FprEN 15015
(Main)Plastics piping systems - Hot and cold water piping components - Requirements and test/assessment methods for pipes and fittings
Plastics piping systems - Hot and cold water piping components - Requirements and test/assessment methods for pipes and fittings
This European Standard specifies requirements for plastics pipes and fittings for hot and cold water installations.
It is intended to be used for distribution of hot and cold water and for heating systems inside buildings with the exception of water intended for human consumption.
It gives associated test/assessment methods.This standard does not cover adhesives joint sealings and gasket
NOTE 1 For this standard the term fitting includes the term joint as meant by mandate M 131.
NOTE 2 Products complying with this document may be used for the transport of water intended for human consumption if they comply with the relevant national, regional or local regulatory provisions applicable in place of use. Compliance of a product with this document does not confer a presumption of fitness of the product for the transport of water intended for human consumption within the meaning of the Directive 89/106/EEC.
Kunststoff-Rohrleitungssysteme - Bauteile für den Einsatz in Rohrleitungen für Warm- und Kaltwasser - Anforderungen und Prüf /Bewertungsverfahren für Rohre und Formstücke
Diese Europäische Norm legt Anforderungen an Rohre und Formstücke aus Kunststoff für die Warm- und Kaltwasserinstallation fest.
Sie ist anzuwenden für die Verteilung von Warm- und Kaltwasser sowie für Heizungsanlagen innerhalb von Gebäuden mit Ausnahme von Wasser für den menschlichen Gebrauch.
Sie enthält die erforderlichen Prüf-/Bewertungsverfahren. Diese Norm gilt nicht für Klebstoffe und Dichtungen.
ANMERKUNG 1 Für die Anwendung dieser Norm beinhaltet der Begriff „Formstück“ den Begriff „Verbindung“ im Sinne von Mandat M/131.
ANMERKUNG 2 Produkte dürfen bei Übereinstimmung mit diesem Dokument für den Transport von Wasser für den mensch¬lichen Gebrauch verwendet werden, sofern sie die entsprechenden am Einsatzort geltenden nationalen, regio¬nalen oder örtlichen gesetzlichen Bestimmungen oder Empfehlungen erfüllen. Die Übereinstimmung eines Produktes mit diesem Dokument stellt keine Annahme der Gebrauchstauglichkeit des Produktes für den Transport von Wasser für den menschlichen Gebrauch im Sinne der Richtlinie 89/106/EWG dar.
Systèmes de canalisations en plastique - Composants de canalisations pour eau chaude et froide non destinée à la consommation humaine - Exigences et méthodes d'essais/d'évaluation pour tubes et raccords
La présente Norme européenne spécifie les exigences relatives aux tubes et raccords en plastique destinés aux installations d’eau chaude et froide.
Elle est destinée à être utilisée pour la distribution d’eau chaude et froide et pour les systèmes de chauffage à l’intérieur des bâtiments, à l’exception de l’eau destinée à la consommation humaine.
Elle donne des méthodes d’essai/d’évaluation associée. La présente norme ne couvre pas les adhésifs, les garnitures de joints et les garnitures d’étanchéité.
NOTE 1 Pour la présente norme, le terme « raccord » inclut le terme « joint » au sens donné par le mandat M/131.
NOTE 2 Les produits conformes au présent document peuvent être utilisés pour le transport de l’eau destinée à la consommation humaine à condition d’être conformes aux réglementations nationales, régionales ou locales applicables au lieu d’utilisation. La conformité d’un produit au présent document ne confère pas une présomption d'aptitude du produit pour le transport de l'eau destinée à la consommation humaine au sens de la Directive 89/106/CEE.
Cevni sistemi iz polimernih materialov - Cevne komponente za vročo in hladno vodo - Zahteve in preskusi/metode ocenjevanja za cevi in fitinge
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-junij-2011
&HYQLVLVWHPLL]SROLPHUQLKPDWHULDORY&HYQHNRPSRQHQWH]DYURþRLQKODGQR
YRGR=DKWHYHLQSUHVNXVLPHWRGHRFHQMHYDQMD]DFHYLLQILWLQJH
Plastics piping systems - Hot and cold water piping components - Requirements and
test/assessment methods for pipes and fittings
Kunststoff-Rohrleitungssysteme - Bauteile für den Einsatz in Rohrleitungen für Warm-
und Kaltwasser - Anforderungen und Prüf /Bewertungsverfahren für Rohre und
Formstücke
Systèmes de canalisations en plastique - Composants de canalisations pour eau chaude
et froide non destinée à la consommation humaine - Exigences et méthodes
d'essais/d'évaluation pour tubes et raccords
Ta slovenski standard je istoveten z: prEN 15015
ICS:
23.040.20 Cevi iz polimernih materialov Plastics pipes
23.040.45 Fitingi iz polimernih Plastics fittings
materialov
91.140.60 Sistemi za oskrbo z vodo Water supply systems
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
DRAFT
prEN 15015
NORME EUROPÉENNE
EUROPÄISCHE NORM
March 2011
ICS 23.040.01 Will supersede EN 15015:2007
English Version
Plastics piping systems - Hot and cold water piping components
- Requirements and test/assessment methods for pipes and
fittings
Systèmes de canalisations en plastique - Composants de Kunststoff-Rohrleitungssysteme - Bauteile für den Einsatz
canalisations pour eau chaude et froide non destinée à la in Rohrleitungen für Warm- und Kaltwasser -
consommation humaine - Exigences et méthodes Anforderungen und Prüf /Bewertungsverfahren für Rohre
d'essais/d'évaluation pour tubes et raccords und Formstücke
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee CEN/TC 155.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which
stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other language
made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2011 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 15015:2011: E
worldwide for CEN national Members.
