EN ISO 15084:2018

Small craft - Anchoring, mooring and towing - Strong points (ISO 15084:2003)

ISO 15084:2003 specifies requirements for strong points for attaching chains, cables and lines for anchoring, mooring and towing small craft. It does not specify the requirement for the strong point from which the craft can tow other vessels. This standard is applicable to small craft with a hull length up to 24 m.
ISO 15084:2003 does not define anchor weights or the length of chains and lines.

Kleine Wasserfahrzeuge - Ankern, Festmachen und Schleppen - Festpunkte (ISO 15084:2003)

Petits navires - Mouillage, amarrage et remorquage - Points d'ancrage (ISO 15084:2003)

L'ISO 15084:2003 spécifie des exigences relatives aux points d'ancrage des chaînes, câbles et lignes de mouillage, d'amarrage et de remorquage du bateau. Elle ne spécifie pas d'exigence relative au point d'ancrage destiné au remorquage d'autres bateaux. La présente Norme internationale est applicable aux bateaux ayant une longueur de coque inférieure ou égale à 24 m.
L'ISO 15084:2003 ne définit pas la masse des ancres ni la longueur des chaînes ou des lignes.

Mala plovila - Sidranje, privez in vleka - Poudarki (ISO 15084:2003)

Ta mednarodni standard določa zahteve glede fiksirnih točk za pritrjevanje verig, kablov in vrvi za sidranje, privez ter vleko malih plovil. Ne podaja zahtev za fiksirne točke, s pomočjo katere lahko plovilo vleče druga plovila. Ta standard se uporablja za mala plovila z dolžino trupa do 24 m.
Ta mednarodni standard ne določa teže sidra ali dolžine verige in vrvi.

General Information

• Status: Published
• Publication Date: 25-Sep-2018
• ICS: 47.080 - Small craft
• Technical Committee: CEN/TC 464 - Small Craft
• Drafting Committee: CEN/TC 464 - Small Craft
• Current Stage: 6060 - Definitive text made available (DAV) - Publishing
• Start Date: 26-Sep-2018
• Due Date: 03-Nov-2019
• Completion Date: 26-Sep-2018
• Directive: 2003/44/EC - Approximation of the laws, regulations and administrative provisions of the Member States relating to recreational craft
• Directive: 2013/35/EU - Directive 2013/35/EU of the European Parliament and of the Council of 26 June 2013 on the minimum health and safety requirements regarding the exposure of workers to the risks arising from physical agents (electromagnetic fields) (20th individual Directive within the meaning of Article 16(1) of Directive 89/391/EEC) and repealing Directive 2004/40/EC
• Directive: 2013/53/EU - Directive 2013/53/EU of the European Parliament and of the Council of 20 November 2013 on recreational craft and personal watercraft and repealing Directive 94/25/EC
• Mandate: M/542 - [C(2015)8736] Standardisation Request to the European Committee for Standardisation and the European Committee for Electro-technical Standardisation as regards recreational craft and personal watercraft in support of Directive 2013/53/EU of the European Parliament and of the Council of 20 November 2013 on recreational craft and personal watercraft and repealing Directive 94/25/EC.
• Ref Project: SIST EN ISO 15084:2018 - Small craft - Anchoring, mooring and towing - Strong points (ISO 15084:2003)

Relations

• Replaces: EN ISO 15084:2003 - Small craft - Anchoring, mooring and towing - Strong points (ISO 15084:2003)
• Effective Date: 07-Jun-2017

Standards Content (Sample)

