EN ISO 8675:2023
(Main)Fasteners - Hexagon thin nuts (style 0), with fine pitch thread (ISO 8675:2023)
Fasteners - Hexagon thin nuts (style 0), with fine pitch thread (ISO 8675:2023)
This document specifies the characteristics of hexagon thin nuts (style 0), in steel and stainless steel, with metric fine pitch thread 8 mm to 64 mm, and with product grades A and B.
Thin nuts used as jam nuts are to be assembled together with a regular or high nut.
WARNING — Thin nuts (style 0) have a reduced loadability compared to regular nuts or high nuts, and are not designed to provide resistance to thread stripping (see ISO 898-2).
If in certain cases other specifications are requested, stainless steel grades and property classes can be selected from ISO 3506-2.
Verbindungselemente - Niedrige Sechskantmuttern (Typ 0), mit metrischem Feingewinde (ISO 8675:2023)
Dieses Dokument legt die Eigenschaften von niedrigen Sechskantmuttern (Typ 0) aus Stahl und nicht-rostendem Stahl mit metrischen Feingewinden 8 mm bis 64 mm und mit Produktklassen A und B fest.
Niedrige Muttern, die als Kontermuttern verwendet werden, müssen gemeinsam mit einer normalen Mutter oder einer hohen Mutter montiert werden.
WARNUNG — Niedrige Muttern (Typ 0) haben im Vergleich zu normalen oder hohen Muttern eine reduzierte Belastbarkeit und sind nicht dafür ausgelegt, dem Abstreifen des Gewindes standzuhalten (siehe ISO 898 2).
Falls in bestimmten Fällen andere Festlegungen benötigt werden, können nichtrostende Stahlsorten und Festigkeitsklassen aus ISO 3506 2 gewählt werden.
Fixations - Écrous bas hexagonaux (style 0), à pas fin (ISO 8675:2023)
Le présent document spécifie les caractéristiques des écrous bas hexagonaux (style 0), en acier et en acier inoxydable, à filetage métrique à pas fin de diamètres 8 mm à 64 mm, et de grades A et B.
Les écrous bas utilisés comme contre-écrou sont à assembler avec un écrou normal ou un écrou haut.
AVERTISSEMENT — Les écrous bas (style 0) ont une capacité de charge réduite par rapport aux écrous normaux ou hauts, et ne sont pas conçus pour fournir une résistance à l’arrachement des filets (voir ISO 898-2).
Si dans certains cas d’autres spécifications sont requises, les grades d’acier inoxydable et les classes de qualité peuvent être choisis dans l'ISO 3506-2.
Vezni elementi - Šestrobe nizke matice (tip 0), z drobnim navojem (ISO 8675:2023)
Ta dokument določa značilnosti šestrobih nizkih matic (tip 0) iz jekla in nerjavnega jekla, z drobnim navojem velikosti od 8 mm do 64 mm ter razredoma izdelave A in B.
Nizke matice, ki se uporabljajo kot tesnilne matice, je treba sestaviti skupaj z običajno ali visoko matico.
OPOZORILO: Nizke matice (tip 0) imajo manjšo obremenljivost v primerjavi z običajnimi maticami ali visokimi maticami in niso zasnovane tako, da zagotavljajo odpornost proti pobiranju navojev (glej ISO 898-2).
Če se v določenih primerih zahtevajo druge specifikacije, je tipe nerjavnega jekla in razrede lastnosti mogoče izbrati v skladu s standardom ISO 3506-2.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 8675:2023
01-november-2023
Vezni elementi - Šestrobe nizke matice (tip 0), z drobnim navojem (ISO 8675:2023)
Fasteners - Hexagon thin nuts (style 0), with fine pitch thread (ISO 8675:2023)
Mechanische Verbindungselemente - Niedrige Sechskantmuttern (Typ 0), mit
metrischem Feingewinde (ISO 8675:2023)
Fixations - Écrous bas hexagonaux (style 0), à pas fin (ISO 8675:2023)
Ta slovenski standard je istoveten z: EN ISO 8675:2023
ICS:
21.040.10 Metrski navoji Metric screw threads
21.060.20 Matice Nuts
SIST EN ISO 8675:2023 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 8675:2023
---------------------- Page: 2 ----------------------
SIST EN ISO 8675:2023
EN ISO 8675
EUROPEAN STANDARD
NORME EUROPÉENNE
September 2023
EUROPÄISCHE NORM
ICS 21.060.20 Supersedes EN ISO 8675:2012
English Version
Fasteners - Hexagon thin nuts (style 0), with fine pitch
thread (ISO 8675:2023)
Fixations - Écrous bas hexagonaux (style 0), à pas fin Mechanische Verbindungselemente - Niedrige
(ISO 8675:2023) Sechskantmuttern (Typ 0), mit metrischem
Feingewinde (ISO 8675:2023)
This European Standard was approved by CEN on 10 June 2023.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2023 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 8675:2023 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 8675:2023
EN ISO 8675:2023 (E)
Contents Page
European foreword . 3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 8675:2023
EN ISO 8675:2023 (E)
European foreword
This document (EN ISO 8675:2023) has been prepared by Technical Committee ISO/TC 2 "Fasteners" in
collaboration with Technical Committee CEN/TC 185 “Fasteners” the secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by March 2024, and conflicting national standards shall
be withdrawn at the latest by March 2024.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 8675:2012.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the
United Kingdom.
Endorsement notice
The text of ISO 8675:2023 has been approved by CEN as EN ISO 8675:2023 without any modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 8675:2023
---------------------- Page: 6 ----------------------
SIST EN ISO 8675:2023
INTERNATIONAL ISO
STANDARD 8675
Fourth edition
2023-08
Fasteners — Hexagon thin nuts
(style 0), with fine pitch thread
Fixations — Écrous bas hexagonaux (
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.