méthode d'essai d'étanchéité sous et après une flexion Dichtheit während und nach der Aufbringung eines
appliquée au mécanisme d'entraînement Biegemomentes auf den Betätigungsmechanismus
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 155.

If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.

Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.


EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2023 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 1680:2023 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
oSIST prEN 1680:2024
prEN 1680:2023 (E)
Contents Page
EUROPEAN FOREWORD . 3
1 SCOPE . 4
2 NORMATIVE REFERENCES . 4
3 TERMS AND DEFINITIONS . 4
4 PRINCIPLE . 5
5 APPARATUS . 5
5.1 TEMPERATURE-CONTROLLED TANK .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN 12201-4:2024(Main)
Plastics piping systems for water supply, and for drains and sewers under pressure - Polyethylene (PE) - Part 4: Valves for water supply systems
SIST EN 12201-4:2024

This document specifies the characteristics of valves or valve bodies made from polyethylene (PE) for buried and above ground applications, intended for the conveyance of water for human consumption, raw water prior to treatment, drains and sewers under pressure, vacuum sewer systems, and water for other purposes, with the exception of industrial applications.
NOTE 1   For PE components intended for the conveyance of water for human consumption and raw water prior to treatment, attention is drawn to 6.4. Components manufactured for water for other purposes, drains and sewers, and vacuum systems are possibly not suitable for water supply for human consumption.
NOTE 2   Industrial application is covered by EN ISO 15494 [2].
The intended use includes sea outfalls, laid in water and pipes suspended below bridges.
It is applicable to isolating unidirectional and bi-directional valves with spigot ends or electrofusion sockets intended to be fused with PE pipes or fittings conforming to EN 12201-2 and EN 12201-3 respectively.
Valves made from materials other than PE, conforming to the relevant standards can be used in PE piping systems according to EN 12201, provided that they have PE connections for butt fusion or electrofusion ends, conforming to EN 12201-3, or material transition joints (e.g. flanged joints).
NOTE 3   For valves or valve bodies intended for drains and sewers, additional information is given in Clause 9.
It also specifies the test parameters for the test methods referred to in this document.
In conjunction with EN 12201-1, EN 12201 2, EN 12201 3 and EN 12201 5, this document is applicable to PE pipes, fittings and valves, their joints and joints with components of PE and other materials intended to be used under the following conditions:
a)   allowable operating pressure, PFA, up to 25 bar ;
b)   an operating temperature of 20 °C as a reference temperature.
NOTE 4   For applications operating at constant temperature greater than 20 °C and up to 50 °C, see EN 12201-1:2024, Annex A.
The EN 12201 series covers a range of allowable operating pressures and gives requirements concerning colours and additives.
NOTE 5   It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national guidance or regulations and installation practices or codes.
This document covers valves for pipes with a nominal outside diameter dn ≤ 400 mm.

  • Standard
    27 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 17778:2015(Main)
Plastics piping systems - Fittings, valves and ancillaries - Determination of gaseous flow rate/pressure drop relationships (ISO 17778:2015)
SIST EN ISO 17778:2015

ISO 17778:2015 specifies a method for determining the flow rate/pressure drop relationship of components for plastics piping systems when tested using air at 25 mbar.

  • Standard
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 1452-4:2009(Main)
Plastics piping systems for water supply and for buried and above-ground drainage and sewerage under pressure - Unplasticized poly(vinyl chloride) (PVC-U) - Part 4: Valves (ISO 1452-4:2009)
SIST EN ISO 1452-4:2010

ISO 1452-4:2009 specifies the characteristics of valves made from unplasticized poly(vinyl chloride) (PVC‑U) for piping systems intended for water supply and for buried and above-ground drainage and sewerage under pressure. It also specifies the test parameters for the test methods referred to.
In conjunction with ISO 1452-1, ISO 1452-2, ISO 1452-3 and ISO 1452-5 it is applicable to PVC‑U valves with components of PVC-U, other plastics and non-plastics materials intended to be used for the following:
- water mains and services buried in ground;
- conveyance of water above ground for both outside and inside buildings;
- buried and above-ground drainage and sewerage under pressure.
It is applicable to valves in piping systems intended for the supply of water under pressure up to and including 25 °C (cold water) intended for human consumption and for general purposes as well as for waste water under pressure. It is also applicable to valves for the conveyance of water and waste water up to and including 45 °C.

  • Standard
    19 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 12119:1997(Main)
Plastics piping systems - Polyethylene (PE) valves - Test method for resistance to thermal cycling
SIST EN 12119:1999

This standard specifies a test method for the resistance of valves to thermal cycling. This standard is applicable to polyethylen (PE) valves and valves with PE spigot-ends having a nominal outside diameter greater than 63 mm and intended for the transport of fluids.