SLOVENSKI STANDARD
01-december-2018
1DGRPHãþD
SIST EN ISO 15084:2003
Mala plovila - Sidranje, privez in vleka - Poudarki (ISO 15084:2003)
Small craft - Anchoring, mooring and towing - Strong points (ISO 15084:2003)
Kleine Wasserfahrzeuge - Ankern, Festmachen und Schleppen - Festpunkte (ISO
15084:2003)
Petits navires - Mouillage, amarrage et remorquage - Points d'ancrage (ISO 15084:2003)
Ta slovenski standard je istoveten z: EN ISO 15084:2018
ICS:
47.080 ýROQL Small craft
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 15084
EUROPEAN STANDARD
NORME EUROPÉENNE
September 2018
EUROPÄISCHE NORM
ICS 47.080 Supersedes EN ISO 15084:2003
English Version
Small craft - Anchoring, mooring and towing - Strong
points (ISO 15084:2003)
Petits navires - Mouillage, amarrage et remorquage - Kleine Wasserfahrzeuge - Ankern, Festmachen und
Points d'ancrage (ISO 15084:2003) Schleppen - Festpunkte (ISO 15084:2003)
This European Standard was approved by CEN on 16 April 2018.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 15084:2018 E
worldwide for CEN national Members.

Contents Page
European foreword . 3
Annex ZA (informative) Relationship between this European Standard and the Essential
Requirements of Directive 2013/53/EU aimed to be covered . 4

European foreword
The text of ISO 15084:2003 has been prepared by Technical Committee ISO/TC 188 “Small craft” of the
International Organization for Standardization (ISO) and has been taken over as EN ISO 15084:2018.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by March 2019, and conflicting national standards shall be
withdrawn at the latest by March 2019.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 15084:2003.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive 2013/53/EU.
For relationship with EU Directive 2013/53/EU, see informative Annex ZA, which is an integral part of
this document.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia,
Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands,
Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
the United Kingdom.
Endorsement notice
The text of ISO 15084:2003 has been approved by CEN as EN ISO 15084:2018 without any modification.
Annex ZA
(informative)
Relationship between this European Standard and the Essential
Requirements of Directive 2013/53/EU aimed to be covered
This European standard has been prepared under a Commission’s standardization request M/542
C(2015) 8736 final to provide one voluntary means of conforming to Essential Requirements of Directive
2013/53/EU.
Once this standard is cited in the Official Journal of the European Union under that Directive, compliance
with the normative clauses of this standard given in Table ZA.1 confers, within the limits of the scope of
this standard, a presumption of conformity with the corresponding Essential Requirements of that
Directive and associated EFTA regulations.
Table ZA.1 — Correspondence between this European Standard and Annex I of Directive
2013/53/EU
Essential Requirements of Directive Clause(s)/sub-clause(s) of Remarks/Notes
2013/53/EU this EN
Annex I, Part A, 3.9 - Anchoring, mooring and towing 4, 5, 6, 7
Annex I, Part A, 2.5 – Owner’s manual 8, Annex A
WARNING 1 — Presumption of conformity stays valid only as long as a reference to this European
Standard is maintained in the list published in the Official Journal of the European Union. Users of this
standard should consult frequently the latest list published in the Official Journal of the European Union.
WARNING 2 — Other Union legislation may be applicable to the product(s) falling within the scope of
this standard.
INTERNATIONAL ISO
STANDARD 15084
First edition
2003-02-15
Small craft — Anchoring, mooring and
towing — Strong points
Petits navires — Mouillage, amarrage et remorquage — Points
d'ancrage
Reference number
ISO 15084:2003(E)
©
ISO 2003
ISO 15084:2003(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.

©  ISO 2003
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.org
Published in Switzerland
ii © ISO 2003 — All rights reserved

ISO 15084:2003(E)
Contents Page
Foreword. iv
1 Scope. 1
2 Normative references . 1
3 Terms and definitions. 1
4 Symbols . 2
5 General requirements . 2
6 Strength requirements. 3
7 Detailed requirements . 4
8 Owner’s manual . 4
9 Strength of synthetic fibre ropes . 4
Annex A (normative) Information to be provided in the owner’s manual . 5
Annex B (informative) Material strength of synthetic fibre ropes/dimensions of strong points. 6
Bibliography . 7

ISO 15084:2003(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carr
...