prEN 15015:2011 (E)
Contents Page
Foreword .4
Introduction .5
1 Scope .6
2 Normative references .6
3 Terms and definitions .7
4 Requirements .8
4.1 Reaction to fire .8
4.2 Internal pressure strength .8
4.2.1 Determination of design pressure P .8
D
4.2.2 Verification of pressure strength .8
4.3 Dimensional tolerances .8
4.4 Tightness .8
4.5 Durability .9
4.5.1 Durability of internal pressure strength related to the material .9
4.5.2 Durability of the internal pressure strength of pipes and fittings .9
4.5.3 Durability of tightness of connections .9
4.6 Release of dangerous substances .9
5 Test methods .9
5.1 Reaction to fire .9
5.2 Determination of the design pressure .9
5.2.1 Determination of design pressure for thermoplastics pipes and plastic fittings .9
5.2.2 Determination of design pressure for multilayer pipes . 10
5.3 Internal pressure strength . 10
5.4 Dimensional tolerances . 10
5.5 Tightness . 10
5.6 Durability . 10
5.6.1 Durability related to internal pressure strength related to material . 10
6 Evaluation of conformity . 11
6.1 General . 11
6.2 Initial Type Testing – Type Testing . 11
6.2.1 General . 11
Tests previously performed in accordance with the provisions of this standard, respectively
standards as listed in Annex B, may be taken into account provided that they were made
to the same or a more rigorous test method, under the same system of attestation of
conformity on the same product or products of similar design, construction and
functionality, such that the results are applicable to the product in question. . 13
6.2.2 Test samples, testing and compliance . 13
6.2.3 Test reports . 14
6.3 Factory production control (FPC) . 14
6.3.1 General . 14
6.3.2 Requirements . 14
6.3.3 Product specific requirements . 17
6.3.4 Procedure for modifications . 18
6.3.5 One-off products, pre-production products (e.g. prototypes) and products produced in
very low quantity. 18
Annex A (normative) Overall service (design) coefficients . 20
A.1 General . 20
prEN 15015:2011 (E)
A.2 Overall service (design) coefficients . 20
Annex B (normative) Application class S . 21
B.1 General . 21
B.2 Test parameters for temperature cycling . 21
Annex C (informative) Product standards for hot and cold water installations inside buildings . 22
Annex D (informative) Standards for assessment of conformity for hot and cold water
installations inside buildings . 24
Annex ZA (informative) Clauses of this European Standard addressing the provisions of the EU
Construction Products Directive (CPD) . 25
ZA.1. Scope and relevant characteristics . 25
ZA.2. Procedure for attestation of conformity of plastics pipes and fittings . 26
ZA.2.1 System of attestation of conformity . 26
ZA.2.2.CE Certificate and Declaration of conformity . 28
ZA.3. CE marking and labelling. 29
ZA.3.1 CE marking requirements . 29
Bibliography . 33
prEN 15015:2011 (E)
Foreword
This document (prEN 15015:2011) has been prepared by Technical Committee CEN/TC 155 “Plastics piping
systems and ducting systems”, the secretariat of which is held by NEN.
This document is currently submitted to the CEN Enquiry.
This document has been prepared under the mandate M/131 “Pipes, tanks and ancillaries not in contact with
water intended for human consumption” given to CEN by the European Commission and the European Free
Trade Association and support essential requirements of EU Directives.
For relationship with EC Directives, see informative Annex ZA, which is an integral part of this document.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
prEN 15015:2011 (E)
Introduction
This European Standard specifies only those characteristics of pipes and fittings for hot and cold water
applications with the exception of water intended for human consumption that need to be known to determine
if the works in which these are to be installed can satisfy the essential requirements of the EU Directive(s).
Additional characteristics are specified in the documents listed in Annex A or in other appropriate product
specifications.
This harmonised European Standard covers pipes and fittings for hot and cold water installations.
prEN 15015:2011 (E)
1 Scope
This European Standard specifies requirements for plastics pipes and fittings for hot and cold water
installations.
It is intended to be used for distribution of hot and cold water and for heating systems inside buildings with t
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.