  • Standard
    5 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1680:1997(Main)
Plastics piping systems - Valves for polyethylene (PE) piping systems - Test method for leaktightness under and after bending applied to the operating mechanisms
SIST EN 1680:1999

This draft standard specifies a method for testing the ability of a valve, intended for use in PE piping systems for gas supply, to maintain its pressure retaining capabilities under and after being subject to a bending moment appliedto the operating mechanism (cap).

  • Standard
    7 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1705:1996(Main)
Plastics piping systems - Thermoplastics valves - Test method for the integrity of a valve after an external blow
SIST EN 1705:1997

This standard specifies a method for determining the leaktightness and the ease of operation of a valve following an impact applied to the operating mechanism (cap) or other exposed mechanism.

  • Standard
    6 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
prEN 1705(Main)
Plastics piping systems - Thermoplastics valves - Test method for the integrity of a valve after an external blow
oSIST prEN 1705:2024

This document specifies a test method for determining the leaktightness and the ease of operation of a valve made of thermoplastic material following an impact applied to the operating device.
Additionally, a different procedure of the test on diaphragm valve can be specified by the valve manufacturer.

  • Draft
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 8233:2024(Main)
Thermoplastics valves - Torque - Test method (ISO 8233:2024)
SIST EN ISO 8233:2024

This document specifies a test method for the determination of the opening, closing and running torque of thermoplastics valves.
This document is applicable to all types of manually operable thermoplastics valves, with or without actuator, intended to be used for the transport of fluids.
NOTE 1        Examples of valve types tested with this method are in ISO 4437-4, ISO 16135, ISO 16136, ISO 16138, ISO 16139, ISO 16486-4, ISO 21787, EN 1555-4[13] and EN 12201-4 [14].
This document does not specify the relationship between the torque and its possible increase after prolonged use of the valve under a specific working condition or wear/chemical aggression of the materials.
NOTE 2        Concerning the chemical aggression of the materials, a collection of data is reported in ISO/TR 10358 concerning the endurance test necessary to confirm the ability of hand-operated plastics valves to withstand prolonged use with repeated opening and closing operations. Further information is provided in ISO 8659.

  • Standard
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 12201-4:2024(Main)
Plastics piping systems for water supply, and for drains and sewers under pressure - Polyethylene (PE) - Part 4: Valves for water supply systems
SIST EN 12201-4:2024

This document specifies the characteristics of valves or valve bodies made from polyethylene (PE) for buried and above ground applications, intended for the conveyance of water for human consumption, raw water prior to treatment, drains and sewers under pressure, vacuum sewer systems, and water for other purposes, with the exception of industrial applications.
NOTE 1   For PE components intended for the conveyance of water for human consumption and raw water prior to treatment, attention is drawn to 6.4. Components manufactured for water for other purposes, drains and sewers, and vacuum systems are possibly not suitable for water supply for human consumption.
NOTE 2   Industrial application is covered by EN ISO 15494 [2].
The intended use includes sea outfalls, laid in water and pipes suspended below bridges.
It is applicable to isolating unidirectional and bi-directional valves with spigot ends or electrofusion sockets intended to be fused with PE pipes or fittings conforming to EN 12201-2 and EN 12201-3 respectively.
Valves made from materials other than PE, conforming to the relevant standards can be used in PE piping systems according to EN 12201, provided that they have PE connections for butt fusion or electrofusion ends, conforming to EN 12201-3, or material transition joints (e.g. flanged joints).
NOTE 3   For valves or valve bodies intended for drains and sewers, additional information is given in Clause 9.
It also specifies the test parameters for the test methods referred to in this document.
In conjunction with EN 12201-1, EN 12201 2, EN 12201 3 and EN 12201 5, this document is applicable to PE pipes, fittings and valves, their joints and joints with components of PE and other materials intended to be used under the following conditions:
a)   allowable operating pressure, PFA, up to 25 bar ;
b)   an operating temperature of 20 °C as a reference temperature.
NOTE 4   For applications operating at constant temperature greater than 20 °C and up to 50 °C, see EN 12201-1:2024, Annex A.
The EN 12201 series covers a range of allowable operating pressures and gives requirements concerning colours and additives.
NOTE 5   It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national guidance or regulations and installation practices or codes.
This document covers valves for pipes with a nominal outside diameter dn ≤ 400 mm.

  • Standard
    27 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 19:2023(Main)
Industrial valves - Marking of metallic valves
SIST EN 19:2024

This document specifies the requirements for marking of industrial metallic valves. It defines the method of applying the markings, on the body, on a flange, on an identification plate or any other location.
When specified as a normative reference in a valve product or performance standard, this document is considered in conjunction with the specified requirements of that valve product or performance standard.
The marking requirements for plastic valves are not within the scope of this document.

  • Standard
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day